IT82 Series Indoor Monitor User Manual 1
Content 1 Production Overview ................................................................. 4 1.1 Production Description ....................................................................................................... 4 1.2 Technical Specification ........................................................................................................ 6 1.3 Button Instruction ............................................................................................................... 6 1.
.3 Answer a call ..................................................................................................................... 28 3.4 Reject a call ....................................................................................................................... 29 3.5 Contacts............................................................................................................................. 29 3.5.1 New contacts ........................................................................
1 Production Overview 1.1 Production Description IT82 series is an Android SIP‐based with smooth touch‐screen Indoor monitor. It can be connected with Akuvox door phone for unlock and monitor. Residents can communicate with visitors via audio and video call, and support remote unlock the door. It is more convenient and safe for residents to check the visitor identity through its video preview function. IT82 series is often applicable in villas , apartments, building and so on.
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.
1.2 Technical Specification Model Graphic Display Network Protocol Voice Codec Video Codec Network Interface IP assignment Memory Management Dimension Storage IT82 series 7 inch capacitive touch screen TFT LCD, 1024x600 resolution, 16:9 wide screen aspect ratio SIP RFC3261,TCP/UDP/IP,RTP G.711A/U, G.729, G.722, iLBC_13_3, iLBC_15_2,OPUS H.264, H.263,H.
1.
1.
Interface Description 8 PIN connector For power supply and 485 connector 10PINconnect Ethernet 1 Ethernet 2 For 8 security connector Network interface can be connected to a hub, switch or other network access devices. Share the network access from ethernet 1 port, and for PC and other equipment connection. 1.
Use 4 ST4X20 screws Once the fixation to holes are made, fix the wall insert the four bracket in the wall expansion anchors provided Device Mounting Push down so that the device is fixed securely 1.7 Installation Considerations Here are some safety recommendations about the installation and the usage: Do not use this product near water, such as: bath, washbasin, kitchen sink and other damp places and so on. Place the device in a place away from heat.
1.
2 Setting 2.1 Main interface instruction It82 supports two pages of main interface. Click the corresponding area to operate. 2.2 Network 2.2.1 DHCP IT82 series use HCP mode to get IP address by default. Please go to Setting‐Advanced (password:123456)‐Network Choose DHCP,press CONFIRM, the phone will get IP address automatically.
2.2.2 Static IP Select Static IP in LAN Type. Enter the IP address parameters in the corresponding area.
Subnet Mask set the subnet mask of the device Gateway set the default gateway DNS 1 set the DNS address DNS 2 set the backup DNS address 2.3 Register Account SIP account is provided by SIP server. Go to Setting‐Advanced‐Sip Account . Please consult administrator about sip server information.
Fill the parameters in the corresponding area. Click CONFIRM to save. Parameter Specification Register Name SIP Account ID provided by ISP User Name SIP User Name provided by ISP Password SIP Password provided by ISP Display Name SIP Display name Reg Server IP SIP Register Server, format: domain/IP, for example: 194.168.1.2 Reg Server Port The default port is 5060. 2.4 Display 2.4.1 Brightness Slide the point left or right to adjust the screen brightness, click CONFIRM to save.
2.4.2 Sleep Choose the sleep time from 15 seconds to Never. IT82 series setup 1minute by default. After the sleep time without any operation, the phone will black screen. Touch it to wake up.
2.4.3 Screen Saver 2.4.4 Screen Clean This function is used to protect the device from being pressed any keys when users clean the screen.
2.5 Sound 2.5.1 Volume Slide the point right or left to adjust the Ring / Talk/Tone Volume. 2.5.2 Ring tones To setup the Phone Ringtone, click OK to confirm 2.5.3 Notification Sound Select the suitable notification sound, click OK to confirm. 2.6 Time Setup the date and time in the corresponding area. Enable Automatic Date Time , the phone will get the Date and Time automatically.
manually. Users can also select the suitable Time Zone and use 24‐Hour format. 2.7 System Info Enter System Info interface to check Account, Network and Version information.
To check the Network Access Mode And parameters. To check the Software version, Firmware version, Firmware Model and Hardware version. 2.8 Language Choose the suitable phone language. IT82 series use English by default.
