Application Guide

ManualsBrandsAIRXCEL ManualsElectronicsThermostat

INSTALLATION, OPERATION &

APPLICATION GUIDE for

9630-3301

DIAGNOSTIC A/C-HP ZONE

CONTROL

FCC Warning

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two

conditions

(1) this device may not cause harmful

interference, and

(2) this device must accept any interference

received, including interference that may cause

undesired operation. Changes or modifications not

expressly approved by the party responsible

for compliance could void the user’s authority to

operate the equipment.

Note 1: This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment

and receiver.

—Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

—Consult the dealer or an experienced radio/TV

technician for help.

Any changes or modifications to this unit not

expressly approved by the part responsible for

compliance could void the user’s authority to

operate the equipment.

WARNING!

This appliance is not intended for use by young children or infirm persons unless they have been adequately

supervised by a responsible person to ensure they can use the appliance safely.

CAUTION!

This thermostat should be installed and programmed by trained technicians only. Adhere to all local and

national codes. Disconnect all power to the system before installing, removing, or cleaning.

APPLICATION

• Can control up to 4 ACs/HPs, 4 gas furnaces and 2 MAXXFans with one thermostat.

o MAXXFans must be diagnostic models that are equipped with the correct control board

o Rooftop units must be installed with the diagnostic control kit.

• Can operate as a single zone thermostat

• Constantly runs diagnostics and provides service codes when problems are detected

• Communication wire uses RJ45 connectors, OEM supplied.

• Bluetooth™ compatible.

Summary of content (6 pages)

PAGE 1
INSTALLATION, OPERATION & APPLICATION GUIDE for 9630-3301 DIAGNOSTIC A/C-HP ZONE CONTROL FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 2
INSTALLATION OEM supplies the RJ45 cable that connects the thermostat, control boxes and MAXXFans. MAXXFans require their own 12Vdc for 12Vdc fan functions. 12Vdc control voltage can be provided at either the control box or the thermostat and will be carried to the other components via the RJ45 cable. The thermostat comes with a mounting plate. Furnace wire is now at the control box. Thermostat and Room Temperature Sensor Location This system is designed to work one of two ways.
PAGE 3
according to which zone the board is to control. We recommend starting at the front of the coach as Zone 1 and progressing towards the rear. • If the board is to control Zone 1, then the Zone Assignment Switches should be set to 1) OFF & 2) OFF. • If the board is to control Zone 2, then the Zone Assignment Switches should be set to 1) On & 2) OFF. • If the board is to control Zone 3, then the Zone Assignment Switches should be set to 1) OFF & 2) ON.
PAGE 4
Note: If the system is in cooling and is programmed to have only a heating appliance connected in a zone, then the thermostat will still display the room temperature in that zone, but the user will not be able to operate any cooling appliance in that zone since there is not one connected in that zone. Your homeowner packet should contain literature that will list what heating and cooling appliances are installed in each zone of your motor home. Error Codes: No. Item 1 Room temperature sensor is bad.
PAGE 5
Functio n Mode Zone Dema nd Off N/A 1-4 N/A HP Mod e N/A Cool Cool Auto Cool Auto 1-4 No N/A 1-4 Yes N/A 1-4 No N/A 1-4 Yes N/A Compressor is energized; FAN HIGH is energized 1-4 No N/A FAN LOW is energized 1-4 Yes N/A Compressor is energized; FAN LOW is energized 1-4 N/A N/A FAN HIGH is energized (Setpoint cannot be adjusted) 1-4 N/A N/A FAN LOW is energized (Setpoint cannot be adjusted) Cool Cool High Cool High Cool Low Cool Low Fan High Fan Lower Off No units ope
PAGE 6
IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.