AiRISTA Flow A1 Tag USER GUIDE Revision 1.0 Copyright © 2020 AiRISTA Flow, Inc. All rights reserved. airistaflow.
Contents General ............................................................................................. 3 Use Cases for the A1 Tag ...................................................................................................... 3 Physical Features.................................................................................................................... 4 Dimensions: ................................................................................................................
General This user guide relates to the economical AiRISTA Flow A1 small factor BLE only Tag. Use Cases for the A1 Tag The AiRISTA Flow A1 tag is a multipurpose BLE 4.2+ tag. The tag can be worn in a wristwatch type format or on a key tag/ pendant or it can be attached to an asset that need to be tracked. The tag has a single tactile push button on the center top of the tag. The tag has optional Temperature and humidity sensors or a three axis Accelerometer.
Physical Features Dimensions: 7 mm x 40 mm (0.25 x 1.5 in) Thickness and Dial size. Weight: 23 g (0.8 oz). Specifications Environment: Operating Temperature: -40 to 70° C (-40 to 158° F). Storage Temperature: 10 to 25° C (50 to 70° F). Typical Operating Range: Line of Site: 45 meters (150 feet) at 5 dBm. Obstructions: 22 meters (75 feet) at 5 dBm. Electrical Interface: Long lasting replaceable 3V CR2032 coin battery (Up to 5 years at 1.5 second update interval). Certifications: FCC: Part 15.
Pendant or Wristwatch strap Splash Proof enclosure 3V CR2032 coin battery Tactile Push Button Multi-Color LED MAC address Optional Temperature and humidity sensor And/or 3 axis Accelerometer. Copyright © 2020 AiRISTA Flow, Inc. All rights reserved. airistaflow.
A1 Tag Activation and De-Activation Press the button on the tag and the tag will activate. The tag will automatically de-activate after 15 minutes if it is not in motion. (Not moved) Press and hold the button for 5 seconds to force the tag to reset. This action will stop the tag process and the button needs to be pushed again to activate the tag. Copyright © 2020 AiRISTA Flow, Inc. All rights reserved. airistaflow.
Battery Replacement The A1 tag can be opened by prying the front and back of the clam shell enclosure away from each other. Do not insert any device in the square slot as that is where the sensitive humidity sensor is located. Once you have the 2 parts of the enclosure separated you will see the battery located in a slide holder on the back of the PCB. Slide the battery (CR2032) out of the battery holder and replace with a fresh battery in the same polarity as the one removed.
When placing the A1 Tag PCB back into the enclosure make sure you line up the 2 alignment pins inside the mold with the holes in the PCB. After the battery was replaced close the A1 Tag by lining up the enclosure clips and then pressing the 2 parts of the enclosure together. Copyright © 2020 AiRISTA Flow, Inc. All rights reserved. airistaflow.
A1 Tag Programming with nRF Connect The tag should preferably be programmed by the controller server as it has over the air capability (OTA). The tag can also be re-configured from the standard default settings with the nRF Connect application that can be run from any device that has Bluetooth technology and that has the application to support it. It is recommended that you contact your AiRISTA Flow representative for more information on this process.
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Contact AiRISTA Flow, Americas 913 Ridgebrook Rd. |Suite 110 |Sparks, MD 21152 Tel: 1-844-816-7127 info@airistaflow.com Copyright © 2020 AiRISTA Flow, Inc. All rights reserved. AiRISTA Flow, Finland Vaisalantie 6 | 02130 | Espoo Tel: +358-10-326-7600 info@airistaflow.com airistaflow.