9500 MPR Product Information PN 3EM23952AA 01 R02.
THIS PRODUCT COMPLIES WITH D.H.H.S. RADIATION PERFORMANCE STANDARDS 21 CFR, 1040.10, FOR A CLASS 1 LASER PRODUCT. DANGER Invisible laser radiation is present when the optic connector is open. AVOID DIRECT EXPOSURE TO BEAM. WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
ALCATEL-LUCENT PRACTICE Standard 3EM23952AA Issue 01, September 2009 9500 MPR Product Information Table of Contents FCC Part 15 Subpart B 1. 9500 MPR UNLICENSED RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 FCC Class B Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 FCC Class B Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 9500 MPR General System Description 1. INTRODUCTION . . . . .
3EM23952AA Issue 01, September 2009 UDS-117 ii GigE SFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3EM23952AA Issue 01, September 2009 9500 MPR Product Information List of Figures Figure 2-1. Frequency Plan: 5.725 to 5.850 GHz Unlicensed Band (FCC Part 15) . . . . . . . . . . . . 2-13 Figure 2-2. Stand-Alone Microwave Service Switch (MSS-8) shelf . . . . . . . . . . . . . . . . . . . . . . . . 2-16 Figure 2-3. All Indoor Mount - 1+0 Terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 Figure 2-4. All Indoor Mount - 1+0 Drop and Insert Repeater . . . . .
3EM23952AA Issue 01, September 2009 Figure 101-9. MSS-8 Shelf Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Figure 113-1. P32E1DS1 DS1 Module (MSS/DS1) Front Panel View . . . . . . . . . . . . . . . . . . . . . . . . 3-28 Figure 114-1. P2E3DS3 DS3 Module (MSS/DS3) Front Panel View . . . . . . . . . . . . . . . . . . . . . . . . . 3-30 Figure 115-1. P8ETH Module (MSS/P8ETH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3EM23952AA Issue 01, September 2009 9500 MPR Product Information List of Tables Table 2-A. 5.8 GHz Unlicensed Antenna Recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Table 2-G. Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24 Table 3-A. 9500 MPR Unit Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27 Table 101-A.
3EM23952AA Issue 01, September 2009 vi List of Tables
3EM23952AA Issue 01, September 2009 FCC Part 15 Subpart B 1. 9500 MPR UNLICENSED RADIO 1.1 The JF6-9558H (unlicensed) radio provides fast deployment of service with microwave radio. No license and small antennas (no FCC requirements) allow immediate turn-up. After the license is received, the unlicensed radio can be easily converted to the lower 6 GHz licensed band. 1.2 The JF6-9558H unlicensed radio operates in the 5725-5850 Information, Scientific, and Medical (ISM) band in accordance with FCC Part 15.
3EM23952AA Issue 01, September 2009 CAUTION 1-2 Possibility of service interruption. Installation, Turn-Up, Maintenance, and Operation Instruction supplied with the JF6-9558H (unlicensed) radio require strict adherence for continued part 15 of the FCC Rules and IC RSS-210 compliance.
3EM23952AA Issue 01, September 2009 9500 MPR General System Description 1. INTRODUCTION 1.1 This General System Description applies to 9500 MPR software release R02.00 (hereafter called R02.00) and any subsequent or maintenance release to this release. It describes system applications, floor space, and power requirements. Signal input and output characteristics are also defined.
3EM23952AA Issue 01, September 2009 1.8 System control and synchronization is provided by the Enhanced Control and Switching Module (CSM-E) module. Documentation 1.
3EM23952AA Issue 01, September 2009 Standards 1.10 The following is a partial list of the standards that have influenced certain behavioral aspects of the 9500 MPR: • 21 CFR PART 1040.10 and 1040.11 • Banned substances list • CENELEC EN 61000-3-2 • CENELEC EN 61000-3-3 • CENELEC EN 61000-4-8 • CISPR/I/105/CDV-CISPR/I/29/CD-CISPR/I/106/CDV • CISPR 16-1-1 • CISPR 16-1-2 • CISPR 16-1-4 • CISPR 16-2-1 • CISPR 16-2-3 • CISPR 16-2-4 • CISPR 16-4-2 • CSA-C22.
