AirHarmony-1000 Installation Guide Part Number: UGD-D01006 System Release: 14.
© Copyright by Airspan Networks Inc., 2015. All rights reserved worldwide. Legal Notices The information contained within this document is proprietary and is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any specific agreements protecting Airspan Networks Inc. rights in the aforesaid information.
Table of Contents Document Information.............................................................................1 Abstract .................................................................................................................. 1 Revision History ..................................................................................................... 1 Warnings and Cautions...........................................................................2 Human Exposure to Radio Frequencies .............
AirHarmony-1000 Installation Guide Customer Care Help Desk ....................................................................12 Airspan Encourages Comments .......................................................................... 12 1 Introduction ....................................................................................... 13 1.1 AirHarmony-1000 .......................................................................................... 13 1.1.1 Deployment .....................................
AirHarmony-1000 Installation Guide 6.1 Connecting the AC/DC Power Converter to AirHarmony-1000 ..................... 39 6.1.1 Power Cable Preparation ............................................................................. 39 6.2 Wiring AC Power Cable on the AC/DC Converter ......................................... 41 6.3 Wiring AC Power Input Cable ........................................................................ 43 6.4 Fiber Ethernet (SFP) Cable Installation .................................
AirHarmony-1000 Installation Guide Figure 16: Back-2-Back Assembly ........................................................................................................ 30 Figure 17: Positioning wall mounting plate ........................................................................................... 31 Figure 18: Wall mounting plate fastened on wall .................................................................................. 31 Figure 19: Lift unit to top of mounting plate...................
AirHarmony-1000 Installation Guide Figure 56: cable trimmed ...................................................................................................................... 48 Figure 57: RJ45 plug assembly ............................................................................................................ 48 Figure 58: RJ45 crimping ...................................................................................................................... 49 Figure 59: Crimped cable ...............
AirHarmony Installation Guide Document Information Abstract This document details procedures for installing the Airspan’s AirHarmony 1000 Indoor-Pico Enterprise-Femto eNodeB variant. Revision History Revision Details Date Rev 0.1 October 2014 Initial document Reformatted and revised the document.
AirHarmony-1000 Installation Guide Warnings and Cautions Human Exposure to Radio Frequencies The AirHarmony-1000 antennas should be installed and operated from a minimum safe distance of: AirHarmony-1000 with Front Mount Antenna: 2.5m AirHarmony-1000 with External Antenna: 2.5m AirHarmony-1000 with Smart Beam Antenna (SBA): 0.
AirHarmony-1000 Installation Guide 3. This product is supplied with a grounding connection which must be connected. Do not defeat this important safety feature. 4. Static sensitive components inside - do not remove the lid or base: No user serviceable parts inside. 5. Position the power cord to avoid possible damage; do not overload wall outlets. 6. Do not place this product on or near a direct heat source, and avoid placing objects on the terminal. 7.
AirHarmony-1000 Installation Guide Service Information Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void the warranty. Disconnect the power to this product and return it for service if the following conditions apply: a. The terminal does not function after following the operating instructions outlined in this manual. b. Liquid has been spilled, a foreign object is inside, or the terminal has been exposed to rain. c.
AirHarmony-1000 Installation Guide DECLARATION OF CONFORMITY European Community, Switzerland, Norway, Iceland, and Liechtenstein Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Deutsch: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden Vorgaben der Richtlinie 1999/5/EU.
AirHarmony-1000 Installation Guide GPS Compliance The GPS is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
AirHarmony-1000 Installation Guide Maximum Output TX Power Table 1: AirHarmony-1000 FCC Maximum Output TX Power Frequency Band FCC TX EIRP 2300-2400 MHz TBDdBm TBDdBM 12dBi 2496-2 690MHz 39.86dBm 57.86dBm 18dBi Antenna Gain Table 2: AirHarmony-1000 ETSI Maximum Output TX Power Frequency Band ETSI TX EIRP 2300-2400 MHz 40dBm 52dBm 12dBi 2496-2 690MHz 40dBm 58dBm 18dBi Antenna Gain Caution: Do not set maximum output TX power to higher than local regulations.
AirHarmony-1000 Installation Guide Note: When using a front mounted antenna, external antennas cannot be used. Note: When using external antennas, the sun-shield must be used. Table 4: Front Mounted Sector Antenna Parameters Parameter Frequency Polarization Polarization discrimination Boresight gain Azimuth HPBW Elevation HPBW Electrical tilt Grounding 2.x GHz 2.3–2.7 Dual Slant ±45 18 dB 12 dBi 65 22 -1 DC GND 2.3–2.7 Dual Slant ±45 15 dB 7.5 dBi 90 ± 10 20 N/A DC GND 3.x GHz 3.3–3.
