User's Guide

ManualsBrandsAlarm.com ManualsElectronicswireless transceiver that operates in the amateur band, 902 Â– 928 MHz

Interlogix part number: 600-9400-IMAG

Alarm.com part number: ADC-IS-100-LP

Alarm.com Image Sensor

Copy

HARDWARE COMPATIBILITY

• Security Control Panel: Interlogix Simon XT v1.3 or higher or

XTi v 1.0 or higher

• Alarm.com Module: Simon XT Module with firmware 146 or

higher

module with firmware 151 or higher)

• Required Daughterboard: Image Sensor daughterboard (

attache

Alarm.com module)

• Available Zones: One zone per Image Sensor installe

d. On the Simon XT only, one

additional zone is required for the required daughterboard.

Up to three Image Sensors

may be added per system. (Note: The Alarm.com GSM Module

both Image Sensor and emPower™.)

HARDWARE INSTALLATION

1. Create Alarm.com Customer Account-

Select service plan (including Image Sensor

add-on) and register the Alarm.com module serial number on

the Dealer

2. Install Image Sensor Daughterboard-

Locate the connector on the back of the

daughterboard. Remove the green backing from the daughterboard mounting adhesive.

While the module is powered down, align the daughterboard

and module

Press to secure. (NOTE: Verify module compatibility before

attaching

daughterboard is difficult to remove and removing may damage hardware.

3. Install Alarm.com Module Inside Control Panel

4. FOR SIMON XT ONLY, Connect Daughterboard Alarm Wire-

On the XTi panel, the

blue alarm hardwire is not required and should not be connected.

to step 5. When using the Simon XT panel,

you must connect the

from the “HW” hardwire output located on the daughterboard

(use “HW” not “C”)

“HW2 IN” (terminal 3) slot on the Simon XT panel

to enable local alarm activations

Once an

Image Sensor has been enrolled into the panel, a hardwire zone will

automatically be programmed as “Sensor 39: ISHW.”

To ensure alarms are tripped

properly on Image Sensors according to their en

rolled group, the hardwire sensor group

is automatically configured.

Do NOT alter the sensor group of Sensor 39 ISHW

(Note: On the Simon XT, the panel scr

een will display “Sensor 39: IS

regardless of which Image Sensor tripped the alarm.

The Alarm.com

notifications,

and the central station report will indicate the specific Image Sensor that

tripped the alarm.)

5. Route Daughterboard Antenna-

It is important to be sure that daughterboard antenna

is pulled away from the Alarm.com module. Follow the panel-

specific antenna routing

guidelines to optimize sensor range.

Simon XT-

The antenna should be pulled down off the Alarm.com module

in a “J” shape to the left towards the corner of the panel

XTi v 1.0 or higher

higher

(XTi requires

attache

d to compatible

d. On the Simon XT only, one

Up to three Image Sensors

is required to use

Select service plan (including Image Sensor

the Dealer

Website.

Locate the connector on the back of the

daughterboard. Remove the green backing from the daughterboard mounting adhesive.

and module

connector.

attaching

. Once attached,

daughterboard is difficult to remove and removing may damage hardware.

)

On the XTi panel, the

For XTi panels, skip

you must connect the

included blue wire

(use “HW” not “C”)

to the

to enable local alarm activations

Image Sensor has been enrolled into the panel, a hardwire zone will

To ensure alarms are tripped

rolled group, the hardwire sensor group

Do NOT alter the sensor group of Sensor 39 ISHW

een will display “Sensor 39: IS

HW Alarm”

The Alarm.com

Website &

and the central station report will indicate the specific Image Sensor that

It is important to be sure that daughterboard antenna

specific antenna routing

The antenna should be pulled down off the Alarm.com module

an d routed

Simon XTi- Bend the antenna at a 90°

angle ¼ of an inch from the

daughterboard. The daughterboard

antenna

casing parallel to the panel.

the panel and initiate a

Alarm.com m

odule is properly installed and communicating with the Alarm.com

f the daughterboard LED is blinking, refer to

Daughterboard Status LED Activity Reference

LED Device Status or Error

Duration of LED Pattern

Z1 Solid

Red

Daughterboard is

Receiving Power

While the daughterboard is powered

the module is not in power save mode

Off

Daughterboard Not

Receiving Power or

Module in Power Save

Mode

Until daughterboard receiv

module returns from power save mode.

Z1 & Z2

Fast

Blinks

Incompatible Module or

Hardware Issue

odule not compatible w/ Image Sensor

(Firmware 146 &

hardware failure.

REGULATORY INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

resid

ential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that inte

rference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the

interferen

ce by one or more of the following measures: (1) Reorient or relocate the receiving antenna.

(2)

Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a

circuit different form that which the receiver is

connected. (4) Consult the dealer or an experienced radio/TV

technician for help.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, includin

g interference that may cause undesired operation.

This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a m

inimum distance of 20 centimeters between the radiator and

your body.

FCC ID: YL6-143IS20EVD IC: 9111A-143IS

Installation Guide

Rev 3.2

angle ¼ of an inch from the

edge of the

antenna

should rest inside the panel’s plastic

the panel and initiate a

comm-test to ensure the