Appendix 2 – Climatic areas world map 3CC12425AAAA TQ BJA 01 Issue 01 - April 2001 - Draft 03 59/70 60
PAGE INTENTIONALLY LEFT BLANK 60/70 60 Issue 01 - April 2001 - Draft 03 3CC12425AAAA TQ BJA 01
Appendix 3 – Mounting coaxial connectors for 5916 CommScope 3CC12425AAAA TQ BJA 01 Issue 01 - April 2001 - Draft 03 61/70 66
62/70 66 Issue 01 - April 2001 - Draft 03 3CC12425AAAA TQ BJA 01
A.3.1 – Installing Stirling connectors This section describes how to install a Stirling connector on CommScope RG-type cable. A.3.1.1 – To install a Stirling connector To prevent damage to the center pin of the connector, keep the cap on the connector during installation unless specified otherwise.
Figure 31 – Exposing the shield and center conductor 5. Pull the braided shielding back over the jacket and inspect the exposed end. Ensure that it is clean (free of loose pieces of shielding). 6. Attach the Stirling connector. • To attach an SPP-6-0 or SPP-59-0 connector, carefully insert the cable into the connector until you feel the cable click into place. Do not try to remove the connector after it has been put on the cable.
• Position the center conductor at the second line on the stripper/activator tool and mark the cable jacket with your thumbnail at the base of the activator; see Figure 33. Mark jackethere Second line Figure 33 – Measuring and marking the 5916 cable • Carefully place the connector on the cable and push the connector until it meets the thumbnail mark. If the connector is pushed too far onto the cable, it may not properly connect to its mate connector.
66/70 66 Issue 01 - April 2001 - Draft 03 3CC12425AAAA TQ BJA 01
Appendix 4 – Correspondence between commercial codes and industrial codes relating to the TS Installation item Commercial code Industrial code Comments 7390 NC - commercial NT NT unit NCA 001 (2 Eth + 2 G703) 220V 9900NCA001+ 9900SWA001 3CC 10329 AAxx without power cable NGA 001 (2 Eth + G703) 48V 9900NGA001+ 9900SWA001 3CC 10329 BCxx With cable 48V NGA 004 (2 Eth + 2G703, LEMO) 48V 9900NGA004+ 9900SWA001 3CC 10329 BFxx With cable 48V NCA 002 (2 Eth + 1G703 + X21) 220V 9900NCA002+ 9900SWA00
Installation item Commercial code Industrial code Comments IGAU I GAU 5dB 9900 XTX 006 90-8709-02 I GAU 7dB 9900 XTX 007 90-8709-03 I GAU 9dB 9900 XTX 008 90-8709-04 I GAU 11dB 9900 XTX 009 90-8709-05 68/70 68 Issue 01 - April 2001 - Draft 03 3CC12425AAAA TQ BJA 01
Appendix 5 – List of abbreviations MNEMONIC ENGLISH AAL ATM Adaptation Layer AIS Alarm Indication Signal AL Alarm AMD ATM Modulator Demodulator AMTR Antenna Misalignment Transition Radius MNEMONIC ENGLISH IBS Intermediate frequency Base Station ICS Identifier Change Status I2C or IIC Inter Integrated Circuit ID IDentifier IEC International Electrotechnical Commission IM Information Model IP Internet Protocol ISDN Integrated Services Digital Network ITR IGAU Transition Radius
MNEMONIC ENGLISH MNEMONIC ENGLISH NFS Network File System TDM Time Division Multiplex NIT Network Installation Tool TE Transaction End NRZ Non return to zero TNT TDM Network Termination NT Network Terminal TS Terminal Station OC Object Creation UNI User Network Interface OD Object Deletion VPI Virtual Path Identifier OOF Out Of Frame VCI Virtual Channel Identifier OS Operation System WAN Wide Area Network PAIS Path Alarm Indication Signal IGAU In line Gain Adjustement