3EM23952AA Issue 01, September 2009 2-4 • ETSI and RTTE directive: ETSI standard • ETSI and RTTE directive: EN 302 217 • ETSI standards: Transmitter requirements • ETSI standards: Receiving requirements • ETSI standards: Note • ETSI EN 302 217-1 to 4 • ETSI EN 301 489 • ETSI EN 300 019 • ETS 300 753 • ETSI EN 300 132-2 • ETSI EN 300 132-3 • EU Directive EuP Directive 92/42/EEC, Compliance with proposal • FCC OET 65 • FCC Title 247, Part 15 • GR-487-CORE • GR-1089-CORE • Hu
3EM23952AA Issue 01, September 2009 • IEEE Std 802.3 • IEEE Std 802.1D • IEEE Std 802.1Q • IETF RFC 2474 • IETF RFC 2475 • IETF RFC 3550 • IETF RFC 0793 • IETF RFC 0791 • IETF RFC 1157 • IETF RFC 768 • IETF RFC 2616 • ITU-T G.664 • ITU-T G.703 • ITU-T G.704 • ITU-T G.706 • ITU-T G.775 • ITU-T G.823 • ITU-T G.8261 • ITU-T G.826 • ITU-T G.
3EM23952AA Issue 01, September 2009 • TR NWT 000499 • TR TSY 000191 FCC Part 15 Subpart B 1.11 The JF6-9558H (unlicensed) radio provides fast deployment of service with microwave radio. No license and small antennas (no FCC requirements) allow immediate turn-up. After the license is received, the unlicensed radio can be easily converted to the lower 6 GHz licensed band. 1.
3EM23952AA Issue 01, September 2009 2. FEATURES 2.1 This section describes 9500 MPR features of the 9500 MPR R02.00. 2.2 The following paragraphs describe the features of the system for R02.00. To administer these new features by the Craft Terminal and WebEML refer to the 9500 MPR Operation and Administration manual (PN 3EM23954AA).
3EM23952AA Issue 01, September 2009 System Features • All Indoor Mount mechanical arrangement – 2-8 Up to 8 radio directions per node • Frequencies: 5.
3EM23952AA Issue 01, September 2009 • TSM8000 Support • 1340 INC Support • 1350 OMS Support System Architecture • All Indoor Mount mechanical arrangement – Up to 8 radio directions per node • Frequencies: 5.8 Unlicensed, 6L, and 6U GHz • Static Modulation • Bandwidths: 2.5, 3.
3EM23952AA Issue 01, September 2009 System Architecture All Indoor Mount mechanical arrangement 2.3 The system allows up to eight radio channels per node. 2.4 The radio channels can be either, all the same frequency, different frequencies, or a combination of both. 2.5 LICENSED RADIO: The 6L and 6U GHz frequencies are supported in the all indoor mount arrangement.
3EM23952AA Issue 01, September 2009 UNLICENSED RADIO 2.6 The JF6-9558H unlicensed radio provides fast deployment of service with microwave radio. No license and small antennas (no FCC requirements) allow immediate Turn-Up. After the license is received, the unlicensed radio can be easily converted to the lower 6 GHz licensed band. 2.
3EM23952AA Issue 01, September 2009 Antenna Recommendations: 2.11 • Frequency – 5.8 GHz • Size and Type – 2, 4, 6, 8, or 10 foot parabolic; 1 or 2 foot flat panel. • – Parabolic antennas, See Table 2-A. – Flat antennas, See Table 2-A. Gain and Bemired (3 dB) Table 2-A. 5.8 GHz Unlicensed Antenna Recommendation PARABOLIC FLAT 2 ft parabolic – 29 dB/6° 1 ft flat panel – 23 dB/9° 4 ft parabolic – 35 dB/3° 2 ft flat panel – 28 dB/3.5° 6 ft parabolic – 38 dB/2° 8 ft parabolic – 41 dB/1.
3EM23952AA Issue 01, September 2009 Figure 2-1. Frequency Plan: 5.725 to 5.850 GHz Unlicensed Band (FCC Part 15) 5725 5787.
3EM23952AA Issue 01, September 2009 2.14 Static Modulation is supported in the all indoor mount arrangement. 2.15 Bandwidths: 5, 10, and 30 MHz are supported in the all indoor mount arrangement 2.16 Modulations: 32 QAM, 128 QAM, and 256 QAM 2.17 Ethernet Access Switch transponder module 2.18 Four 10/100/1000BaseT Ethernet ports 2.19 Four GigE SFP optical Ethernet ports System Architecture Architecture 2.
