AS4000 Wireless Local Loop System DA Central Terminal Commissioning Unit Operators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 Notice 1. This manual is subject to revision. 2. All rights reserved. 3. Right of modification reserved. 4. This manual is supplied without liability for errors or omissions. 5. No part of this manual may be reproduced or used except as authorised by contract or other written permission. 6.
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 Safety Instructions - Warnings and Cautions SAFETY 1. Read and follow all warning notices and instructions marked on the product or included in this manual 2. Do not allow anything to rest on the power cord and do not locate the product where persons could step or walk on the power cord. 3.
AS4000 DA CT Commissioning Unit Operators Manual Preface 605-0000-455 Issue 2.0 Date 21/03/00 NOTE Airspan products do not contain hazardous substances (as defined in UK ‘Control of Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances Regulations 1990’).
AS4000 DA CT Commissioning Unit Operators Manual IXL 001 605-0000-455 Issue 2.0 Date 21/03/00 INDEX TASK LIST PREFACE: Safety Instructions Warnings and Cautions Index Task List.................................................................................................... IXL-001 GENERAL SYSTEM INFORMATION: GSI Introduction.......................................................................................................... GSI-001 1. Purpose of Document...........................................
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual GSI 001 605-0000-455 Issue 2.0 Date 21/03/00 INTRODUCTION 1. Purpose of Document This document describes the operation of the Airspan AS4000 DA Central Terminal Commissioning Unit 2. Prerequisite skills This manual is intended for use by persons familiar with the Airspan product having attended the Airspan CT training course prior to performing the procedures in this practice.
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual GSI 002 605-0000-455 Issue 2.0 Date 21/03/00 DA COMMISSIONING UNIT 1. Introduction The DA Commissioning Unit (DACU) is used during system commissioning and routine maintenance. The Unit can be used to commission the AS4000DA Central Terminal. 2.
AS4000 DA CT Commissioning Unit Operators Manual GSI 002 605-0000-455 Issue 2.0. Date 21/03/00 TX/RX Shelves 1&2 TX/RX Shelves 3&4 RF Combiner Shelf Commissioning Unit DC Supply Power Meter PC with Sitespan and LAT terminal software Modem Shelf 1 Modem Shelf 3 Modem Shelf2 Modem Shelf 4 CT Rack Figure 1.
AS4000 DA CT Commissioning Unit Operators Manual GSI 002 605-0000-455 Issue 2.0. Date 21/03/00 5. DA Commissioning Unit 5.1. Mechanical The Commissioning Unit measures 600mm wide, 300mm deep. 100mm high and can be rack mounted if required.
AS4000 DA CT Commissioning Unit Operators Manual GSI 002 605-0000-455 Issue 2.0. Date 21/03/00 5.2. RF Interconnect The Commissioning Unit has two RF ports (SMA connectors 50 Ohm impedance) the RF lead is connected to port A and to the RF antenna port using one length of RF cable and one coupler per antenna port. Unused ports are terminated using 50 ohm RF loads. All couplers and cables are marked to show insertion loss. Antenna Feed J2 80 dB Coupler N type connector J1 J3 SMA connector DIP/LNA 5.3.
AS4000 DA CT Commissioning Unit Operators Manual GSI 002 605-0000-455 Issue 2.0. Date 21/03/00 5.4. Shelf Controller Communications Connect to the management system port of the modem shelf to the Commissioning Unit D-type labelled AGC/PC MON. A female 25 pin D type connection is presented on the adapter for connection to the LAT Terminal.
AS4000 DA CT Commissioning Unit Operators Manual GSI 002 605-0000-455 Issue 2.0. Date 21/03/00 5.6.
AS4000 DA CT Commissioning Unit Operators Manual DLP 001 605-0000-455 Issue 2.0 Date 21/03/00 CENTRAL TERMINAL COMMISSIONING USING THE DACU 1. Preparation for Commissioning at the Central Terminal To make it possible for the test DACU to acquire a link the RW Management and Net Entry has to be set via the AS8100 Sitespan as follows: 1. From the Object List Shelf view select the modem shelf, click right mouse button and select the ‘element view’ 2.
AS4000 DA CT Commissioning Unit Operators Manual DLP 001 605-0000-455 Issue 2.0 Date 21/03/00 4. In order to acquire a test radio link using an ST, Sitespan must be used to place RW codes ‘Out of Service’(OOS) for either 10k or 160k bandwidths. These can be selected from the DTU card properties. The options for each RW code are: • IS • OOS • OOS(10k) bandwidth. • OOS(160k) bandwidth. - The RW is in service - This takes the RW out of service.
AS4000 DA CT Commissioning Unit Operators Manual DLP 001 605-0000-455 Issue 2.0 Date 21/03/00 2. Power Cycle the Rack The rack should be power cycled. 3. Check DACU Calibration Each DACU is provided with a calibration table on the cover unit a typical table is shown below. The path loss is equal to the sum of the unit losses and external losses. Cable Loss dB 1 2 3 4 5 Coupler Loss 80 80 80 80 80 Unit loss 17 17 17 17 17 RX sensitivity -98 -99 -100 -101 -102 Power meter Reading -3.68 -2.68 -1.
AS4000 DA CT Commissioning Unit Operators Manual DLP 001 605-0000-455 Issue 2.0 Date 21/03/00 * The rate at which the link will acquire is defined as follows: 1: 10kbit/s 2 40kbit/s 3 80kbit/s 4: 160kbit/s 7. For testing type in the code relating to the system as set up i.e. LK 7 1 4 4 0 9. In the example above the DACU is forced to acquire on RW 7, PN 1, with Uplink and Downlink of 160kbit/s, using RF channel 9 within the RF band. With the LAT connected to the DACU, ensure that it has booted-up.
AS4000 DA CT Commissioning Unit Operators Manual DLP 001 605-0000-455 Issue 2.0 Date 21/03/00 15. When the Sitespan connects it configures the OOS and Net Entries but as a precaution it may be prudent to set all lists in the DTU properties to OOS. 16. Power off the DACU. 17. With the LAT connected to the DTU, restore the DTU from test mode by typing TE 1. 18. Disconnect the RF cables from the rack and connect the Antenna. The rack is now fully commissioned. 5. Restoring shelf connections 1.
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual ICL-001 605-0000-455 Issue 2.0 Date 21/03/00 ISSUE CONTROL LIST Title Title Page ICL-001 IXL-001 GSI-001 DLP-001 Issue 2.0 2.0 2.0 2.0 2.
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual Abbreviations 605-0000-455 Issue 2.
DA Central Terminal Commissioning UnitOperators Manual 605-0000-455 Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 User Response Issue 2.
AS4000 DA CT Commissioning Unit Operators Manual 605-0000-455 Issue 2.