2.10 Reset Go to Advance‐Reset. Choose the Reset mode,click CONFIRM when you see the prompt. The phone will reset to factory setting automatically. 2.11 Folder Click Folder to check the local and SD card files. IT82 series supports external SD card.
3 Function 3.1 Make a call User can directly dial from the soft keypad, select from the contact list or from call log to call out the number. User can choose one of the following steps to enter the dialing interface. Mode 1: Click Call icon on the main screen. Mode 2: Click Intercom button . 3.1.1 Call SIP If you want to call sip number, you can select Call SIP label. Click the sip number to make a call. The more information about sip account please consult administrator.
3.1.2 Call resident If you want to call room number, you can select Call Resident label. For example, if you want to call community 1, Building 1, Unit 1, Floor 1, Room1, you can input digits “001001010101”. 3.1.3 Call from Call Log User can enter the call log page to make a call. 1. In the dialing interface‐>click Intercom icon 2. Click Intercom button . Directly slide up and down to choose the number from the call history. Click Dail key to call out. 3.1.
Directly click Contact icon . If you want to make an audio call, click Audio Call icon video call, click Video Call . If you want to make a . Contact is shown as below: If the contact has multiple numbers, after clicking the calling mode, user need to choose the number you want to call.
3.1.5 Call Center If you want to call management center (SDMC system), you can press to call out. This function only can be used when IT82 series has registered from SDMC. 3.2 Receive a call Incoming calls include audio and video calls. If the caller has been stored in the contacts, it will show the contact name, otherwise the caller number will be displayed. When IT82 series received the video call, it can automatically get a screenshot and save it in the Album.
3.
that resident can view the visitors identity. Press Answer key to answer the call. As shown below: 3.4 Reject a call If user want to reject a call, click Cancel label in incoming interface. 3.5 Contacts 3.5.1 New contacts 1.Click Add button. 2.Enter the name. 3.Select the number type, and enter the parameters in the corresponding area. 4.Click CONFIRM to save.
3.5.2 Modify the contact 1. Choose the existed contact, click to edit. 2. Then modify the contact you need. 3. Click CONFIRM to save.
3.5.3 Delete the contact Choose the the existed contact you need to delete. Click to delete. 3.6 Call log Click Intercom, slide up and down to check the all call log in the marked box as shown below. 3.6.1 Modify the call log Choose one call log, click to modify the log. Users can create a new contact or send the message to this call log .
3.6.2 Delete the log Click in the corresponding log, choose Delete to remove the call log number. 3.7 Capture IT82 supports capture the visitor photo when incoming preview. IT82 series can auto capture if ringing for 3 seconds without answer. 3.8 Message Users can receive and write the message.
3.9 Live View Live view is used to monitor the door phone via using RTSP. 1.Path: Settings‐>More‐>Live View 2.Enter the door phone RTSP address.(please make sure the address format is right) 3.Click CONRIM to save. Then users can check the live video from the door phone any time. 3.10 Unlock IT82 series supports remote unlock the door phone via using DTMF code. During the call, users can press Open Lobby label or Unlock touch key to open the door during the call.
Note: IT82 series default DTMF code is #. Users need to predefine the same DTMF code of door phone and IT82. Configuration DTMF code, please consult your administrator. 3.11 SOS SOS key is used to call out the emergency number in case of emergency. IT82 series will call out for three predefined numbers in a loop, each number will be called for 60s (by default). 1. Go to Setting‐> More‐(password)>SOS 2. Set up 3 emergency number 3. Setup the call Timeout 4. Set up the loop time 5.
3.12 Security IT82 series support connect 8 alarm zones via IO1‐8 interface. Up to 5 Alarm Type ‐ Infrared, Drmagnet, Smoke,Gas and Urgency and two trigger mode ‐ NC(normal close) and NO(normal open) . Go to the path: Settings‐> More(Password:123456)‐> Arming Different alarm sensor is suitable for different type. For example , if you use the smoke detector in your bedroom(zoon1) , connect the sensor in IO1 and GND contact in IT82, then you can setup the type as Smoke.
Return to the main interface, click Arming. Setup alarm delay, the alarm will ringing after the alarm has been triggered. Open or close Alarm Status to enable or disable this function. Enter Zone Status to check 8 alarm zones working mode.
When the alarm is triggered, click Cancel and input “0000” to disable it.
