7368 ISAM ONT G-120W-F Product Guide R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2017 Nokia.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Preface 1 Preface This preface provides general information about the documentation set for optical network terminals (ONTs). 1.1 Scope This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release. 1.
R05.06.01 | June 2017 | Edition 01 Preface 7368 ISAM ONT G-120W-F Product Guide 1.6 Nokia quality processes Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 2 Preface To access individual documents Individual PDFs of customer documents are also accessible through the Nokia Customer Support website. 1.9 1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. 2 From the Technical Content for drop-down menu, choose the product.
R05.06.01 | June 2017 | Edition 01 Preface 7368 ISAM ONT G-120W-F Product Guide 1.9.1 Procedures with options or substeps When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals. Procedure 3 Example of options in a procedure At step 1, you can choose option a or b. At step 2, you must do what the step indicates. 1 2 Procedure 4 This step offers two options.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 1.10 Preface Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note — The PDF files in which you search must be in the same folder.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Table of contents 1 Preface.............................................................................................3 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.9.1 1.10 Scope ..........................................................................................................3 Audience......................................................................................................3 Required knowledge......................
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 10 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 ONT environmental requirements .............................................................30 Storage ......................................................................................................30 Transportation ...........................................................................................30 Stationary use............................................................
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Issue: 01 5.10 5.10.1 5.11 5.11.1 5.11.1.1 5.11.1.2 5.11.1.3 5.11.2 G-120W-F standards compliance..............................................................61 Energy-related products standby and off modes compliance....................62 G-120W-F special considerations .............................................................62 Wi-Fi service......................................................................................
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide List of figures 2 ETSI ONT safety guidelines .........................................................17 Figure 1 Figure 2 Figure 3 Figure 4 PSE certification ........................................................................................19 Laser product label ....................................................................................22 Laser classification label....................................................
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 70 Figure 71 Figure 72 Figure 73 Figure 74 14 WAN network window...............
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide List of tables 2 ETSI ONT safety guidelines .........................................................17 Table 1 Safety labels ..............................................................................................18 4 ANSI ONT safety guidelines ........................................................33 Table 2 Safety labels ..............................................................................................
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Table 38 Table 39 Table 40 Table 41 Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 Table 51 Table 52 16 Access control parameters ......................................................................116 Port forwarding parameters .....................................................................118 Port triggering parameters.......................................................................
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ETSI ONT safety guidelines 2 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 2.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 2.1.
R05.06.01 | June 2017 | Edition 01 ETSI ONT safety guidelines 7368 ISAM ONT G-120W-F Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 1 ETSI ONT safety guidelines PSE certification This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Warning 19841 2.
R05.06.01 | June 2017 | Edition 01 ETSI ONT safety guidelines 2.2.3 7368 ISAM ONT G-120W-F Product Guide Environmental standard compliance The ONT equipment complies with the EN 300 019 European environmental standards. 2.2.4 Laser product standard compliance For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 2.3.1 ETSI ONT safety guidelines Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 2.3.
R05.06.01 | June 2017 | Edition 01 ETSI ONT safety guidelines 7368 ISAM ONT G-120W-F Product Guide Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system. Danger — There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam. Observe the following danger for laser hazard.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 3 ETSI ONT safety guidelines Laser classification label CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 4 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages.
R05.06.01 | June 2017 | Edition 01 ETSI ONT safety guidelines Figure 4 7368 ISAM ONT G-120W-F Product Guide Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 2.5.4 ETSI ONT safety guidelines Location class Use cable supports and guides to protect the receptacles from strain. 2.6 Environmental requirements See the ONT technical specification documentation for more information about temperature ranges. During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ETSI environmental and CRoHS guidelines 3 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. 3.
R05.06.01 | June 2017 | Edition 01 ETSI environmental and CRoHS guidelines Figure 5 7368 ISAM ONT G-120W-F Product Guide Products below MCV value label 18986 3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 6 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products).
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 6 ETSI environmental and CRoHS guidelines Products above MCV value label 18985 Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.