3EM23952AA Issue 01, September 2009 Microwave Service Switch (MSS-8) Shelf 2.26 1+0 and 1+1 EPS on All DS1, DS3, and 10/100/1000 Ethernet interfaces 2.27 CESoETH 2.28 MEF8 2.29 Microwave uplink 2.30 Ethernet uplink with VLAN 2.31 Point-to-point VLAN 2.32 IEEE 802.1p and Diffserv QoS 2.33 Queue Management & Flow control ability 2.34 Channel Spacing: 2.35 SW License control 2.36 SNMP v2 2.37 TSM8000 Support 2.38 1340 INC Support 2.39 1350 OMS Support System Configurations 2.
3EM23952AA Issue 01, September 2009 Figure 2-2. Stand-Alone Microwave Service Switch (MSS-8) shelf 2.41 All Indoor Mount - 1+0 Terminal: See Figure 2-3. Figure 2-3. All Indoor Mount - 1+0 Terminal 2.42 2-16 All Indoor Mount - 1+0 Drop and Insert Repeater: See Figure 2-4.
3EM23952AA Issue 01, September 2009 Figure 2-4. All Indoor Mount - 1+0 Drop and Insert Repeater 2.43 All Indoor Mount - 1+0 4-Way Junction: See Figure 2-5.
3EM23952AA Issue 01, September 2009 Figure 2-5. All Indoor Mount - 1+0 4-Way Junction 2.44 All Indoor Mount - 1+0 8-Way Nodal Junction: See Figure 2-6. Figure 2-6. All Indoor Mount - 1+0 8-Way Nodal Junction 2.45 All Indoor Mount - 1+1 Terminal: See Figure 2-7. Figure 2-7.
3EM23952AA Issue 01, September 2009 2.46 All Indoor Mount - 1+1 HSB Drop and Insert Repeater: See Figure 2-8. Figure 2-8. All Indoor Mount - 1+1 HSB Drop and Insert Repeater 2.47 All Indoor Mount - 1+1 HSB 4-Way Junction: See Figure 2-9.
3EM23952AA Issue 01, September 2009 Figure 2-9.
3EM23952AA Issue 01, September 2009 MSS (Microwave Service Switch) Figure 2-2. Macerate Service switch (MSS-8) MSS-8 Configurations A MSS-8 typical configuration consists of: 2.48 • MSS-8 Typical Configuration • MSS-8 Not Protected • MSS-8 Protected Figure 2-3.
3EM23952AA Issue 01, September 2009 Figure 2-4. MSS-8 Typical Configuration NOTE: Adjacent slot must be same P32E1DS1, MD300 or P2E3DS3 module for protection. Not all slots may require protection. Any P32E1DS1, MD300 or P2E3DS3 module can be installed in any not protected slot(s). The Main CSM (Control and Switching Module - Core) must always be in slot 1 and the Protect CSM must be in slot 2. Figure 2-5.
3EM23952AA Issue 01, September 2009 NOTE: Adjacent slot must be same P32E1DS1, MD300 or P2E3DS3 module for protection. Not all slots may require protection. Any P32E1DS1, MD300 or P2E3DS3 module can be installed in any not protected slot(s). The Main CSM (Control and Switching Module - Core) must always be in slot 1. Figure 2-6. MSS-8 Protected Configuration NOTE: Adjacent slot must be same P32E1DS1, MD300 or P2E3DS3 module for protection. Not all slots may require protection.
3EM23952AA Issue 01, September 2009 Table 2-G. Configurations ITEM DESCRIPTION Microwave Switching Services (MSS-8) Shelf PN: 3DB18001AA Qty: 1 per node The MSS-8 houses equipment that supports 10 Gb/s packet switching, synchronization, protection switching, provisioning, and alarm management utilizing either one CSM module in unprotected configuration or two CSM modules in protected configuration. Six transponder slots support any mixture of unprotected and/or 1+1 EPS protected transponder modules.
