Package Contents * AR-MA405 X 1 * Power Adapter X 1 LED Indicator «Ethernet Cable X 1 » Quick Installation Guide AVILA 7 NR Power Port Reset button LAN Port WAN/LAN Port
Connecting the Primary Node Mesh @. Use the Ethernet cable to connect a LAN port of your modem or the community Broadband network port to the WAN/LAN port of AR-M405, @. Use the power adapter included In the package to connect AR-M405 to the power socket. And its LED indicator lights solid blue. Wait for about 50 seconds. The system finishes the start up process and LED indicator blinks blue. @. Connect the Mesh to your wireless or wired device.
Quick Setup for the Primary Node Mesh 1. Launch your web browser, enter airphomesh.net on the address bar, and press enter. nine metamorphosis a 2. Enter the login user name and password (Both are “admin” by default) and click Login.
3. Select your Time Zone and then click Next. Quick Setup @Time Zone Setting WAN Connection Setting Wireless Setting Finish Please select your Time Zone. Time Zone hes Alphecca Eschatology Co, Lid 4. Select your WAN connection mode according to your actual situation and then click Next. There are three connection types: Dynamic IP, Static IP, Poe. Take Dynamic IP as an example here.
5. You can change the network name and set a password for the network. Then click Next, Ea Quick Setup Ben Time Song Setting WAN Conn action Setting Wireless Setting Finish You can change the wireless network name and password, § morose Network Name ans Password Airport Tedhwotogy Co, Led 6. Check your settings. And then click Save.
Een WA Dae ell Wee Sah Hl La If the Mesh is connected to the internet successfully, its LED indicator should turn solid blue. Connecting the Secondary Nodes to the Internet For users who have purchased Info S3 or Info 54, you can expand network coverage in a Mesh system to get the best performance. (Note: Info 53 and Info $4 are the suite series products of AIRPORT) a. Plug each secondary node into a socket. Place it in the wireless coverage of another node. The best distance is not more than 20 meters.
b. Observe the LED indicator of the secondary Mesh until it lights one of the following colors: Solid blue Good Solid magenta Poor Solid yellow Medium level Solid red Disconnected Connection quality list c. If the indicator light is not solid blue or solid yellow, relocate it according to the placement advice in step a. to get a better connection. Accessing the Internet Wireless devices: Connect your wireless devices to your WiFi network using the SAID and password you set.
LED Indicator Explanation Status Explanation The system is starting. Solid blue The primary node is connected to the internet. The secondary node is connected fo the WiFi network of the primary node well. Blinking blue The system is not connected to the internet for less than 2 slowly minutes. Blinking blue . . Lastly The system has been connected to the internet just now. ] The secondary node is connected to the WiFi network of the Solid yellow Solid magenta primary node at a medium level quality.
The primary node is not connected to the internet. The secondary node is not connected to the WiFi network of Solid red the primary node. The secondary node is connected to the WiFi network of the primary node very poorly. Solid cyan process of restoring the Mesh(s) to factory settings. Sc lid white process of removing the node network. FAQ 1: How can I remove a node from my WiFi network? Al: Long-Press the Reset (RST) button of the node Mesh for about 20 seconds. And the LED indicator lights solid white.
AZ: Please do the steps below. 1): Power on the new node Mesh. 2): Remove the node of this new one from its original networking system. (Please refer to the operation of Al for details.) 3): Go to the Device Addition page on the web UI page of the primary Mesh and click Sean button. 4): Click Add. | Device Addition Add Back £33: How to restore the network to factory settings? A3: With your nodes powered on, long-press the Reset (RST) button of your node for about 6 seconds by a needle.
FE FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Caution! Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
AIRPORT TECHNOLOGY CO. LTD Add: G Zone, 3/F, Building 1, Aisha High-Tech Park, No.3011, Shah Road West, Xii Street, Anshan District, Sheen, China Email: Web: www.airpho.com Sean for mots info Copyright & Trademarked AIRPORT is a registered trademark of AIRPORT TECHNOLOGY CO, LTD Other brands and product names mentioned herein are trademarks or registered trademarks of their respective holders.