R05.06.01 | June 2017 | Edition 01 ETSI environmental and CRoHS guidelines 3.3 7368 ISAM ONT G-120W-F Product Guide Other environmental requirements Observe the following environmental requirements when handling the P-OLT or ONT equipment. 3.3.1 ONT environmental requirements See the ONT technical specification documentation for more information about temperature ranges. 3.3.2 Storage According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in Class 1.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 3.3.6 ETSI environmental and CRoHS guidelines Material content compliance European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment.
R05.06.01 | June 2017 | Edition 01 ETSI environmental and CRoHS guidelines 7368 ISAM ONT G-120W-F Product Guide At the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE). There can be different requirements for collection and treatment in different member states of the European Union.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ANSI ONT safety guidelines 4 ANSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market. 4.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 4.1.
R05.06.01 | June 2017 | Edition 01 ANSI ONT safety guidelines 7368 ISAM ONT G-120W-F Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ANSI ONT safety guidelines Description Label text Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
R05.06.01 | June 2017 | Edition 01 ANSI ONT safety guidelines 4.2.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 4.2.
R05.06.01 | June 2017 | Edition 01 ANSI ONT safety guidelines 4.2.5 7368 ISAM ONT G-120W-F Product Guide Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to overvoltage and overcurrents. 4.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 10 ANSI ONT safety guidelines Laser product label 18455 Figure 11 shows a laser classification label. Laser classification labels may be provided in other languages. Figure 11 Laser classification label CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 12 shows a laser warning label and an explanatory label for laser products.
R05.06.01 | June 2017 | Edition 01 ANSI ONT safety guidelines Figure 12 7368 ISAM ONT G-120W-F Product Guide Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 13 ANSI ONT safety guidelines Sample laser product safety label on the ONT equipment Model: MFG: MONTH: XX YEAR: XXXX ICS: XX MRev: XX 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX I.T.E FCC ID: XXXXXXXXXXX 12VDC 3A ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 Intertek 4006119 This device complies with Part 15 of the FCC Rule.
R05.06.01 | June 2017 | Edition 01 ANSI ONT safety guidelines 4.4 7368 ISAM ONT G-120W-F Product Guide Electrical safety guidelines This section provides the electrical safety guidelines for the ONT equipment. Note — The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. 4.4.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ANSI ONT safety guidelines During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD. Nokia recommends that you prepare the site before you install the ONT equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning. 4.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide G-120W-F unit data sheet 5 G-120W-F unit data sheet 5.1 G-120W-F part numbers and identification 5.2 G-120W-F general description 5.3 G-120W-F software and installation feature support 5.4 G-120W-F interfaces and interface capacity 5.5 G-120W-F LEDs 5.6 G-120W-F detailed specifications 5.7 G-120W-F GEM ports and T-CONTs 5.8 G-120W-F performance monitoring statistics 5.9 G-120W-F functional blocks 5.10 G-120W-F standards compliance 5.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet 5.1 7368 ISAM ONT G-120W-F Product Guide G-120W-F part numbers and identification Table 3 provides part numbers and identification information for the G-120W-F indoor ONT.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide G-120W-F unit data sheet For the G-120W-F indoor ONT power supply information, contact your Nokia technical support representative. 5.2 G-120W-F general description G-120W-F indoor ONTs provide the subscriber interface for the network by terminating the PON interface and converting it to user interfaces that directly connect to subscriber devices.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet 5.2.1 7368 ISAM ONT G-120W-F Product Guide TR-069 support The ONT supports the reading of optical parameters via TR-069: • • • • • laser bias current voltage temperature received signal levels lower thresholds These are the same optical parameters supported in the GUI. For more information, see Table 21 in the chapter “Configure a G-120W-F indoor ONT”.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide G-120W-F unit data sheet The following TR-181 Wi-Fi objects (and sub-objects) adapted in TR-098 are supported in this release: • • • • • • • • • • • • • • • • • 5.2.4 Device.WiFi Device.WiFi.Radio.