3EM23952AA Issue 01, September 2009 Facility Alarms 2.52 Facility alarms indicate failures of a DS1 and/or Ethernet. Facility alarms and parameters can be established individually. Notification codes follow: • Critical (CR) • Major (MJ) • Minor (MN) • Cleared (CL) Remote Inventory 2.53 Remote Inventory (RI) provides operators with the capability to remotely determine what equipment is installed in the system.
3EM23952AA Issue 01, September 2009 2-26 9500 MPR General System Description
3EM23952AA Issue 01, September 2009 3. UNIT DESCRIPTIONS 3.1 Refer to table 3-A for brief descriptions of shelf assemblies, plug-in modules, and miscellaneous components used in the 9500 MPR. Table 3-A. 9500 MPR Unit Descriptions UNIT DESCRIPTION Microwave Switching Services (MSS-8) Shelf PN: 3DB18001AA Qty: 1 per 9500 MPR node The MSS-8 houses equipment that supports 10 Gb/s packet switching, synchronization, protection switching, provisioning, and alarm management.
3EM23952AA Issue 01, September 2009 Table 3-A. 9500 MPR Unit Descriptions (cont.) UNIT DESCRIPTION DS1 D-Connector Patch Panel PN: 3DB16102AA Qty: Up to 6per 9500 MPR node DS1 D-Connector Patch Panel supports up to 32 protected or unprotected DS1 (Tx and Rx) interfaces. DS1 DConnector Patch Panel provides 32 customer interconnects using 37-position D-Sub connectors for terminating traditional ABAM cable.
UDS-100 3EM23952AA Issue 01, September 2009 UDS-100 9500 MPR Unit Data Sheet Cross-Reference Unit Data Sheets (UDSs) Unit Data Sheet Cross-Reference by UDS Number UDS NUMBER DESCRIPTION CLEI STATUS PART NUMBER UDS-100 9500 MPR Unit Data Sheet Cross-Reference NA NA NA UDS-101 MSS-8 Microwave Service Switch Shelf 1 Active 3DB18001AA UDS-102 MPT-HL Microwave Packet transport-Long 1 Haul Shelf Active 3EM22618AA UDS-104 PDU Power Distribution Unit 1 Active 3EM13317AA UDS-106 DS1 RJ-45
UDS-100 3EM23952AA Issue 01, September 2009 Unit Data Sheet Cross-Reference by Part Number PART NUMBER DESCRIPTION CLEI UDS STATUS NUMBER 1AF15245AB DS1 RJ-45 Patch Panel 1 Active UDS-106 3DB16102AA DS1 D-Connector Patch Panel 1 Active UDS-107 3DB18001AA MSS-8 Microwave Service Switch Shelf 1 Active UDS-101 3DB18126AD P32E1DS1 DS1 PDH Module 1 Active UDS-113 3DB18134BA Fan Card 1 Active UDS-110 3DB18206AC P8ETH Ethernet Access Switch Module 1 Active UDS-115 3DB18326AB CS
UDS-101 3EM23952AA Issue 01, September 2009 UDS-101 MSS-8 Microwave Service Switch Shelf PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3DB18001AA 1 2 3 Active MSS-8 Microwave Service Switch Shelf FEATURES AND APPLICATION NOTES • The Microwave Service Switch (MSS-8) shelf provides crossconnection, port aggregation, switching, and equipment management.
UDS-101 3EM23952AA Issue 01, September 2009 The MSS-8 shelf is 19 inches wide (17.48 inches wide without mounting flanges), 3.46 inches high (2 EIA increments), and 9.54 inches deep. Adapter plates are available to mount the MSS-8 shelf in 23 inch aluminum racks. Figure 101-1. Microwave Service Switch (MSS-8) Shelf EQUIPMENT COMPLEMENT MSS-8 shelf slots 1 and 2 are dedicated to the CSM module. Slots 3 through 8 are available for transport modules P32E1DS1, P2E3DS3. Slots 3 and 4 are available for P8ETH.
UDS-101 3EM23952AA Issue 01, September 2009 Figure 101-2. MSS-8 Shelf Slot Definitions 1 3 2 CSM (Main) Any Transponder P32E1DS1 or P8ETH 5 4 9 CSM (Protect) Any Transponder P32E1DS1 or P8ETH Fan 6 P32E1DS1 7 P32E1DS1 8 P32E1DS1 P32E1DS1 950-0004-1 072209 Table 101-A. MSS-8 Module Complement CIRCUIT PACK/ UNIT DATA SHEET PART NO.