AirHarmony-1000 Installation Guide Figure 1: AirHarmony-1000 with front mounted antenna and AirHarmony-1000 with sun-shield UGD-D01006 Airspan Commercial and Internal Use 9
AirHarmony-1000 Installation Guide About This Document Purpose This guide provides the workflow and step-by-step procedures for Installing the AirHarmony-1000. These procedures include: Verify prerequisites Install wall / pole mount Install the AirHarmony-1000 Install the AC/DC converter Connect and manage cables Intended Audience This guide is intended for persons who are responsible for installing the AirHarmony-1000 equipment. These persons should have a working knowledge of the equipment.
AirHarmony-1000 Installation Guide Document Organization Chapter Contents Introduction Provides a comprehensive overview of AirHarmony 1000 and its installation. Getting Started Provides workflows for initial install and workflow. Verifying Prerequisites Lists the hardware, software, and client requirements for installation. AirHarmony-1000 Installation Describes how to install AirHarmony-1000.
AirHarmony-1000 Installation Guide Customer Care Help Desk Airspan’s Customer Care Help Desk offers prompt and efficient customer support services. Note: To avail Airspan’s Customer Care Help Desk support, you must be a registered user and must have a valid support contract. To register, click here and fill the Registration form. To create and update issue logs, send e-mails to Customer Care Help Desk.
AirHarmony-1000 Installation Guide 1 Introduction This section provides a descriptive overview of the Airspan’s AirHarmony-1000 Micro / Pico eNodeB variant and its place in the Airspan product suite. 1.1 AirHarmony-1000 AirHarmony-1000 is part of Airspan’s carrier-class 4G Micro eNodeB family. AirHarmony-1000 supports 3GPP’s Long Term Evolution (LTE) eNodeB specifications, providing high-speed data and mobility in order to meet the demands of the Broadband Wireless Access market.
AirHarmony-1000 Installation Guide Figure 2: AirHarmony-1000 assembled with Front Mount antenna and GPS Note: The illustration above displays the GPS connected directly to the top of the unit; there is also a remote GPS antenna option.
AirHarmony-1000 Installation Guide 2 Getting Started 2.1 Workflow of Installation The Workflow to install the AirHarmony-1000 is shown in the following diagram: Figure 3: Workflow Caution: Antennas must be connected and attached before AirHarmony-1000 is powered on.
AirHarmony-1000 Installation Guide 2.2 AirHarmony-1000 Installation Checklist Plan the installation of the AirHarmony-1000 by using the Installation Checklist, which you can find as a removable job aid in Appendix A for this guide.
AirHarmony-1000 Installation Guide 3 Verifying Prerequisites Prior to installing the AirHarmony-1000, verify the required safety, power, tools, parts and components. This chapter includes the hardware, software, and client requirements for installation. Important: Set up requirements for the installation is detailed in the Job Sheet, see Appendix A. 3.1 Verifying Site Requirements To set up the AirHarmony-1000, an IP connection to a Netspan server is required. 3.2 Verify Installation Requirements 3.2.
AirHarmony-1000 Installation Guide Installation Kit / Part Part No.
AirHarmony-1000 Installation Guide Installation Kit / Part Part No.
AirHarmony-1000 Installation Guide Table 10: AirHarmony-1000 Components Parts Images AirHarmony-1000 Unit (with front mounted antenna) in typical packing box HAR10-FM-U40-B01D AirHarmony-1000 Unit (with Sunshield) in typical packing box (Pending) HAR10-CN-U40-B01D Universal mounting plate HAR10-U-PMK-1 Pole Clamps X 2 (included in above) UGD-D01006 Airspan Commercial and Internal Use 20
AirHarmony-1000 Installation Guide Parts Images AC/DC Outdoor Power Converter Kit - HAR10-ACDCKIT-OD-1 Kit includes: PSU (shown) Mounting bracket + hardware Circular connectors (male & female) Serratub Maxi Clamp (2) GPS antenna - GPS-ANT-2 AC cable (3x18AWG) Outer Fiber Cables (ASX Optical cables in 8 available lengths) Ground cable with grounding lug (Note that the cable is ordered per meter and the lug is ordered separately.
AirHarmony-1000 Installation Guide AirHarmony-1000 is shown below from the Ethernet termination and RF port end views respectively. Copper Ethernet connection is currently unsupported. Figure 4: AirHarmony-1000 Unit, bottom termination Figure 5: AirHarmony-1000 Unit, Top, RF ports 3.2.5 Physical Dimensions AirHarmony-1000 is in an all outdoor enclosure. Table 11.