{i}. Device.WiFi.Radio.{i}.Stats. Device.WiFi.SSID.{i}. Device.WiFi.SSID.{i}.Stats. Device.WiFi.AccessPoint.{i}. Device.WiFi.AccessPoint.{i}.Security. Device.WiFi.AccessPoint.{i}.WPS. Device.WiFi.AccessPoint.{i}.AssociatedDevice{i}.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet 5.2.5 7368 ISAM ONT G-120W-F Product Guide Bridged Residential Gateway (BRG) support The BRG receives IP addresses for the WAN interface using DHCP or PPPoE. The BRG can use either Ipv4 or Ipv6 addresses. BRG uses OpenFlow protocol version 1.3.1 to manage Access Control List entries and routing protocols. TR-069 can be used to manage the local DHCP server and the soft GRE tunnel.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 5.2.6.2 G-120W-F unit data sheet Soft GRE In soft GRE, only one side of the tunnel needs to be configured; the other end learns the remote IP addresses of all remote tunnel endpoints by examining the incoming GRE packets. GRE tunnels can be automatically created when devices attach to the AP, eliminating the need for each AP to be explicitly provisioned on the WLAN Gateway.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet 5.3 7368 ISAM ONT G-120W-F Product Guide G-120W-F software and installation feature support For information on installing or replacing the G-120W-F see: • Install a G-120W-F indoor ONT • Replace a G-120W-F indoor ONT For information on the following topics, see the 7368 ISAM ONT Product Overview Guide: • • • • • • • • 5.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 15 G-120W-F unit data sheet G-120W-F indoor ONT physical connections Antenna GPON Fiber connection TEL Antenna LAN2 POTS port LAN1 Ethernet Ports (2) POWER Power input RESET WLAN Reset ONT WPS LED ON/OFF Wireless WPS LEDs ONT on/off on/off on/off on/off 26048 Table 5 describes the physical connections for G-120W-F indoor ONTs.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet 5.5 7368 ISAM ONT G-120W-F Product Guide G-120W-F LEDs Figure 16 shows the G-120W-F indoor ONT LEDs. Figure 16 G-120W-F indoor ONT LEDs POWER POWER LINK LINK AUTH AUTH LAN1 LAN2 LAN1 LAN2 TEL TEL VOIP WPS VOIP WLAN INTERNET WPS WLAN INTERNET 26049 Table 6 provides LED descriptions for G-120W-F indoor ONTs.
R05.06.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet Table 9 7368 ISAM ONT G-120W-F Product Guide G-120W-F indoor ONT environmental specifications Temperature range and humidity Altitude Operating: 23°F to 113 F (-5°C to 45°C) ambient temperature Contact your Nokia technical support representative for more information 5% to 95% relative humidity, non-condensing Storage: -4°F to 158°F (-20°C to 70C) 5.
R05.06.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet RXFRAGS LOSTFRAGS ✓ ✓ ✓ ✓ ✓ BADGEMHDRS RXBLOCKS G-120W-F (1) PONONTTC (aggregate) statistics TXFRAGS ONT Package S ONTs PONONTTC aggregate performance monitoring statistics TXBLOCKS Table 14 7368 ISAM ONT G-120W-F Product Guide Note (1) 5.
R05.06.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet Figure 18 7368 ISAM ONT G-120W-F Product Guide G-120W-F ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON 19421 ONT SoC technology consists of five key elements: • GPON MAC • • • • 60 The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide G-120W-F unit data sheet These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology. 5.10 G-120W-F standards compliance G-120W-F indoor ONTs are compliant with the following standards: • • • • • • • • • • • • • • • 802.1p QoS 802.1q VLANs 802.3 auto negotiation, flow control 802.11 b/g/n at 2.4 GHz Codec G.711 a/u, G.722, G.723, G.726, G.729 EN 300-328 v1.9.
R05.06.01 | June 2017 | Edition 01 G-120W-F unit data sheet Figure 20 5.10.1 7368 ISAM ONT G-120W-F Product Guide G-120W-F ONT safety label Energy-related products standby and off modes compliance Hereby, Nokia declares that the G-120W-F ONTs are in compliance with the essential requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 5.11.1.1 G-120W-F unit data sheet Wi-Fi physical features G-120W-F indoor ONTs have the following physical features that assist in providing Wi-Fi service: • WLAN button for enabling and disabling Wi-Fi service • two external multi-directional antennae • Wi-Fi Protected Setup (WPS) push button for enabling and disabling wireless protective services 5.11.1.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Install a G-120W-F indoor ONT 6 Install a G-120W-F indoor ONT 6.1 Purpose 6.2 General 6.3 Prerequisites 6.4 Recommended tools 6.5 Safety information 6.6 Procedure 6.1 Purpose This chapter provides the steps to install a G-120W-F indoor ONT. 6.2 General The steps listed in this chapter describe mounting and cabling for G-120W-F indoor ONTs. 6.
