Quick Start Guide

ManualsBrandsAlarm.com ManualsElectronicsVideo Doorbell

ADC-VDB770 Quick Start Guide

In the Box

• ADC-VDB770 video doorbell

• ADC-VDB770 backplate with wire extenders

• Removal tool (for removing video doorbell from backplate after installation)

• Mounting brackets (3)

• Mounting wall screws (2)

• Mounting wall anchors (2)

• Mounting machine screws (2)

• Wire connectors (4)

• Power module (must be installed on all supported chime types)

Pre-Installation Checklist

• ADC-VDB770 and included accessories

• Wi-Fi connection to broadband (Cable, DSL, or Fiber Optic) internet

• A computer, tablet, or smartphone with Wi-Fi is required if the router does not have the

Wi-Fi Protected Setup (WPS) feature

1. Installation

1. Turn off electrical power to the doorbell transformer.

2. Install the Power Module and ADC-VDB770 according to the detailed instructions at

alarm.com/doorbell.

2. Connect

There are two options for connecting the device to the Wi-Fi network: Access Point (AP) mode

or Wi-Fi Protected Setup (WPS) mode.

Use WPS mode if you have easy access to the Wi-Fi router and the router has the WPS feature

enabled. Note that some Internet Service Providers disable the WPS feature on customer

routers. AP mode is the most reliable method for installing this device.

Summary of content (15 pages)

PAGE 1
ADC-VDB770 Quick Start Guide In the Box • • • • • • • • • ADC-VDB770 video doorbell ADC-VDB770 backplate with wire extenders Removal tool (for removing video doorbell from backplate after installation) Mounting brackets (3) Mounting wall screws (2) Mounting wall anchors (2) Mounting machine screws (2) Wire connectors (4) Power module (must be installed on all supported chime types) Pre-Installation Checklist • • • ADC-VDB770 and included accessories Wi-Fi connection to broadband (Cable, DSL, or Fiber Opt
PAGE 2
Connect the camera to the Wi-Fi network using AP mode or WPS mode: AP mode WPS mode 1. The camera’s LED will blink white after the boot up process. 1. After the boot up process is complete (the camera’s LED will be blinking white), hold down the doorbell button and release when the LED begins to blink blue (about 30 seconds). If the LED is not white after two minutes, hold down the doorbell button and release when the LED begins to blink white (about 45 seconds). 2.
PAGE 3
LED Reference Guide Status LED LED Status • Off •••• Blinking Red •••• Blinking Green • Solid Green Trouble Condition Power Cycle Factory Reset •••• Blinking Blue •••• Blinking White • Solid Red •••• Blinking Yellow •••• Alternating Red and Green Description Power off Power on, camera booting Local network connection Connected to Alarm.com WPS mode AP mode No local or Internet connection. See Troubleshooting section.
PAGE 4
Supplementary Info Alarm.
PAGE 5
Transformer Specification This device requires a minimum transformer voltage of 16V AC and a minimum transformer power of 10 VA.
PAGE 6
Find Chime Box Please make sure to turn off the electricity to your transformer before installing the power module. Locate your chime box.
PAGE 7
Install Power Module Loosen the screws on the chime associated with the transformer and doorbell. Set the wires aside. Take the power module and hook the curved white wires onto the screw terminals. Tighten the screws. Using a crimp tool and the connectors provided, connect the wires you set aside to the straight grey wires of the power module (either grey wire can be connected to either existing wire). Adhere the power module to the side of the chime. Replace the chime cover.
PAGE 8
Remove Existing Doorbell Remove the existing doorbell from the wall and disconnect the wires. Secure the wires so that they can be connected in a later step.
PAGE 9
Choose Mounting Bracket At the installation location, an angled mounting bracket can be used to modify the field of view. Choose a mounting bracket type best suited for your installation setup. Installation scenarios corresponding to mounting bracket types A, B, and C are provided below to guide your decision.
PAGE 10
Install Mounting Bracket Thread the existing wires through the mounting bracket. Install the mounting bracket to the wall using the included mounting screws.
PAGE 11
Thread Wire Extenders Thread the wire extenders through the backplate. Remove the wire caps.
PAGE 12
Crimp Wires Crimp the two wires coming through the backplate to the existing wires threaded through the mounting bracket.
PAGE 13
Mount Doorbell Backplate Install the doorbell backplate to the mounting bracket using the included machine screws.
PAGE 14
Verify LED Light Attach the doorbell to the backplate and turn the electricity back on. Check that the doorbell camera's light is flashing white after the boot process is complete. If the LED is solid red, press and hold the button until the light begins alternating green and red.
PAGE 15
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.