Installation Manual

ManualsBrandsAlarm Controls ManualsElectronics600 lbs Double Door Magnetic Lock with status LED, Bond Sensor and Door Status Sensor

SOLID DOOR

ALARM CONTROLS CORPORATION

19 BRANDYWINE DRIVE P.O. BOX 280

DEER PARK, NY 11729

800 645-5538 WWW.ALARMCONTROLS.COM

MAGNETIC LOCK INSTALLATION INSTRUCTIONS

ALARM CONTROLS CORPORATION OFFERS A COMPLETE LINE OF MAGNETIC LOCKS AND ACCESSORY ITEMS

TO ASSIST THE INSTALLER IN MANAGING EVERY APPLICATION.

THE MAGNETIC LOCK IS DESIGNED TO MOUNT TO THE DOOR FRAME ON THE STOP SIDE OF THE DOOR IN A

TYPICAL OUTSWINGING DOOR INSTALLATION,(SEE PAGE 2 FOR INSWINGING DOOR INSTALLATION).

SUFFICIENT HEADER SPACE MUST BE AVAILABLE TO MOUNT THE MAGNETIC LOCK TO INSURE A SAFE AND

SECURE INSTALLATION.

1. NOTE TYPE OF DOOR FRAME HEADER AND INSTALL FILLER PLATE OR ANGLE BRACKET AS REQUIRED TO

PROVIDE A FLAT MOUNTING SURFACE ON THE DOOR HEADER THE ENTIRE LENGTH OF THE MAGNETIC LOCK.

HEADER

HEADER HEADER

OUT

SWINGING

DOOR

OUT

SWINGING

DOOR

OUT

SWINGING

DOOR

MAGNET

FILLER

PLATE

MAGNET

ARMATURE

PLATE

ARMATURE

PLATE

ARMATURE

PLATE

ANGLE

BRACKET

HEADER

PLATE

2. FOLD TEMPLATE ON DOTTED LINE TO FORM A 90 DEGREE ANGLE. TAPE TEMPLATE AGAINST DOOR HEADER

WITH DOOR IN A CLOSED POSITION 1” FROM DOOR FRAME OPPOSITE HINGE SIDE OF DOOR JAMB.

FOR A PAIR OF DOUBLE DOORS PLACE TEMPLATE AT THE CENTER OF THE DOOR OPENING.

TRANSFER HOLE LOCATIONS TO DOOR AND FRAME HEADER, (SEE TEMPLATE INSTRUCTIONS).

3. FOLLOW TEMPLATE INSTRUCTIONS FOR HOLE SIZES. USE THE ILLUSTRATIONS BELOW TO DETERMINE THE

PROPER HOLE PREPARATION FOR THE ARMATURE PLATE ACCCORDING TO THE DOOR TYPE IN THE

INSTALLATION.

THE INCLUDED HARDWARE PACKAGE CONTAINS ALL NECESSARY ITEMS TO COMPLETE THE INSTALLATION.

HOLLOW DOOR

STEP 2

FOLLOW WITH

1/2” DIA. HOLE

THRU DOOR

STEP 1

DRILL 1/4” DIA.

HOLE THRU

ARMATURE

SIDE OF DOOR

STEP 2

DRILL 1/2” DIA.

HOLE THRU SEX

BOLT SIDE

OF DOOR

ONE THICKNESS

ONLY

STEP 1

DRILL 21/32” DIA.

HOLE THRU

ARMATURE

SIDE OF DOOR

ONE THICKNESS

ONLY

OUTSWINGING DOOR INSTALLATION

ARMATURE

PLATE MUST

ROCK ON DOOR

ARMATURE

PLATE MUST

ROCK ON DOOR

PLEASE READ BEFORE INSTALLATION

TO REMOVE THE HEADER PLATE INSERT HEX KEY INTO HOLES LOCATED AT

THE BOTTOM OF LOCK ON THE RIGHT AND LEFT SIDE AND UN-SCREW THE CAP SCREWS

Summary of content (6 pages)