R05.06.01 | June 2017 | Edition 01 Install a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide • drill and drill bits • paper clip 6.5 Safety information Read the following safety information before installing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 6.6 Install a G-120W-F indoor ONT Procedure Use this procedure to install a G-120W-F indoor ONT. 1 Place the indoor ONT unit: a On the flat surface, such as a desk or shelf; go to step 3. Note — The G-120W-F cannot be stacked with another ONT or with other equipment.
R05.06.01 | June 2017 | Edition 01 Install a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide The recommended length of mounting screw is 1.15 in. (3.8 cm). Do not drive the screw into the wall completely. Leave approximately 1/8 in. (6 mm) between the screw head and the wall surface. iv 3 Slide the wall mount keyholes on the ONT enclosure down over the mounting screws until the ONT is securely seated. Review the connection locations as shown in Figure 22.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Install a G-120W-F indoor ONT Note — Fiber cable preparation varies depending on the type and size of the inside or outside plant fiber cable being spliced to the SC/APC (SC/UPC) fiber optic pigtail cable. 7 Install the power supply according to manufacturer specifications. Note — Observe the following: • 8 Connect the power cable to the power connector. 9 Power up the ONT unit by using the power on/off switch.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Replace a G-120W-F indoor ONT 7 Replace a G-120W-F indoor ONT 7.1 Purpose 7.2 General 7.3 Prerequisites 7.4 Recommended tools 7.5 Safety information 7.6 Procedure 7.1 Purpose This chapter provides the steps to replace G-120W-F indoor ONTs. 7.2 General The steps listed in this chapter describe mounting and cabling for G-120W-F indoor ONTs. 7.
R05.06.01 | June 2017 | Edition 01 Replace a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide • optical power meter • drill and drill bits 7.5 Safety information Read the following safety information before replacing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 7.6 Replace a G-120W-F indoor ONT Procedure Use this procedure to replace a G-120W-F indoor ONT. 1 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). i Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output.
R05.06.01 | June 2017 | Edition 01 Replace a G-120W-F indoor ONT 5 7368 ISAM ONT G-120W-F Product Guide Disconnect the fiber optic cable. Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. 6 i Unplug the fiber optic cable with SC/APC connector from the fiber optic port. ii Attach a fiber dust cover to the end of the SC/APC (SC/UPC) connector.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 11 Replace a G-120W-F indoor ONT Install the power supply according to manufacturer specifications. Note — Observe the following: • Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A. 12 Connect the power cable to the power connector. 13 Power up the unit by using the on/off power switch.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT 8 Configure a G-120W-F indoor ONT 8.1 General 8.2 HGU mode GUI configuration 8.3 SFU mode GUI configuration 8.4 Operator ID 8.1 General Please refer to the configuration information provided with your OLT for the software configuration procedure for a G-120W-F ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 8.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide The default gateway IP address is http://192.168.1.254. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same subnet as the ONT. 2 Enter your username and password in the Log in window, as shown in Figure 24. The default user name is userAdmin.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT • optics module status • statistics • voice information Procedure 7 Device information retrieval 1 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 25. Figure 25 Device Information window Table 16 describes the fields in the Device Information window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide Field Description Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds (2 of 2) 80 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 8 Configure a G-120W-F indoor ONT LAN status retrieval 1 Select Status > LAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 26. Figure 26 LAN status window Table 17 describes the fields in the LAN status window.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Procedure 9 WAN status retrieval 1 Select Status > WAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 27. Figure 27 WAN status window Table 18 describes the fields in the WAN status window.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 10 Configure a G-120W-F indoor ONT WAN status IPv6 retrieval 1 Select Status > WAN Status IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 28. Figure 28 WAN status IPv6 window Table 19 describes the fields in the WAN status IPv6 window. Table 19 WAN status IPv6 parameters Field Description WAN connection list Drop-down menu listing all WAN connections.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 11 Configure a G-120W-F indoor ONT Home networking information retrieval 1 Select Status > Home Networking from the top-level menu in the GPON Home Gateway window, as shown in Figure 29. Figure 29 Home networking information window Table 20 describes the fields in the Home networking window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide 3 Click Refresh to update the displayed information. 4 STOP. This procedure is complete. Procedure 12 Optics module status retrieval 1 Select Status > Optics Module Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 30. Figure 30 Optics module status window Table 21 describes the fields in the Optics module status window.
