User's Manual

ManualsBrandsAlcatel-Lucent USA ManualsElectronicsUMTS-CDMA Transceiver System (850)

1-26

Lucent Technologies – Proprietary

See notice on first page

401-703-454

FOA Draft Issue 1

January, 2006

...........................................................................................................................................................................................................................................................

Overview of the Flexent‚ Modular Cell 4.0B cabinet

installation

JUMPER CABLE

SUPPORT STRUCTURE

ASSEMBLY

(BY CUSTOMER)

2" CONDUIT

ASSEMBLYFOR

T1/E1 AND USER

ALARMS ( TYP )

ANTENNA

JUMPER CABLES

( TYP )

RF ANTENNA CABLES TO

ANTENNA TOWER ( TYP )

7/16" DIN FEMALE

CONNECTORS ( TYP )

2" CONDUIT ASSEMBLY

FOR AC POWER ( TYP )

REAR

MOUNTING BASE ( TYP )

( OPTIONAL )

PLATFORM

(BY CUSTOMER)

WNG. BATTERY CABINET 1 *

(OPTIONAL)

WNG. BATTERY CABINET 2 *

(OPTIONAL)

1 " OPTIONAL PORTS

FOR ALARMS

CABINET 1

CABINET 2

GPS ANTENNA CABLE

GPS SURGE

PROTECTION

SURGE PROTECTION (TYP)

2" CONDUIT ASSEMBLY

FOR AC POWER ( TYP )

- EZBFo #1 - EZBFo - #2 or EZBFo #2 - EZBFo - #1 - Primary 4.0B -

Dual Band 4.0B - EZBFo #1 - EZBFo - #2

Modular Cell 4.0B cabinet

side view 1

Illustrated below is an outdoor site with antenna and T1/E1 routing at

the top rear of the cabinet. The figure shows a side view of the Modular

Cell 4.0B cabinet with a sound muffler and front heat exchanger. Note

Summary of content (6 pages)

PAGE 1
Overview of the Flexent‚ Modular Cell 4.0B cabinet installation - EZBFo #1 - EZBFo - #2 or EZBFo #2 - EZBFo - #1 - Primary 4.0B Dual Band 4.0B - EZBFo #1 - EZBFo - #2 WNG. BATTERY CABINET 2 * (OPTIONAL) WNG.
PAGE 2
Overview of the Flexent‚ Modular Cell 4.0B cabinet installation the fact that a junction box may be installed, where noted, to facilitate routing of AC to a second cabinet. SIDE VIEW 1 (4.0B) NOTE: THE OPTIONAL REAR HEAT EXCHANGER IS NOT ILLUSTRATED IN THIS VIEW. IT IS PART OF THE LUCENT EQUIPMENT Modular Cell 4.0B cabinet side view 2 Illustrated below is an outdoor site with antenna and T1/E1 routing from the bottom to the top rear of the cabinet. The cabinet is illustrated with a rear heat exchanger.
PAGE 3
Overview of the Flexent‚ Modular Cell 4.0B cabinet installation illustrates the mutually exclusive optional front heat exchanger. Note the fact that a junction box may be installed, where noted, to facilitate routing of AC to a second cabinet. SIDE VIEW 2 (4.0B) N O C P T E R C U R O B P B (E T V O R R U D T S 1 P M J ( 2 C -IN E L F B N D E A R C O H IQ L B X T )P X A / (1 S U G -T ID N O C E L )L -C 2 D E S T H IN U G A ) L T A L U D IM -P 2 O C E R IX B Y .
PAGE 4
Overview of the Flexent‚ Modular Cell 4.0B cabinet installation Torque requirements ............................................................................................................................................................................................................................................................. Overview Torque requirements for mechanical connections This section provides mechanical torque requirements. Refer to the table below.
PAGE 5
Overview of the Flexent‚ Modular Cell 4.0B cabinet installation Torque specifications for electrical connections Important! The table below must not be used for spanner head self-tapping screws, in or on cabinets. It is to be used exclusively for electrical connections. Refer to the previous table for mechanical connections. The table below identifies the torque requirements to be followed when making electrical connections. Torque - in.-lb. [or ft.-lb.
PAGE 6
Overview of the Flexent‚ Modular Cell 4.0B cabinet installation Tools, supplies, and parts required (master list) ............................................................................................................................................................................................................................................................. Overview Tools This section provides a master list of all tools, materials, and parts required during the installation process.