UDS-101 3EM23952AA Issue 01, September 2009 MSS-8 shelf slot 1 is dedicated to the main CSM module and is required in every application. See figure 101-3 to see an example of the MSS-8 shelf configured in the unprotected CSM configuration. Slot 2 is dedicated for an optional spare CSM module for protected CSM configurations. See figure 101-4 to see an example of the MSS-8 shelf configured in the protected CSM configuration. Figure 101-3.
UDS-101 3EM23952AA Issue 01, September 2009 Figure 101-4. MSS-8 Shelf, Protected CSM Configuration 1 CSM (Main) 3 2 CSM (Protect) 9 4 Any Transponder 5 Any Transponder Fan 6 Any Transponder 7 Any Transponder 8 Any Transponder Any Transponder 950-0005-1 072209 MSS-8 shelves supports up to six P32E1DS1 module in unprotected DS1 aggregation configurations. Supports up to three pairs of P32E1DS1 modules in 1+1 EPS protected DS1 aggregation configurations.
UDS-101 3EM23952AA Issue 01, September 2009 Figure 101-5. MSS-8 Stand-Alone Shelf, Equipped with P32E1DS1 1 3 5 7 CSM (Main) P32E1DS1 (Main) P32E1DS1 (Main) P32E1DS1 (Unprotected) 2 4 6 8 CSM (Protect) 9 P32E1DS1 (Protect) Fan P32E1DS1 (Protect) P32E1DS1 (Unprotected) 950-0007-1 072209 MSS-8 shelves supports up to six P2E3DS3 modules in unprotected configurations. Supports up to three pairs of P2E3DS3 modules in 1+1 EPS protected configurations.
UDS-101 3EM23952AA Issue 01, September 2009 Figure 101-6. MSS-8 Stand-Alone Shelf, Equipped with P32E1DS1 1 3 5 7 CSM (Main) P2E3DS3 (Main) P2E3DS3 (Main) P2E3DS3 (Unprotected) 2 4 6 8 CSM (Protect) 9 P2E3DS3 (Protect) Fan P2E3DS3 (Protect) P2E3DS3 (Unprotected) 950-0008-1 072209 MSS-8 shelves equipped with P8ETH modules, the main P8ETH is required in slot 3 for unprotected configurations.
UDS-101 3EM23952AA Issue 01, September 2009 Figure 101-7. MSS-8 Shelf, All Indoor Mount, 1+0 4-Way Junction Configuration 1 3 5 CSM (Main) P8ETH (Main) P32E1DS1 (Main) 7 2 CSM (Protect) 9 4 Filler Panel 6 Fan P32E1DS1 (Protect) 8 Filler Panel Filler Panel 950-0011-1 072209 See figure 101-8 to see an example of the MSS-8 shelf configured as an all indoor mount, 1+1 4-way junction in slots 3 and 4, with three P32E1DS1s in slot 5 through 7 in the unprotected configuration.
UDS-101 3EM23952AA Issue 01, September 2009 Figure 101-8.
UDS-101 3EM23952AA Issue 01, September 2009 FUNCTIONAL OVERVIEW MSS-8 implements functionality of grooming, routing, switching and protection, exploiting a packet oriented technology in order to meet the overall architecture. The MSS-8 CSM platform, with multiplexing and symmetrical cross-connect functions, can manage different radio directions (up to eight), with the possibility to add-drop data flows of local DS1/Ethernet traffic.
UDS-101 3EM23952AA Issue 01, September 2009 The MSS-8 shelf houses the following modules: • CSM Control and Switching Module—houses one main and one optional protect control and switching module(s). Provides four 10/100/1000 Base-T Ethernet ports.