R05.06.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide If there are no WAN connections to display, the system displays a message to indicate that. 2 Procedure 14 STOP. This procedure is complete. Voice information retrieval 1 Select Status > Voice Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 32. Figure 32 Voice Information window Table 22 describes the fields in the Voice Information window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT Field Description Register Error Reason Error reason for the unregistered POTS port User Agent IP IP address of the user agent (2 of 2) Note (1) This field is only visible at the adminGPON level; it is not visible at the userAdmin level. 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. 8.2.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 15 7368 ISAM ONT G-120W-F Product Guide LAN networking configuration 1 Select Network > LAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 33. Figure 33 LAN network window Table 23 describes the fields in the LAN network window.
R05.06.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 16 7368 ISAM ONT G-120W-F Product Guide LAN IPv6 networking configuration 1 Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 34. Figure 34 LAN IPv6 network window Table 24 describes the fields in the LAN IPv6 network window. Table 24 LAN IPv6 network parameters Field Description DNS Server Choose a DNS server from the drop-down menu.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT Field Description Whether other info obtained through DHCP Select this checkbox to enable retrieval of other information through DHCP. Maximum interval for periodic RA messages Enter the maximum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 17 7368 ISAM ONT G-120W-F Product Guide WAN networking configuration 1 Select Network > WAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 35. Figure 35 WAN network window Table 25 describes the fields in the WAN network window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT Field Description Manual DNS Enter a manual DNS (2 of 2) 2 Configure a specific WAN connection. 3 Click Save. 4 STOP. This procedure is complete. Procedure 18 WAN DHCP configuration 1 Select Network > WAN DHCP from the top-level menu in the GPON Home Gateway window, as shown in Figure 36. Figure 36 WAN DHCP window Table 26 describes the fields in the WAN DHCP window.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 19 Configure a G-120W-F indoor ONT Wireless 2.4GHz networking configuration 1 Select Network > Wireless 2.4GHz from the top-level menu in the GPON Home Gateway window, as shown in Figure 37. Figure 37 Wireless 2.4GHz network window Table 27 describes the fields in the Wireless 2.4GHZ network window. Table 27 WiFi 2.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide (2) Configure a G-120W-F indoor ONT When Encryption Mode is set to “WPA/WPA2 Enterprise”, the following options become available: Primary RADIUS server, port and password; Secondary RADIUS server, port, and password; RADIUS accounting port. 2 Configure the WiFi connection. 3 If you have enabled and configured WPS, click WPS connect. 4 Click Save. 5 STOP. This procedure is complete.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide 4 Enter a start time and end time for the period in which you want the wireless signal off. 5 Choose Everyday or Individual Days from the drop-down menu. 6 If you chose Individual Days, select the checkboxes for the desired days. The Recurrence Pattern shows the rules created to date. 7 If desired, click the plus sign (+) to add more rules. 8 Click Save Changes. 9 STOP.
