User's Manual

ManualsBrandsAlarm.com ManualsElectronicsPart 15C Low Power Communication Device

- 1 -

Setup Instructions for GE

Simon XT with Alarm.com

GSM Module

These are the Installation Instructions for the

Alarm.com GSM Cellular Module for Simon XT. The

GSM Cellular Module enables wireless reporting of all

alarms and other system events from the GE

SimonXT control panel using an all-digital, GSM/GPRS

wireless (cellular) network. The module can be used

as the primary communication path for all alarm

signaling, or as a backup to a telephone line

connection to the central monitoring station. The

wireless alarm signaling and routing service is

operated by Alarm.com. The module interfaces with

the Simon XT panel board, fits into a special

compartment inside the panel, and is powered by the

control panel and panel battery.

Intended Use

Use this product only for the purpose it was designed

for; refer to the data sheet and user documentation.

FCC Compliance

Changes or modifications not expressly approved by

Alarm.com can void the user’s authority to operate

the equipment.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment

and receiver.

-Connect the equipment into an outlet on a circuit

different form that which the receiver is connected

-Consult the dealer or an experienced radio/TV

technician for help.

Installation

Installation consists of removing the plastic cover

over the antenna aperture, inserting the GSM

module inside the host, and attaching the antenna.

Follow these guidelines during installation:

• Do not exceed the hosts total output power when

using host power for the GSM module, hardwired

sensors, and /or sirens. Refer to the specific panel

installation instructions for details.

• Simon XT panels allow a maximum of one

Alarm.com GSM module.

• The GSM module draws a maximum of 30 mA

average during normal operation. In PowerSave

mode, during or immediately following an AC

power failure, the module will draw only 10 mA on

average.

• Avoid mounting the panel in areas with excessive

metal or electrical wiring, such as furnace or utility

rooms.

• Leave 12 to 18 in. of open space around the

module antenna.

• Do not install the control panel and module in a

basement or other below-ground location. Doing so

will negatively impact GSM signal strength.

Tools and supplies needed

You will need the following tools and supplies:

• Small flat-head and Phillips screwdrivers;

• Screws (included); and

• Antenna (included).

Troubleshooting: LEDs

Status LEDs indicate network and module status.

Figure 1 shows the location of the LEDs visible

through a slit at the back of the host.

Figure 1

Summary of content (4 pages)

PAGE 1
-Connect the equipment into an outlet on a circuit different form that which the receiver is connected -Consult the dealer or an experienced radio/TV technician for help. Setup Instructions for GE Simon XT with Alarm.com GSM Module These are the Installation Instructions for the Alarm.com GSM Cellular Module for Simon XT. The GSM Cellular Module enables wireless reporting of all alarms and other system events from the GE SimonXT control panel using an all-digital, GSM/GPRS wireless (cellular) network.
PAGE 2
Errors Flashed on LED 1 (RED) Table 1 describes the LED functions. LED L1 L2 L3 L4 Function Error LED. Will flash 1 to 8 times in an 8-second interval to indicate specific error conditions such as network error, host communication error, or GSM radio error. Host Communication. Flashes every time the Module communicates with the host. GSM Communication. Flashes every time the GSM signal level is checked or for every packet sent or received to and from Alarm.com. GSM Signal Level.
PAGE 3
• There is no GSM coverage in the area. Alarm.com recommends a signal level of 2 or higher for proper operation of the module. In connected mode, the LED toggles on and off. Improving wireless signal strength For optimal wireless signal strength, follow these guidelines: • Install the module above ground level, as high up as possible within the structure. • Install the module near or adjacent to an outside facing wall of the structure.
PAGE 4
5. Press the appropriate button(s) on the Z-Wave device to delete it from the network. For most devices, this involves just a quick press of the device button. 6. Observe the Busy light on the Alarm.com Z-Wave Snap device. The orange Busy light will become solid and stay solid for 1 minute once the device has been deleted successfully. (Once you’ve pressed the button on the device, it may take up to 5 seconds for the light to become solid.) 7. To delete another device, you can repeat the steps above.