Alarm.
Pre-Installation Checklist • ADC-V723 camera (included) • AC Power adapter (included) • Wireless (2.4 or 5 GHz) connection to broadband (Cable, DSL, or Fiber Optic) Internet • A computer, tablet, or smartphone with Wi-Fi is required if the router does not have the Wi-Fi Protected Setup (WPS) feature • Login and Password for the Alarm.
WPS Mode Add the Camera to an Alarm.com Account To ensure sufficient Wi-Fi signal, complete these steps with the camera near its final location but prior to mounting. 1 Connect the camera’s AC power adapter and plug it into a nonswitched outlet. 2 Hold down the WPS button and release when the LED begins to flash blue (about 3 seconds). 3 Activate the WPS Mode on the router. The router will begin to connect to the wireless network. The LED will be solid green when the connection is complete.
AP Mode Add the Camera to an Alarm.com Account To ensure sufficient Wi-Fi signal, complete these steps with the camera near its final location but prior to mounting. 1 Connect the camera’s AC power adapter and plug it into a nonswitched outlet. 2 Hold down the WPS button and release when the LED begins to flash white (about 6 seconds).
LED Reference Guide Status Solid Green | Internet connection Local network and internet connection Flashing Green | Local network connection Local network connection only, no internet Solid Red | No network connection No local network or internet connection Flashing Red | System booting Camera is booting 4 ADC-V723 Installation Guide
Wireless Enrollment Flashing Blue | WPS Mode To enter WPS mode, push the WPS button and release when flashing blue (about 3 seconds). See instructions above to add the camera to your router and account using WPS. Flashing White | AP Mode To enter AP mode, push the WPS button and release when flashing white (about 6 seconds). See instructions above to add the camera to your router and account using AP mode.
Troubleshooting • If you have issues connecting the camera to the account, power cycle the camera and try again. • If issues persist, reset the camera to factory defaults by using the WPS button located on the back of the camera. Press and hold the WPS button until the LED is flashing Green and Red (about 15 seconds), then release the button. The camera will reboot with factory defaults. If the camera was previously installed to an Alarm.
Notes FCC Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Notes FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ISED This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference.
Notes Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur. No. Antenna Model Number Antenna Remark Type Gain(dBi) 5.1 2.4GHz 1 Dipole 3010001121L7 5.6 5GHz 3.5 2.4GHz 2 Dipole 3010001122L7 5.5 5GHz The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Notes The Country Code Selection feature is disabled for products marketed in the US/Canada. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.
© 2017 Alarm.com. All rights reserved.