R05.06.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 22 7368 ISAM ONT G-120W-F Product Guide DNS configuration 1 Select Network > DNS from the top-level menu in the Home Gateway window, as shown in Figure 40. Figure 40 DNS network window Table 29 describes the fields in the DNS network window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT 4 If required, associate an original domain with a new domain, click Add. 5 STOP. This procedure is complete. Procedure 23 TR-069 configuration 1 Select Network > TR-069 from the top-level menu in the GPON Home Gateway window, as shown in Figure 41. Figure 41 TR-069 network window Table 30 describes the fields in the TR-069 network window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide Field Description Connect Request Password Password used to log in to the auto-configuration server (2 of 2) 2 Configure TR-069 by entering the required information. 3 Click Save. 4 STOP. This procedure is complete. Procedure 24 QoS configuration 1 Select Network > QoS Config from the top-level menu in the Home Gateway window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Table 31 Configure a G-120W-F indoor ONT QoS Config parameters Field Description Type Choose a QoS service layer type from the drop-down menu L2 or L3. Source MAC Enter the source MAC. Select the Exclude checkbox to exclude the source MAC Interface Choose an interface from the drop-down menu 802.1p Mark Enter the value for the 802.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide • parental control • DMZ and ALG • access control Procedure 25 Firewall configuration 1 Select Security > Firewall from the top-level menu in the GPON Home Gateway window, as shown in Figure 43. Figure 43 Firewall window Firewall security applies only to services provided by the ONT. Internet access from the LAN side is not affected by this firewall.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Table 32 Configure a G-120W-F indoor ONT Firewall parameters Field Description Security level Choose the security level from the drop-down menu: low, medium, or high Attack Protect (Protection against DoS or DDoS attacks) Choose enable or disable attack protect from the drop-down menu The default is disable 2 Configure the firewall. 3 Click Save. 4 STOP. This procedure is complete.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Table 33 7368 ISAM ONT G-120W-F Product Guide MAC filter parameters Field Description Enable MAC filter Select this checkbox to enable the MAC filter Mac Address Select a MAC address from the drop-down menu or enter the address in the text field Mac Filter Mode Choose the MAC filter mode from this drop-down menu: Blocked or Allowed 2 Click Refresh to update the information. 3 Configure a MAC filter. 4 Click Add. 5 STOP.
R05.06.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 28 7368 ISAM ONT G-120W-F Product Guide URL filter configuration 1 Select Security > URL Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 46. Figure 46 URL Filter window Table 35 describes the fields in the URL Filter window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT You can configure up to 100 URL filters. 5 STOP. This procedure is complete. Procedure 29 Parental control 1 Select Security > Parent Control from the top-level menu in the EPON Home Gateway window, as shown in Figure 47. Figure 47 Parental Control window Table 36 describes the fields in the Parental Control window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide 2 Select the Access Control checkbox. 3 Click the plus sign (+) to add a policy. A separate panel displays for configuring the policy name, IP address of the device, and dates and times for the policy. 4 Configure the parental control policy. 5 Click Enable to activate the policy. 6 STOP. This procedure is complete.
R05.06.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 31 7368 ISAM ONT G-120W-F Product Guide Access control configuration This procedure describes how to configure the access control level (ACL). Note 1 — ACL takes precedence over the firewall policy. Note 2 — The trusted network object will be shared for all WAN connections; it is not applied individually to a WAN connection.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT Field Description Source IP End Enter an end IP address for the new subnet trusted network (2 of 2) 2 Select a WAN connection from the drop-down menu. 3 Click to enable or disable Trusted Network. 4 Select an access control level for each of the seven protocols for both the WAN and the LAN side. 5 Click Save. 6 Optionally, add one or more subnet trusted networks.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 32 7368 ISAM ONT G-120W-F Product Guide Port forwarding configuration 1 Select Application > Port forwarding from the top-level menu in the GPON Home Gateway window, as shown in Figure 50. Figure 50 Port forwarding window Table 39 describes the fields in the port forwarding window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT 3 Click Add. 4 STOP. This procedure is complete. Procedure 33 Port triggering 1 Select Application > Port Triggering from the top-level menu in the GPON Gateway window, as shown in Figure 51. Figure 51 Port Triggering window Table 40 describes the fields in the Port Triggering window.