User's Guide

Alcatel-Lucent Enterprise
OmniAccess Stellar AP1311 series
Installation Guide
060672-10 Rev. A
060672-10
https://www.al-enterprise.com
The Alcatel-Lucent name and logo are trademarks of Nokia used under license by ALE. To view
other trademarks used by affiliated companies of ALE holding, visit: https://www.al-
enterprise.com/en/legal/trademarks-copyright. All other trademarks are the property of their
respective owners. The information presented is subject to ALE without notice. Neither ALE
Holding nor any of its affiliates assumes any responsibility for inaccuracies contained herein.
(2020)
Summary of Installation Steps
• WLAN Planning. Usually, a comprehensive site survey is required
before installation, such as installation location, brackets, cables,
power source, etc.
• Unpack the AP box and check all contents
• Install the AP bracket on ceiling or wall
• Installing the AP
• Connecting required cables
• Power connection
• Verifying post-installation connectivity
• AP provisioning
Access points are radio transmission devices and are subject to
governmental regulation. Network administrators who are
responsible for the configuration and operation of access points must
comply with local broadcast regulations. Specifically, access point
must use channel assignments appropriate to the location where the
access point will be deployed.
Package Contents
Item
Name
Qty
Unit
1
Access Point
1
Pcs
2
Quick Start Guide
1
Pcs
Installation Guide
1
Pcs
Regulatory Compliance and Safety
Information
1
Pcs
User Guide Info Card
1
Pcs
◆ Optional Accessories（To be ordered separately）
Item
Name
Description
1
OAW-AP-MNT-B
Indoor mounting kit, Type B1(9/16") and
B2(15/16") for T shaped ceiling rail.
2
OAW-AP-MNT-C
Indoor mounting kit, Type C1(Open
Silhouette) and C2 (Flanged Interlude),
for other shaped ceiling rail mounting.
3
OAW-AP-MNT-W
Indoor mounting kit, Type W wall and
ceiling mounting with screws.
Figure1: Product Packing
Inform your ALE sales representative of incorrect, missing, or
damaged parts. If possible, retain the carton, including the
original packing materials. Use these materials to repack and
return the unit to the supplier if needed. Additional mounting
kits for use with the OmniAccess Stellar access points are sold
separately. Contact your ALE sales representative for details.
Hardware Overview
The following sections outline the hardware components of the OAW-
AP1311 Series access point.
Figure 2: OAW-AP1311 Front View
LED
The OAW-AP1311 Series access point is equipped with hidden LED display
that indicates different status with different color.
For the details of the LED status, please refer to the Quick Start Guide.
Figure 3: OAW-AP1311 Back View
◆ OAW-AP1311 series External Interfaces
Table 1
Interface
Specifications
1 Gigabit
Eth0
1x 10/100/1000BASE-T autosensing (RJ-45) port, Power
over Ethernet (PoE). In case of only one WAN link，Eth0
would be preferred.
1 Gigabit
Eht1
1x 10/100/1000BASE-T autosensing (RJ-45) port, Power
over Ethernet (PoE). In case of only one WAN link，
either of Eth0 and Eth1 could work as WAN, Eth0 would
be more preferred. In case of two WAN links，Eth0 +
Eth1 would be preferred.
1 Gigabit
LAN
1x 10/100/1000BASE-T autosensing (RJ-45) port.
Console
RJ-45 female connector, default is RS-232 Console for
Service & Support only. Support software configure to
RS-485 mode.
USB
USB 2.0 host interface (Type C, output current 0.5A )
DC Power
Socket
DC 48V power jack, support powering AP through a
designated AC-DC power adapter.
Reset
Factory reset. Press reset button for 5s, AP LEDs will
quickly flash for 3s, then AP will restart and restore
factory configurations.
Security
Lock Slot
The AP is equipped with a security lock slot for
additional security.