UDS-101 3-14 3EM23952AA Issue 01, September 2009 MSS-8 Microwave Service Switch Shelf
UDS-102 3EM23952AA Issue 01, September 2009 UDS-102 MPT-HL Microwave Packet Transport-Long Haul Shelf PART NUMBER/ NAME MNEMONIC 3EM22618AA CLEI MPT-HL Microwave Packet 1 transport-Long Haul Shelf ECI/ BAR CODE CPR STATUS 2 3 Active FEATURES AND APPLICATION NOTES DESCRIPTION EQUIPMENT COMPLEMENT MPT-HL Microwave Packet Transport-Long Haul Shelf 3-15
UDS-102 3-16 3EM23952AA Issue 01, September 2009 MPT-HL Microwave Packet Transport-Long Haul Shelf
UDS-104 3EM23952AA Issue 01, September 2009 UDS-104 PDU Power Distribution Unit PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3EM13317AA 1 2 3 Active PDU Power Distribution Unit FEATURES AND APPLICATION NOTES DESCRIPTION EQUIPMENT COMPLEMENT PDU Power Distribution Unit 3-17
UDS-104 3EM23952AA Issue 01, September 2009 FUNCTIONAL OVERVIEW 3-18 PDU Power Distribution Unit
UDS-106 3EM23952AA Issue 01, September 2009 UDS-106 DS1 RJ-45 Patch Panel PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 1AF15245AB 1 2 3 Active DS1 RJ-45 Patch Panel FEATURES AND APPLICATION NOTES DESCRIPTION CONNECTORS FUNCTIONAL OVERVIEW DS1 RJ-45 Patch Panel 3-19
UDS-106 3-20 3EM23952AA Issue 01, September 2009 DS1 RJ-45 Patch Panel
UDS-107 3EM23952AA Issue 01, September 2009 UDS-107 DS1 D-Connector Patch Panel PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3DB16102AA 1 2 3 Active DS1 D-Connector Patch Panel FEATURES AND APPLICATION NOTES DESCRIPTION CONNECTORS FUNCTIONAL OVERVIEW DS1 D-Connector Patch Panel 3-21
UDS-107 3-22 3EM23952AA Issue 01, September 2009 DS1 D-Connector Patch Panel
UDS-109 3EM23952AA Issue 01, September 2009 UDS-109 CSM-E Enhanced Control and Switching Module PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3DB18326AB 4 5 6 Active CSM-E Enhanced Control and Switching Module FEATURES AND APPLICATION NOTES DESCRIPTION INDICATORS, CONNECTORS, AND CONTROL FUNCTIONAL OVERVIEW CSM-E Enhanced Control and Switching Module 3-23
UDS-109 3-24 3EM23952AA Issue 01, September 2009 CSM-E Enhanced Control and Switching Module
UDS-110 3EM23952AA Issue 01, September 2009 UDS-110 Fan Card PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3DB18134BA 1 2 3 Active Fan Card FEATURES AND APPLICATION NOTES DESCRIPTION CONNECTORS FUNCTIONAL OVERVIEW Fan Card 3-25
UDS-110 3-26 3EM23952AA Issue 01, September 2009 Fan Card
UDS-113 3EM23952AA Issue 01, September 2009 UDS-113 P32E1DS1 DS1 PDH Module PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3DB18126AD 1 2 3 Active P32E1DS1 DS1 PDH Module FEATURES AND APPLICATION NOTES • Terminates up to 32 DS1 signals • Framed DS1 Bi-Directional alarm management • Bi-Directional performance monitoring on framed DS1 signals • Encapsulation of DS1 data flows into standard Ethernet packets Inter Working Function (IWF) • Extraction of DS1 data flows from standar
UDS-113 3EM23952AA Issue 01, September 2009 ITEM FUNCTION STATUS (S) • • • • • • Off - Card not equipped, not provisioned, or not powered Green Blinking - Download, Software Booting, or Flash Module Realignment in Progress Green - In Service, Normal Operation, and Properly Provisioned Yellow - In Protect, Properly Provisioned as EPS Red - Card Fail Red Blinking - Card Mismatch I/O (16-1) 64 position SCSI connector: • DS1, Tx and Rx (tip and ring), interconnect • DS1s number 1 through 16 I/O (32-17)
UDS-114 3EM23952AA Issue 01, September 2009 UDS-114 P2E3DS3 DS3 PDH Module FEATURES AND APPLICATION NOTES • Terminates up to two DS3 signals.
UDS-114 3EM23952AA Issue 01, September 2009 Figure 114-1. P2E3DS3 DS3 Module (MSS/DS3) Front Panel View FUNCTIONAL OVERVIEW In the transmit direction, the P2E3DS3 receives DS3 signals from the customer interfaces. Encapsulates the DS3 data flows into standard Ethernet packets, (IWF). The Ethernet packets are sent to the cross-connections matrix for connection to their provisioned destinations.