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT Table 41 describes the fields in the DDNS window. Table 41 Field Description WAN Connection List Choose a WAN connection from the drop-down menu Enable DDNS Select this checkbox to enable DDNS on the chosen WAN connection ISP Choose an ISP from the drop-down menu. Domain Name Domain name Username Username Password Password 2 Configure the DDNS. 3 Click Save. 4 STOP.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 2 Select the Enable NTP Service checkbox to enable NTP service. 3 Click Save. 4 STOP. This procedure is complete. Procedure 36 UPnP and DLNA configuration 1 Select Application > UPnP and DLNA from the top-level menu in the GPON Home Gateway window, as shown in Figure 54. Figure 54 122 7368 ISAM ONT G-120W-F Product Guide UPnP and DLNA window 2 Select the Enable UPnP/DLNA checkbox to enable UPnP and DLNA. 3 Click Save/Apply.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 37 Voice setting 1 Select Application > Voice Setting from the top-level menu in the EPON Home Gateway window, as shown in Figure 55.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide Table 42 describes the fields in the Voice Setting window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide • • • • • • Procedure 38 Configure a G-120W-F indoor ONT backup and restore upgrade firmware reboot device restore factory defaults diagnose WAN connections log Password configuration 1 Select Maintenance > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 56. Figure 56 Password window Table 43 describes the fields in the password window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 39 WAN speed test 1 Select Maintenance > Speed Test from the top-level menu in the GPON Home Gateway window, as shown in Figure 57. Figure 57 2 Speed Test window Click Start to start the speed test. Enter the URL for the test server in the pop-up window. 3 126 STOP. This procedure is complete.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 40 Configure a G-120W-F indoor ONT LOID configuration 1 Select Maintenance > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 58. Figure 58 LOID Config window Table 44 describes the fields in the LOID configuration window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 41 7368 ISAM ONT G-120W-F Product Guide SLID configuration 1 Select Maintenance > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 59. Figure 59 SLID configuration window Table 45 describes the fields in the SLID configuration window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT 3 Click Save. 4 STOP. This procedure is complete. Procedure 42 Device management 1 Select Maintenance > Device Management from the top-level menu in the GPON Home Gateway window, as shown in Figure 60. Figure 60 Device management window Table 46 describes the fields in the Device management window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 3 Click Add. 4 STOP. This procedure is complete. Procedure 43 Backup and restore 1 Select Maintenance > Backup and Restore from the top-level menu in the GPON Home Gateway window, as shown in Figure 61. Figure 61 130 7368 ISAM ONT G-120W-F Product Guide Backup and Restore window 2 Click Choose File and choose the backup file.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 44 Upgrade firmware 1 Select Maintenance> Firmware Upgrade from the top-level menu in the GPON Home Gateway window, as shown in Figure 62. Figure 62 Issue: 01 Configure a G-120W-F indoor ONT Firmware upgrade window 2 Click Choose File and choose the firmware file. 3 Click Upgrade to upgrade the firmware. 4 STOP. This procedure is complete.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 45 Reboot ONT 1 Select Maintenance > Reboot Device from the top-level menu in the GPON Home Gateway window, as shown in Figure 63. Figure 63 132 7368 ISAM ONT G-120W-F Product Guide Reboot window 2 Click Reboot to reboot the ONT. 3 STOP. This procedure is complete.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 46 Restore factory defaults 1 Select Maintenance > Factory Default from the top-level menu in the GPON Home Gateway window, as shown in Figure 64. Figure 64 Issue: 01 Configure a G-120W-F indoor ONT Factory default window 2 Click Factory Default to reset the ONT to its factory default settings. 3 STOP. This procedure is complete.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 47 7368 ISAM ONT G-120W-F Product Guide Diagnose WAN connections 1 Select Maintenance > Diagnostics from the top-level menu in the GPON Home Gateway window, as shown in Figure 65. Figure 65 Diagnostics window 2 Choose a WAN connection to diagnose from the drop-down menu. 3 Enter the IP address or domain name. 4 Select the test type: ping, traceroute, or both.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 9 Click Cancel to cancel the test. 10 STOP. This procedure is complete. Procedure 48 View log files 1 Select Maintenance > Log from the top-level menu in the GPON Home Gateway window, as shown in Figure 66.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 3 7368 ISAM ONT G-120W-F Product Guide Choose a reading level from the drop-down menu to determine which types of events to display from the log file: • • • • • • • • Emergency Alert Critical Error Warning Notice Informational Debug 4 The log file is displayed in the bottom panel of the window. 