AirHarmony-1000 Installation Guide Variant Dimensions (H x W x D) Comment Front Mount Antenna 549 x 142 x 228 mm / 21.6 x 5.6 x 9.0 in. Future Deliveries 549 x 142 x 203 mm / 21.6 x 5.6 x 8.0 in. 770 x 142 x 203 mm / 30.3 x 5.6 x 8.0 in.
AirHarmony-1000 Installation Guide 4 Before Installation of AirHarmony-1000 Prior to installation of the AirHarmony either on a pole or a wall the GPS antenna should be connected and the all antenna connections should be weather-proofed. 4.1 Connection of GPS Antenna The following defines the connection of the GPS antenna which is installed directly to the top of the unit. 1. Remove the protective dust cap from the GPS antenna jack prior to mounting on the AirHarmony-1000. 2.
AirHarmony-1000 Installation Guide Figure 7: Verify connection of RF cable Caution: Do not over-tighten the RF connector. RF failures can result when the RF connector is over-tightened. Figure 8: Weather-proof the connection 2. Weather-proofing of the connections is mandatory. This is done with a layer of selfamalgamating tape followed by an over layer of PVC tape. Both the self-amalgamating tape and the PVC tape are available from Airspan. 3. Verify the RF connector is completely weather-proof.
AirHarmony-1000 Installation Guide 5 Installing AirHarmony-1000 Install the AirHarmony-1000 eNodeB by pole mount or wall mount. AirHarmony-1000 is mounted on a pole or wall with its pre-installed antenna (front mount or SBA variants (pending)) or in close proximity to its external antenna (connectorized variant). Take care to install the mounting plate the correct way up. This is with the slot openings in the bracket at the top edges as shown below.
AirHarmony-1000 Installation Guide Figure 10: Mounting plate on pole 3. Position mounting plate on the pole with slots facing up. 4. Feed clamp bands through the quick release locking mechanisms and wrap around pole. Figure 11: Assemble clamp bands (4 required) 5. Wrap the band to properly fit on the pole. Press down locking mechanism with band excess fed through the mechanism. Figure 12: Press down locking mechanism 6. Align and position each of the 4 pole clamps.
AirHarmony-1000 Installation Guide Figure 13: Tighten clamp bands 7. Mounting plate is installed and ready for AirHarmony-1000 mounting.
AirHarmony-1000 Installation Guide Figure 15: Mounted on pole 5.1.1 Installing AirHarmony-1000 Back-to-Back In the event you want to deploy two (2) AirHarmony-1000(s) on the same pole – back-to-back, then the installation must be performed so that the clamp bands used to secure the units to the pole do not interfere with the clamp bands of the other unit. Each unit is installed separately as explained above in Installing AirHarmony-1000.
AirHarmony-1000 Installation Guide Figure 16: Back-2-Back Assembly The difference in height between the installed units after installation will be 40mm. Note: The Universal Mounting plate for each AirHarmony-1000 must be mounted on the pole prior to assembling the AirHarmony-1000 units. Assemble each unit’s AC/DC Converter as explained in AC/DC Converter Pole Mount Assembly with the same deviation of the clamp bands. 5.2 Wall Mount Assembly The following images show the wall mount assembly. 1.
AirHarmony-1000 Installation Guide Figure 17: Positioning wall mounting plate 2. Mark the wall through the holes on the wall mount at the required height. 3. Attach the mounting plate to the wall using wall plugs (x4) rated for at least 8-10 Kg per fastener. Figure 18: Wall mounting plate fastened on wall Note: Wall plugs (x4) and necessary hardware are not supplied by Airspan and are the responsibility of the installer. Recommended minimum 8mm dia.
AirHarmony-1000 Installation Guide 5.3 Securing AirHarmony-1000 to the Mounting Plate Note: The following procedure shown with the Front-Mount antenna variant as shown below. To mount AirHarmony-1000 to the mounting plate, perform the following: 1. Loosely fit the flange nuts on the studs protruding from the sides of the unit. Figure 19: Lift unit to top of mounting plate 2. Hook the studs into the top slots of the mounting plate. Figure 20: unit engages into slots on the top of mounting plate 3.
AirHarmony-1000 Installation Guide Figure 21: AirHarmony-1000 unit engaged into the bottom slots 4. Tighten the flange nuts (4 places) to the required degree of down-tilt. 5. Check and tighten all flange nuts. 5.4 Front Mount Antenna Tilt Adjustment On the Front Mount Antenna variant it is possible, after assembly to adjust the front mounted antenna tilt-down. There are adjustment slots located on the sides of unit body and on the sides of the front mounted antenna mounting plate.