UDS-115 3EM23952AA Issue 01, September 2009 UDS-115 P8ETH Ethernet Access Switch Module PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3DB18206AC 1 2 3 Active P8ETH Ethernet Access Switch Module FEATURES AND APPLICATION NOTES • Terminates up to four GigE optical Ethernet SFP interfaces • Terminates up to four 10/100/1000 electrical Ethernet interfaces • Framed DS3 Bi-Directional alarm management • Bi-Directional performance monitoring on framed DS3 signals • Encapsulation of
UDS-115 3EM23952AA Issue 01, September 2009 INDICATORS, CONNECTORS, AND CONTROL The P2E3DS3 DS3 PDH module has the following indicator and connectors. See figure 115-1 for P2E3DS3 DS3 PDH module front panel indicator and connectors.
UDS-116 3EM23952AA Issue 01, September 2009 UDS-116 MPT Transceiver PART NUMBER/ NAME MNEMONIC CLEI ECI/ BAR CODE CPR STATUS 3EM22617AA MPT Transceiver L6, 5725-6425 MHz 1 2 3 Active 3EM22617AB MPT Transceiver U6, 6425-6930 MHz 4 5 6 Active FEATURES AND APPLICATION NOTES DESCRIPTION INDICATORS, CONNECTORS, AND CONTROL FUNCTIONAL OVERVIEW MPT Transceiver 3-33
UDS-116 3-34 3EM23952AA Issue 01, September 2009 MPT Transceiver
UDS-117 3EM23952AA Issue 01, September 2009 UDS-117 GigE SFP PART NUMBER/ NAME MNEMONIC CLEI 3EM20277AA GigE SFP 1000Base-SX, 850 nm 3EM20277AB ECI/ BAR CODE CPR STATUS DRR3AA3CAA 147527 U73234 Active GigE SFP 1000Base-LX, 1310 nm DRR3AA4CAA 147539 U73235 Active 3EM20277AC GigE SFP 1000Base-EX, 1310 nm DRR3AA5CAA 147542 U73236 Active 3EM20277AD GigE SFP 1000Base-ZX, 1550 nm DRR3AA6CAA 147544 U73237 Active FEATURES AND APPLICATION NOTES • Is an in-service pluggable optical module
UDS-117 3EM23952AA Issue 01, September 2009 INDICATORS, CONNECTORS, AND CONTROL The SFPs have the following indicators and connector. ITEM FUNCTION LINK Off indicates GigE link is down. Green LED indicates GigE link is Up. ACTIVITY Off indicates no activity on GigE link. Blinking amber LED indicates activity on GigE link. DUPLEX LC OPTICAL CONNECTOR Tx and Rx GigE ports FUNCTIONAL OVERVIEW The GigE SFP interfaces with the CSM or EAS through a 2.5 Gb/s data signal line.
UDS-117 3EM23952AA Issue 01, September 2009 Figure 117-1. Optical SFP Module Transceiver CSM SFP module Transceiver EAS SFP module Output Input Optical cables 950-0001-1 072009 On the transmitter side, the GigE SFPs has an automatic optical output power control circuit, a laser driver and a laser diode module. The transmitter is based on a non-cooled DFB laser. The laser safety class for the complete integrated module is class 1 according to IEC 60825.
UDS-117 3EM23952AA Issue 01, September 2009 Figure 117-2. Optical SFP Module Block Diagram SFP MODULE MONITOR PIN PD HOST MODULE TD+ LD LASER DRIVER 100 7 TD- VccT VccT 4.7 k7 TO 10 k7 4.7 k7 TX DISABLE AUTOMATIC POWER CONTROL CIRCUIT TX FAULT (A) TRANSMITTER PIN PD RD+ PREAMP POSTAMP 100 7 RD- VccR 4.7 k7 TO 10 k7 LOS (B) RECEIVER TEMPERATURE SUPPLY VOLTAGE TX BIAS CURRENT TX OUTPUT POWER RX RECEIVED POWER VccT DIAGNOSTIC MONITOR MOD-DEF (0) EEPROM 4.