Installation Instructions

ManualsBrandsAlarm Controls ManualsElectronicsElectric Door Strike

Page 1

AES-100

Electric Strike

and Technical Support

UL 1034

Grade 1

Alarm Controls

19 Brandywine Drive

Deer Park, NY 11729

800.645.5538

www.alarmcontrols.com

1-1/8"

[28.20]

9/32"

[7.0]

1-27/32"

[47.0]

1-1/2"

[38.0]

3-27/32"

[97.70]

1/8"

[3.0]

1-1/4"

[31.50]

5/8"

[15.75]

4-7/8"

[123.83]

4-1/8"

[104.78]

3-3/8"

[85.73]

3/4"

[18.90]

1-3/4"

[44.75]

1-5/32"

[29.0]

7/8"

[22.0]

11/16"

[17.50]

13/16"

[20.50]

11/32"

[8.50]

1-1/2"

[38.10]

5/8"

[15.75]

4-7/8"

[123.83]

4-1/8"

[104.78]

3-3/8"

[85.73]

3/4"

[18.90]

1-1/4"

[31.50]

5/8"

7-15/16"

[201.61]

1-1/4"

[31.50]

[15.75]

7-7/16"

[189.0]

3-3/8"

[85.20]

2-9/32"

[57.90]

DIMENSIONS

4-7/8“

SQUARE CORNER

FACE PLATE

4-7/8“

ROUND CORNER

FACE PLATE

7-15/16“

ROUND CORNER

FACE PLATE

1-1/4"

[31.50]

5/8"

[15.75]

4-7/8"

[123.83]

4-1/8"

[104.78]

3-3/8"

[85.73]

3/4"

[18.90]

Note: Drawings are not to scale. All dimensions are in inch and mm. This information is subject to change without notice.

Summary of content (4 pages)

PAGE 1
AES-100 Electric Strike Installation Instructions and Technical Support UL 1034 . Grade 1 Alarm Controls 19 Brandywine Drive Deer Park, NY 11729 800.645.5538 www.alarmcontrols.com DIMENSIONS 1-1/4" [31.50] 5/8" [15.75] 4-1/8" [104.78] 3-3/8" [85.73] 4-7/8" [123.83] 3/4" [18.90] 1-3/4" [44.75] 5/8" [15.75] 1-1/4" [31.50] 3-27/32" [97.70] 1-27/32" [47.0] 3-3/8" [85.73] 11/32" [8.50] 11/16" [17.50] 1-1/2" [38.0] 1/8" [3.0] 5/8" [15.75] 4-7/8" [123.83] 1-1/4" [31.50] 5/8" [15.75] 7-7/16" [189.
PAGE 2
INSTALLATION INSTRUCTIONS FIG. 1: DOOR JAMB DESCRIPTION 1. Prepare door jamb per appropriate template detail. 2. Install mounting tabs using #10-32 screws. Do not tighten. Set tabs for 1/8” thick face plate. CYLINDRICAL LOCKSET VERTICAL CENTERLINE STRIKE PLATE 12-24 TAP 3. Connect wires coming from the low voltage power source (see wiring diagrams and electrical specifications on page 3). STRIKE 1-1/8 [28.57] 4.
PAGE 3
RETROFIT JAMB PREPARATION TO FIND VERTICAL CENTERLINE FIG 7 When Jamb: • is not squared • is warped • has heavy weather stripping • conditions are not ideal 1. To determine the location of the Vertical Centerline of the mounting screw holes, first measure the distance from the outside face of the door to the face of the latchbolt (distance A”) “ (see FIG. 7). Door "A" Deadlatch 2. Close the door and measure the distance from the outside face of the door jamb (distance “B”) (see FIG. 8).
PAGE 4
WIRING DIAGRAMS AND GENERAL SPECIFICATIONS CAUTION! Before connecting any device at the installation site, verify input voltage and current using a multimeter. Many power supplies and transformers operate at higher levels than listed. Any input voltage exeeding 10% of solenoid rating may cause severe damage to the unit and will void the warranty. GENERAL INFORMATION This electric strike is equipped with a field selectable 12 V DC/AC and 24 V DC/AC dual voltage solenoid. 12V is preselected.