AirHarmony-1000 Installation Guide Figure 23: Tilt adjustment antenna 3. After adjusting to the required tilt amount tighten both flange nuts and both screws. The antenna has an electrical fixed down-tilt of 1°. 5.5 LED Display A single tri-color LED (Green/Red/Orange) appears at the bottom of the unit, providing unit status indication.
AirHarmony-1000 Installation Guide Note: Prior to insertion apply No-Ox or other approved anti-oxidation agent. This ground cable should be connected to a protection ground bar or clamped directly to a steel structure. A direct earth ground connection is required for the surge protection devices inside the AirHarmony-1000 to be effective. 1. Remove grounding screw and slip the ring terminal end of the ground cable onto the screw prior to re-setting into the threaded hole.
AirHarmony-1000 Installation Guide Note: When installing a protection ground take care to use suitable metal combinations to avoid or minimize galvanic corrosion. 5.7 Installing AC/DC Converter The AC/DC power converter kit can be optionally supplied by Airspan. The kit includes the following: AC/DC power converter with cables on both AC and DC side. The DC side comes preconnected to the AirHarmony-1000 DC plug and the AC side arrives with 3 bare wires.
AirHarmony-1000 Installation Guide Figure 28: Tighten clamp bands 6. Mounting bracket is installed and ready for AC/DC Converter mounting. 7. Align the 4 mounting slots located on the flange of the AC/DC Converter with the 4 threaded holes on the mounting bracket. 8. Insert the 4 pan head screws (supplied) and tighten. Figure 29: Pole mounting – exploded view 5.7.2 AC/DC Converter Wall Mount Assembly The following images show the wall mount assembly.
AirHarmony-1000 Installation Guide Figure 30: Wall mount – exploded view Figure 31: Wall mount Note: Wall plugs (x4) and necessary hardware are not supplied by Airspan and are the responsibility of the installer. Recommended minimum 8mm dia. with appropriate wall plugs according to field conditions.
AirHarmony-1000 Installation Guide 6 Cable Connections Hazardous voltage! Before working, ensure that the power is removed from the power connection cables. When the system is powered on, do not touch the power terminals. 6.1 Connecting the AC/DC Power Converter to AirHarmony-1000 The DC Connector comes pre-assembled on the AC/DC Converter, as shown below: Figure 32: AC/DC Converter with DC power connector 6.1.
AirHarmony-1000 Installation Guide Figure 34: Power connection - on bottom panel of AirHarmony-1000 4. Screw the gland connector plug securely into the body cavity of the unit using the provided Gland wrench. 5. Tighten the tail nut on to the body forcing the seal to compress around the power cable using the (provided) Gland wrench. Figure 35: Power cable assembly Caution: Do not over tighten the gland connector or the tail nut. The gland nut should be tightened to a torque of no more than 3.3 Nm (2.
AirHarmony-1000 Installation Guide 6.2 Wiring AC Power Cable on the AC/DC Converter Advice: It is good practice to label both ends of the cable to identify which AirHarmony1000 unit it is connected to. Advice: It is good practice to leave a spare loop of cable (approximately 0.5m). This will allow for easier wiring and will allow the cable to be re-terminated if necessary in the future. Note: This is a waterproof connection therefore the use of die-electric gels is not required.
AirHarmony-1000 Installation Guide 5. Secure the prepared ends of the power cable into the head part of the connector (male part with visible pins). Figure 41: Secure cable to connector 6. Insert and secure the brown wire into position 1 and the blue wire into position 2 and green wire into position (earth ground). Figure 42: Power cable wires assembled Note: Individual connection numbers are marked on each part of the connector. Note: Set screw maximum recommended tightening torque of 0,3 Nm.
AirHarmony-1000 Installation Guide Figure 44: Assemble and tighten 6.3 Wiring AC Power Input Cable 1. Cut the AC power cable to the required length. 2. Prepare the ends of the AC/DC converter cable and thread the connector parts over the cable. 3. Secure the prepared ends of the drop cable into the head part of the connector (female part). Figure 45: AC/DC converter cable connector assembly 4.
AirHarmony-1000 Installation Guide Figure 48: Connector assembled and tightened 6.4 Fiber Ethernet (SFP) Cable Installation The Fiber Ethernet Small form-factor pluggable transceiver (SFP) must be connected to the AirHarmony -1000 using an outdoor fiber cable. The optical connection enables a one-hand installation of the connector.