4 Website 4.1 Web login The Akuvox IT82 series ses DHCP IP address by default, go to the path: Settings‐System Info‐Network to check the IP address. Open a Web Browser, enter the corresponding IP address. Then, type the default user name and password to log in.
4.2 Status 4.2.1Basic Sections Product Information Network Information Account Information Description To display the device’s information such as Model name, MAC address (IP device’s physical address), Firmware version and Hardware firmware.
4.3 Account 4.3.1 Basic Sections SIP Account SIP Server 1 Description To display and configure the specific Account settings. Status: To display register result. Display Label: Which is displayed on the phone’s LCD screen. Display Name: Which is sent to the other call party for displaying. Register Name: Allocated by SIP server provider, used for authentication. User Name: Allocated by your SIP server provide, used for authentication. Password: Used for authorization.
automatically within registration period. Sections SIP Server 2 Outbound Proxy Server Transport Type Description To display and configure Secondary SIP server settings. This is for redundancy, if registering to Primary SIP server fails,the IP phone will go to Secondary SIP server for registering. Note: Secondary SIP server is used for redundancy, it can be left blank if there is not redundancy SIP server in user’s environment. To display and configure Outbound Proxy server settings.
NAT TCP: Reliable but less‐efficient transport layer protocol. TLS: Secured and Reliable transport layer protocol. DNS‐SRV: A DNS RR for specifying the location of services. To display and configure NAT(Net Address Translator) settings. STUN: Short for Simple Traversal of UDP over NATS, a solution to solve NAT issues. Note: By default, NAT is disabled. 4.3.
Sections SIP Account Audio Codecs Video Codecs Subscribe Description To display current Account settings or to select which account to display. To display and configure available/unavailable codecs list. Codec means coder‐decoder which is used to transfer analog signal to digital signal or vice versa. Familiar codecs are PCMU(G711U), PCMA(G711A), G722 (wide‐bandth codecs), G729 and so on. To configure the video quality. Codec Name: The default video codec is H264.
Sections DTMF Call Description To display and configure DTMF settings. Type:Support Inband,Info, RFC2833 or their combination. How To Notify DTMF: Only available when DTMF Type is Info. DTMF Payload: To configure payload type for DTMF. Note: By default, DTMF type is RFC2833 which is the standard. Type Inband uses inband frequency to indicate DTMF tone which is most used to be compatible to traditional telephone server. Type Info uses SIP Info message to indicate DTMF message.
provisional messages, this means it will send ACK every time the IP phone receives a provisional SIP message from SIP server. User=phone: If enabled, IP phone will send user=phone within SIP message. PTime: Interval time between two consecutive RTP packets. Anonymous Call: If enabled, all outgoing call for the designated account will be anonymous number. Anonymous Call Rejection: If enabled, all incoming anonymous‐out call for the designated account will be rejected.
Sections Session Timer Encryption NAT Conference User Agent Description To display or configure session timer settings. Active: To enable or disable this feature, If enable, the ongoing call will be disconnected automatically once the session expired unless it’s been refreshed by UAC or UAS. Session Expire: Configure session expire time. Session Refresher: To configure who should be response for refreshing a session. Note: UAC means User Agent Client, here stands for IP phone.
4.4 Network 4.4.1 Basic Sections LAN Port Description To display and configure LAN Port settings. DHCP: If selected, IP phone will get IP address, Subnet Mask, Default Gateway and DNS server address from DHCP server automatically. Static IP: If selected, you have to set IP address, Subnet Mask, Default Gateway and DNS server manually. PPPoE: Use PPPoE username/password to connect to PPPoE server. 4.4.2 Advance Sections Local RTP Description To display and configure Local RTP settings.
stream can use. 4.5 Phone 4.5.1 Time/Language Sections Web Language NTP Description Choose the suitable web language you need. English by default. To configure NTP server related settings. Time Zone: To select local Time Zone for NTP server. Primary Server: To configure primary NTP server address. Secondary Server: To configure secondary NTP server address, it takes effect if primary NTP server is unreachable. Update interval: To configure interval between two consecutive NTP requests.
4.5.2 Call Feature Sections Mode Forward Transfer Description To enable or disable feature key sync. Feature Key Sync: To enable or disable feature key sync. Mode: Select the desired mode. To display and configure Forward setting. Note: There are three types of forward: Always Forward, Busy Forward and No answer Forward. Always Forward: Any incoming call will be forwarded in any situation.
