VH9KDC500 KDC500 User Manual Rev 1.
KDC User Manual INTRODUCTION Table of Contents 1. INTRODUCTION ................................................................................ 7 1.1 Specification .............................................................................................................. 8 1.2 Package ..................................................................................................................... 9 1.3 Characteristics .............................................................................
KDC User Manual INTRODUCTION COPYRIGHT, LICENSE, and WARNING PAGE Copyright 2002-2015 by KOAMTAC, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from KOAMTAC, Inc. The material in this manual is subject to change without notice. KOAMTAC reserves the right to make changes to any product to improve reliability, function, or design.
KDC User Manual INTRODUCTION Regulatory Compliance US FCC ID: VH9KDC500A This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
KDC User Manual INTRODUCTION EMV Contact L1: 13248 0415 400 21 CEM EMV Contact L2: 2-03233-1-1C-TUU-0815-4.3.d, 2-03233-1-1OS-TUU-0815-4.3.d PCI PTS V4.0 5 Revision 1.0 Copyright®2012-2015, KOAMTAC, Inc.
KDC User Manual INTRODUCTION Battery Warning This device contains a rechargeable NiMH. Never throw the battery into a fire, as that could cause the battery to explode. Never short-circuit the battery by bringing the terminals in contact with another metal object. This could cause personal injury, a fire, and/or damage to the battery. Never dispose of used batteries with other ordinary solid wastes. Batteries contain toxic substances.
KDC User Manual INTRODUCTION 1. Introduction Bluetooth EMV/Chip&PIN/MSR/Barcode/NFC Mobile POS Companion The PCI compliant detachable EMV/MSR/Barcode/NFC SmartSled® design provides a secure and convenient user payment transaction and barcode scanning experience. Chipand-PIN payment solutions are becoming the global industry standard and as a result, KOAMTAC has developed the most advanced mobile payment companion.
KDC User Manual INTRODUCTION 1.1 Specification Main Processor 120MHz ARM Cortex-M4 Memory 1M program flash, 128KB RAM, 32-byte secure key storage, 8MB user data flash Display 128x64 monochrome Keypad Battery Secure Touch Pinpad(15 buttons) + 2 Scan buttons for barcode module .
KDC User Manual INTRODUCTION 1.2 Package The standard KDC500 package contains: 1. One KDC500 2. USB Cable 5pin Micro USB cable 3. KOAMTAC Installation CD with KDC Device Driver User Manual The following KDC accessories are available to purchase from www.koamtacstore.com or local reseller. Smartphone cases for KDC500 Charging cradles for KDC500 KDC500 SmartSled® adaptor KDC500 battery 9 Revision 1.0 Copyright®2012-2015, KOAMTAC, Inc.
KDC User Manual INTRODUCTION 1.3 Characteristics Before starting to use the KDC500, the user should become familiar with its physical characteristics. Refer to the follow figure that indicate the placement of 1D/2D Barcode Scanner, SCAN buttons, Secure Touch Pinpad, OLED display, LED, NFC Reader, Magnetic-Stripe Card Reader, IC Card Reader and ports on the KDC.
KDC User Manual INTRODUCTION 1.4 Scan Buttons Left SCAN Button Right SCAN Button Behavior ○ ○ ● ○ ○ ● Scan Barcode / Scroll up Scan Barcode / Scroll down Enter KDC500 menu Reboot KDC500 * ○(short press), -(no press), ● (long press, 5 sec) 1.5 Secure Touch Pinpad (Menu/Down button) While in the KDC500 menu, press this button to scroll down the selection bar. While on the main screen, press this button for 5 seconds then the KDC500 will enter the KDC500 menu mode.
KDC User Manual GENERATION APPLICATION 2. Installation 2.1 Bluetooth Pairing The KDC500 can read and store barcode data independently, but it can also be used in combination with a PC, PDA, smartphone, or tablet. To use the KDC500 to read barcodes while it is paired with another device, the user should first set up a pairing between the KDC and smart device via Bluetooth.
KDC User Manual GENERATION APPLICATION 3. Operating your KDC500 3.1 Getting Started Charge KDC500 Battery Prior to using the KDC500, the user should charge its battery by following the below instructions. 1. Connect the KDC500 cable to the micro USB connector on the KDC500. 2. Connect the KDC500 cable to the Type A USB connector on the computer. 3. The KDC500 battery will begin charging. Within a few minutes, the LED on the front panel will illuminate orange.
KDC User Manual GENERATION APPLICATION 2. Touch NFC tag to the NFC antenna symbol on the front case, and make sure the tag and case are within 4cm of each other. 3. The KDC500 will send the NFC tag UID to the paired host application and the user will hear a short beep if it has been read successfully. Read Magnetic-Stripe Card 1. The paired host application sends a command to enable the MS Card Reader. 2. Swipe MS Card either top to bottom or bottom to top.
KDC User Manual WARRANTY 4. Warranty LIMITED WARRANTY AND DISCLAIMERS BY OPENING THE PACKAGE OF THIS PRODUCT YOU AGREE TO BECOME BOUND BY THE LIABILITY AND WARRANTY CONDITIONS AS DESCRIBED BELOW. UNDER ALL CIRCUMSTANCES, THIS MANUAL SHOULD BE READ ATTENTIVELY, BEFORE INSTALLING AND OR USING THE PRODUCT. Serial Number A serial number appears on the KDC label. This official registration number is strictly related to the device purchased. Make sure that the serial number appearing on your KDC is not removed.
KDC User Manual BARCODES MULTIPLE SPECIAL 5. Contact Information CORPORATE HEADQUARTERS 116 Village Blvd., Suite 305 Princeton, NJ 08540, USA Phone: 609-256-4700, FAX: 609-228-4373 Email: support@koamtac.com For more information, visit our website - www.KOAMTAC.com 16 Revision 1.0 Copyright®2012-2015, KOAMTAC, Inc.