PAGE 1
MAGNETIC LOCK INSTALLATION INSTRUCTIONS PLEASE READ BEFORE INSTALLATION ALARM CONTROLS CORPORATION OFFERS A COMPLETE LINE OF MAGNETIC LOCKS AND ACCESSORY ITEMS TO ASSIST THE INSTALLER IN MANAGING EVERY APPLICATION. THE MAGNETIC LOCK IS DESIGNED TO MOUNT TO THE DOOR FRAME ON THE STOP SIDE OF THE DOOR IN A TYPICAL OUTSWINGING DOOR INSTALLATION,(SEE PAGE 2 FOR INSWINGING DOOR INSTALLATION). SUFFICIENT HEADER SPACE MUST BE AVAILABLE TO MOUNT THE MAGNETIC LOCK TO INSURE A SAFE AND SECURE INSTALLATION. 1.
PAGE 2
INSWINGING DOOR INSTALLATION WITH L- Z BRACKET STEP 1 DOOR FRAME FASTEN THE L BRACKET ON THE DOOR FRAME IN A SUITABLE LOCATION. MOUNT THE MAGNETIC LOCK TO THE L BRACKET. MAKE SURE THAT THE MAGNETIC LOCK DOES NOT OBSTRUCT THE CLOSING OF THE DOOR. CONNECT THE CORRECT VOLTAGE TO THE MAGNET. L BRACKET ADJUSTABLE Z BRACKET STEP 2 ASSEMBLE THE Z BRACKET WITH THE SOCKET HEAD CAP SCREWS PROVIDED. DO NOT TIGHTEN THE CAP SCREWS AT THIS TIME. THE Z BRACKET MUST BE ADJUSTABLE.
PAGE 3
MAGNETIC LOCK L / Z BRACKETS FOR INSWINGING DOORS AM2370 FOR 300 POUND MAGNETIC LOCK AM3370 FOR ALL 600 POUND MODELS OF SINGLE MAGNETIC LOCKS AM6370 FOR ALL 1200 POUND MODELS OF SINGLE MAGNETIC LOCKS AM3375 FOR ALL 600 POUND MODELS OF DOUBLE MAGNETIC LOCKS AM6375 FOR ALL 1200 POUND MODELS OF DOUBLE MAGNETIC LOCKS MAGNETIC LOCK CARE AND MAINTENANCE MAGNETIC LOCKS HAVE NO INTERNAL MOVING PARTS AND REQUIRE A MINIMUM AMOUNT OF MAINTENANCE.
PAGE 4
WIRE GAUGE CHART DISTANCE FROM POWER SUPPLY TO MAGNETIC LOCK 12 VDC 50 FEET 100 FEET 150 FEET 200 FEET 300 FEET 400 FEET 500 FEET 750 FEET 1000 FEET 24 GA. 22 GA. 22 GA. 22 GA. 20 GA. 18 GA. 18 GA. 16 GA. 14 GA. 24 GA. 24 GA. 24 GA. 22 GA. 22 GA. 22 GA. 20 GA. 20 GA. 18 GA. 24 GA. 22 GA. 22 GA. 20 GA. 18 GA. 18 GA. 16 GA. 14 GA. 14 GA. 24 GA. 24 GA. 22 GA. 22 GA. 22 GA. 20 GA. 20 GA. 18 GA. 16 GA. 22 GA. 22 GA. 20 GA. 18 GA. 18 GA. 16 GA. 14 GA. 14 GA.
PAGE 5
MAGNETIC LOCK WIRING INSTRUCTIONS MODELS WITH BOND SENSOR AND DOOR STATUS SENSOR 600LB, 600DLB, 1200LB, 1200D To remove the header plate, it may be necessary to remove the wiring compartment screw. A long wiring compartment screw can be used to increase security by limiting access to the header plate mounting screw from below the lock.
PAGE 6
DESCRIPTION OF DOOR STATUS SWITCH BOND SENSOR AND LED DOOR STATUS SWITCH THE DOOR STATUS SWITCH IS AN INTERNAL REED SWITCH THAT OPENS WHEN THE DOOR IS OPEN AND CLOSES WHEN THE DOOR IS CLOSED. THE DOOR STATUS SWITCH CAN BE USED INSTEAD OF A SEPERATE MAGNETIC CONTACT ON THE DOOR. STATUS LED LED GREEN DOOR CLOSED AND MAGNETIC LOCK ENERGIZED. LED OFF NO POWER TO LOCK. LED RED DOOR OPEN AND MAGNETIC LOCK ENERGIZED. BOND SENSOR THE BOND SENSOR UTILIZES A HALL EFFECT SENSOR THAT DETECTS A MAGNETIC FIELD.