DND phone is busy. No answer Forward: Any incoming call will be forwarded if it’s no answer after a specific time. DND (Do Not Disturb) allows IP phones to ignore any incoming calls. DND Emergency: the phone from the Authorized number can still be received after enable this function. DND Authorized Number: Setup authorized numbers for DND Emergency. Account: Select an account for DND DND: Disable by default.
Sections Intercom Remote Control Description Intercom allows user to establish a call directly with the callee. Active: To enable or disable Intercom feature. Intercom Mute: If enabled, once the call established, the callee will be muted. Remote Control allows specific host to interact with IP phone by sending HTTP or HTTPS requests. The specific action could be answering an incoming call, hangup an ongoing call and so on. Allowed Access IP List: To configure the allowed host address.
UACSTA Open Lobby Door Phone Others address list and IP address pattern as allowed hosts Using CSTA for SIP phone user agents. It can control some features of calling. UACSTA is used to send ECMA‐323(CSTA XML) information during SIP calling. The default status is disabled User can choose which types you need for each key. Akuvox IT82 supports 2 types to unlock‐DTMF and Relay. DTMF is used to unlock the lobby door remotly, Relay is used to open the local door.
4.5.3 Audio Sections Echo Canceller Description Echo Canceller: To remove acoustic echo from a voice communication in order to improve the voice quality . VAD(Voice Activity Detection): Allow IP phone to detect the presence or absence of human speech during a call. When detecting period of “silence”, VAD replaces that silence efficiently with special packets that indicate silence is occurring.
Automatical Control background sound is consistent throughout the call and the listener does not think the line has released. Generation R48G will auto adjust amplification circuit gain via signal. Automatic Gain Control(Sending‐side): Disabled by default Automatic Gain Control(Receiving‐side): Disabled by default Automatic Gain Control Target: Range from 1 to 20 dB. 3dB by default. NetEQ Filter forgetting factor base: Range from 0~255. 250 by default. 4.5.
sometimes called MPEG‐4 part 10. Others To setup corresponding H264 video parameters. H264 Profile: There are 4 modes‐Base、Main、High、 Extend profile. Different profiles makes different coding function and video quality. H264 Level: Different profiles has corresponding Level value. IDR Interval:IDR means Instantaneous Decoding Refresh. It is used to control the process of coding and decoding. Rate Control: Choose one H264 video rate.
4.6.2 Call Log Sections Call History Description To display call history records. Available call history types are All calls, Dialed calls, Received calls, Missed calls, Forwarded calls. HangUp: To click to hangup ongoing call on the IP phone. Note: For “HangUp” feature, you need to have the remote control privilege to control IP phone via Web UI. Please refer to section “Remote Control” in the Web UI‐>Phone‐>Call Feature page.
4.7.2 Advance Sections PNP Option DHCP Option Description To display and configure PNP setting for Auto Provisioning. PNP: Plug and Play, once PNP is enabled, the phone will send SIP subscription message to PNP server automatically to get Auto Provisioning server’s address. By default, this SIP message is sent to multicast address 224.0.1.75(PNP server address by standard). To display and configure custom DHCP option.
Sections Manual Auto Automatic AutoP Description To display and configure manual update server’s settings. URL: Auto provisioning server address. User name: Configure if server needs an username to access, otherwise left blank. Password: Configure if server needs a password to access, otherwise left blank. Common AES Key: Used for IP phone to decipher common Auto Provisioning configuration file.
Config file: To export or import configure file for IP phone. 4.8 Security 4.8.1 Basic Sections Web Password Modify Session Time Out Value Description To modify user’s password. Current Password: The current password you used. New Password: Input new password you intend to use. Confirm Password: Repeat the new password. Note: For now, IP phone can only support user admin. Over the session time out value, users need to login in the web again.
Sections Web Server Certificate Upload Client Certificate Client Certificate Upload Description To upload a certificate file which will be used as server certificate. To display or delete Certificates which is used when IP phone is connecting to any HTTPs server. To upload certificate files, this is used as client certificate. Only Accept trusted Certificates: If this option is enabled, only trusted certificates will be accepted.