AirHarmony-1000 Installation Guide Figure 50: Cable connector hook up to the board connector 4. Verify that the locking latch on the cable connector is engaged on the board connector. 5. Slide the inner housing and ground shield (if present) over the cable and over the molding. Figure 51: Slide on inner housing Note: Check that there no space between the inner housing and mounting flange. Check and remove any debris that might interfere with the connection. 6.
AirHarmony-1000 Installation Guide Figure 52: Slide over and click Note: The shell should be hand tightened only. Do NOT use tools to tighten the shell. 7. Once the connector is properly installed, the cable should be positioned and secured to minimize stress on the cable and connector. 6.5 Copper Ethernet Cable Installation Note: The following images are for illustration purposes only. The actual tools or hardware may differ according to manufacturer.
AirHarmony-1000 Installation Guide 6.5.2 Tool Requirements Table 15: Tools Tool Wire Cutters/snips Recommended (or equivalent) Image (examples) Standard CAT5e Jacket Strippers RJ45 Crimping Tool Fluke Networks UTP/STP Adjustable Cable Stripper and Cutter – Model # - 11230002 Fluke Networks Modular Crimper RJ45 - Model # 11212530 Ethernet Cable Tester Standard 6.5.3 Assembly Instructions In order to properly assemble the Ethernet cable follow the steps listed below: 1.
AirHarmony-1000 Installation Guide Figure 54: Ethernet cable stripped 6. Untwist the pairs to within 1/8" of the jacket. Arrange the wires according to TIA/EIA 568B standards. Flatten and align the wires. Figure 55: RJ45 wire positioning 7. Make one straight cut across all the wires, with the wire snips. Figure 56: cable trimmed 8. Hold the connector in front of you with the locking tab down. Orient the wires so connector Pin 1 aligns with cable Pin 1, etc. 9.
AirHarmony-1000 Installation Guide 12. Insert cable/connector assembly into the crimping tool and crimp until all pins are set and the ratchet lever is released. Figure 58: RJ45 crimping Note: All pins should be fully compressed and of equal height after crimping. 13. Place the drain wire of the cable thru the metal shell of the shielded plug. 14. Crimp the drain wire to the metal shell of the shielded plug with the crimping tool. Figure 59: Crimped cable 15.
AirHarmony-1000 Installation Guide 7 Additional Installations (Non-Standard) 7.1 Front Antenna Assembly Note: The following section is included for spare-parts or replacement assembly instructions as front mounted antenna variants come factory pre-assembled. The AirHarmony-1000 unit can be used either with a sector antenna mounted directly on the front or with a remotely attached antenna. The following describes the installation procedure for the front mounted antenna.
AirHarmony-1000 Installation Guide For installation of a remotely mounted antenna follow the antenna manufacturer’s instructions and connect the antenna to the AirHarmony-1000 using the appropriate cables. (Weather-proofed N-type Heliax RF cables (ordered separately). 1. Attach, connect and secure the RF cable between the external antenna and the appropriate RF connection on the top of the unit. Figure 62: Connecting RF cable Caution: Do not over-tighten the RF connector.
AirHarmony-1000 Installation Guide A Job Sheet This job sheet enables the users to keep track of their installation. It covers all the prerequisites required for accomplishing the AirHarmony-1000 installation.
AirHarmony-1000 Installation Guide B Checklist During installation, review and perform all the steps on this checklist (in the given order). This checklist is meant for the person who performs the AirHarmony-1000 installation. It includes the high– level steps involved in the installation process. Tip: To make sure you complete all the tasks, detach or print this checklist and use it as a job aid. After performing, check off each task. Procedure Action Check If Performed Verify the site requirements.
AirHarmony-1000 Installation Guide C Abbreviations Term Expansion 3GPP 3rd Generation Partnership Project, responsible for LTE ABS Almost Blank Subframe ACS AWGN Adjacent Channel Selectivity is a measurement of a receiver's ability to process a desired signal while rejecting a strong signal in an adjacent frequency channel.
AirHarmony-1000 Installation Guide LED Light Emitting Diode LTE Long Term Evolution MAC Medium Access Controller – responsible for several functions such Error Correction, Packet (De)Multiplexing, etc… MBSFN Multicast-Broadcast Single Frequency Network is an LTE feature designed to deliver services such as Mobile TV using the LTE infrastructure, and is expected to be a competitor to DVB-H-based TV broadcast MCS Modulation and Coding Scheme MME Mobility Management Entity is the key control-node fo