5 STOP. This procedure is complete. 8.2.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Figure 67 Configure a G-120W-F indoor ONT RG Troubleshooting Counters window Table 47 describes the fields in the RG Troubleshooting Counters window.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 2 Configure a G-120W-F indoor ONT Enter your username and password in the Log in window, as shown in Figure 68. The default username is adminadmin. The default password is ALC#FGU. Figure 68 Web login window Caution — Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 51 7368 ISAM ONT G-120W-F Product Guide Device information retrieval 1 Select Status > Device Information from the top-level menu in the SFU GPON Home Gateway window, as shown in Figure 69. Figure 69 Device Information window Table 48 describes the fields in the Device Information window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Configure a G-120W-F indoor ONT 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Procedure 52 Optics module status retrieval 1 Select Status > Optics Module Status from the top-level menu in the SFU GPON Home Gateway window, as shown in Figure 70. Figure 70 Optics module status window Table 49 describes the fields in the Optics module status window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT 7368 ISAM ONT G-120W-F Product Guide Field Description Lower (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Lower optical threshold, measured in dBm Upper (ONT ANI-ONT-Side Optical Measurements-Optical Threshold) Lower optical threshold, measured in dBm (2 of 2) 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. 8.3.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide 3 Configure a G-120W-F indoor ONT Click the plus sign (+) to add a scheduling rule. A separate panel displays for configuring wireless schedule rules. 4 Enter a start time and end time for the period in which you want the wireless signal off. 5 Choose Everyday or Individual Days from the drop-down menu. 6 If you chose Individual Days, select the checkboxes for the desired days.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 54 7368 ISAM ONT G-120W-F Product Guide Password configuration 1 Select Maintenance > Password from the top-level menu in the SFU GPON Home Gateway window, as shown in Figure 72. Figure 72 Password window Table 50 describes the fields in the password window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 55 Configure a G-120W-F indoor ONT LOID configuration 1 Select Maintenance> LOID Config from the top-level menu in the SFU GPON Home Gateway window, as shown in Figure 73. Figure 73 LOID Authentication window Table 51 describes the fields in the LOID configuration window.
R05.06.01 | June 2017 | Edition 01 Configure a G-120W-F indoor ONT Procedure 56 7368 ISAM ONT G-120W-F Product Guide SLID configuration 1 Select Maintenance > SLID Configuration from the top-level menu in the SFU GPON Home Gateway window, as shown in Figure 74. Figure 74 SLID configuration window Table 52 describes the fields in the SLID configuration window.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide Procedure 57 Configure a G-120W-F indoor ONT Modifying the operator ID 1 Register the ONT with the OLT. 2 Check the original OPID. 3 Update the OntConfig.xml file by adding-the following content: where: xxxx is the correct operator ID, for example ALCL for HGU mode, or XXXX for SFU mode. 4 Use a TFTP client tool to transfer the OntConfi.
R05.06.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ONT configuration file over OMCI 9 ONT configuration file over OMCI 9.1 Purpose 9.2 Supported configuration file types 9.3 ONT configuration file over OMCI 9.1 Purpose This procedure describes how to use configuration files over OMCI to configure ONTs.
R05.06.01 | June 2017 | Edition 01 ONT configuration file over OMCI Table 53 7368 ISAM ONT G-120W-F Product Guide Supported configuration files File Index Description Details Supported ONTs/DPU PRE ONT pre-configuration file The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ONT configuration file over OMCI File Index Description Details Supported ONTs/DPU GFT G.fast-related configuration file This text-based json script file controls the default behavior of the G.Fast ONT. HGU ONTs: G-120G-E, G-120W-F, G-240G-C, G-240W-B, G-240W-C, I-240W-A This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning.
R05.06.01 | June 2017 | Edition 01 ONT configuration file over OMCI Procedure 58 7368 ISAM ONT G-120W-F Product Guide Configuring an ONT using a configuration file via OMCI 1 Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Nokia, generate the TAR file as follows: i On a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 9.2. ii Tar the ABCXXXXVER raw configuration file: tar -cf ABCXXXXVER.
R05.06.01 | June 2017 | Edition 01 7368 ISAM ONT G-120W-F Product Guide ONT configuration file over OMCI FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. iv If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same.
R05.06.
R05.06.
R05.06.01 | June 2017 | Edition 01 Copyright 2017 Nokia.