ALCATEL 2315 USER GUIDE 2315 Hotel set The manufacturer reserves the right to modify any product characteristics without prior notice. RCS Nanterre 390 546 059 Downloaded from - http://www.guardianalarms.
1. LAYOUT 2. INSTALLATION 3. OUTGOING CALL 3.1 Handset Mode 3.2 Handsfree Mode 4. INCOMING CALL 4.1. Handset Mode 4.2. Handsfree Mode 5. HOLD 5.1. Handset Mode 5.2. Handsfree Mode 6. HOLD TRANSFER 6.1. Handset Mode 6.2. Handsfree Mode 7. SPECIAL SIGNALLING KEYS 7.1. Rd Last Number Redial 7.2. Pause 7.3. R Flash 7.4. +,- Volume Control 8. DATA PORT 9. MANUAL PROGRAMMING 9.1. Select Manual Programming Mode 9.2. Setting Service Buttons Or Message Key Code 9.3.
1. LAYOUT Message indicator signal select switch (under index label) Service buttons Data port Jack RING VOL Ringer volume 1 2 3 Mail button & indicator 4 5 6 7 8 9 * 0 # - + Receive volume control 2. Speakerphone indicator ❶ (handsfree) Speakerphone led ❷ (handsfree) INSTALLATION 2315 Hotel set The manufacturer reserves the right to modify any product characteristics without prior notice.
Before connection to the PBX, the service buttons, ringer melody and flash timing should be pre-programmed according to the customization parameters, either with the customization tool or by manual entry. The selection switch for the message indicator switch should be set manually to appropriate position in order to work with the installed PBX. Failure may result in the loss of the message indicator function or even result in malfunction of the phone with PBX.
3.2. • ♦ ♦ ♦ ♦ Handsfree mode: Press the Speakerphone indicator ❶ button. The Speakerphone led ❷ lights up. Listen for dial tone Dial the number by pressing the dial keypad or any of the service buttons or the Mail button. Press the + or – button to adjust receive volume To converse in handset mode, just pick up the handset. The Speakerphone led ❷ will be off. Press the Speakerphone indicator ❶ button when conversation is finished. The Speakerphone led ❷ will be off. INCOMING CALL 4.
♦ ♦ Press HOLD button. A long beep is generated. The Speakerphone led ❷ flashes. To retrieve the call, just press the HOLD key again HOLD TRANSFER 6. A call can be placed on hold and pick up at a parallel phone. If the call is not picked up, the phone will release the line after 60s. 6.1. ♦ ♦ ♦ Press HOLD button. A long beep is generated. The Speakerphone led ❷ flashes Replace the handset on cradle. The Speakerphone led ❷ flashes rapidly. Pick up the line at a parallel phone.
♦ ♦ ♦ During conversation, receive volume can be adjusted with the + and – buttons. The + button increases receive volume by one step, while the – button decreases receive volume by one step. There are 4 levels for handset mode, and 8 levels for handsfree mode. After a call is terminated, the volume setting will revert back to default value. Handset and handsfree receive volume are independent of each other. DATA PORT 8.
9.4. ♦ ♦ ♦ • • Press HOLD Press FLASH Press: • 1 for 100 ms • 3 for 300 ms • 6 for 600 ms Press HOLD again A long beep is generated to confirm Flash Timing is programmed. 9.5. ♦ ♦ ♦ ♦ ♦ Setting Flash Timing Setting Melody Press HOLD Press RD Press: • 1 to select pitch 1, pitch 1 has a higher frequency • 2 to select pitch 2, pitch 2 has a lower frequency Press HOLD again A long beep is generated . 9.6. Exiting manual programming mode ♦ To exit manual programming mode, just hang up.
ALCATEL 2315 2315 Hotel set The manufacturer reserves the right to modify any product characteristics without prior notice.