2029 Becker Dr Lawrence, KS 66047 User Manual WAYV Air FCC Version (Draft) D00.02.
029 Becker Dr Lawrence, KS 66047 Revision History: Version Number Date Authors Notes D00.00.01 Sept 16, 2019 Muhua Luo D00.00.02 Sept 19, 2019 Hao Liu Modify, supplement hardware related content D00.01.01 Sept 26, 2019 Andrew Megaris Translation and Technical Revision D00.02.00 Mar 4, 2020 Zhenyu Hu Initial draft for Wayv Air hardware ES2.0 D00.02.01 Mar 17, 2020 Zhenyu Hu Add RS485 Hub in Section 6 D00.02.02 Mar 26, 2020 Zhenyu Hu Add and test WiFi ‘Station Mode’ D00.02.
2029 Becker Dr Lawrence, KS 66047 IMPORTANT NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B device (commercial or industrial use), pursuant to Part 15 of FCC rules.
2029 Becker Dr Lawrence, KS 66047 Firmware Version Information Firmware/Software The latest Version Radar Application Firmware V2.0.29 Radar Bootloader V2.0.10 GUI Tool on Windows machine V1.0.1.6 Note: ● The table only indicates the latest version of firmware/software for Wayv Air. For previous versions information, please contact Ainstein.
2029 Becker Dr Lawrence, KS 66047 1. Introduction Wayv Air is a short-range radar that detects people indoors. It operates at 60GHz frequency band, and its detection range is up to 6 m. The small size and light weight make it feasible to be installed/mounted on ceiling or wall. 2. Specification Specification Operating Frequency 60.3 ~ 63.6 GHz Swept Frequency 3.
2029 Becker Dr Lawrence, KS 66047 3. Software (GUI and API) 3.1 Software Path Requirement The path of software (GUI) should only contain numbers and letters. DO NOT contain other characters or symbols. 3.2 Software Files and Structure ● Vave.exe ● icon folder; It contains icon image files, GUI is not able to work/display if this folder is missing. 3.3 API We also provide API with source code for the end-users who would like to receive data from Wayv Air and do their own customized development.
2029 Becker Dr Lawrence, KS 66047 ○ Voltage input ■ 5V~15V for RS-485 version ■ Maximum 5V for USB version ○ ● Typ. 4W Four-pin at on the left-hand side is A Pin # Description P1 GND P2 ● RS-485 D● USB Data- P3 ● RS485 D+ ● USB Data+ P4 Power Note: 1. The default version of Wayv Air is RS-485. If you have the USB version, ‘RS-485’ represents ‘Serial Port Communication’ in the rest of the description in this document. 2.
2029 Becker Dr Lawrence, KS 66047 4.2 Device Status LED and Interface Description 1. Status LED ○ System Booting: Magenta blink ○ Firmware Flash: Blue blink ○ Firmware Booting: Blue ON ○ Normal Operation: No Target -- Green blink; Target detected -- Magenta blink 2. Reset Button Long press to restore factory settings ○ Wifi Name: Device serial # ○ Password: 12345678 ○ Serial Port Communication Baud Rate: 115200 ○ Serial Port Communication ID: 1 ○ Initial Configuration: Default 3.
2029 Becker Dr Lawrence, KS 66047 1. Power Wayv Air device on. Make WiFi connection between host PC and Wayv Air ○ Set IPV4 address of host PC as: 192.168.4.
2029 Becker Dr Lawrence, KS 66047 2. Make RS485 AP Mode connection to query/configure the ‘WiFi work mode’ and ‘Server address’ (For details of RS485 AP Mode connection, please refer to Section 6.1) 1) Wayv Air is in WiFi AP Mode by default, if the user never configured it to WiFi Station Mode. Skip all the rest of steps in 4 and jump to 5. 2) After making RS485 AP Mode connection, click ‘System Config’ icon; Click ‘Query’ button on the bottom to show current configuration information.
2029 Becker Dr Lawrence, KS 66047 3. Click ‘Connection config’ icon, select ‘WIFI’ in ‘Connection config’ panel, port number 8877, then click ‘OK’ button 4. Click ‘Connect’ icon. GUI will pop up a ’Save File’ window, select the path and type the name you prefer to save the data, click ‘Save’ button; Or you can click ‘Cancel’ to skip it.
2029 Becker Dr Lawrence, KS 66047 5. If your host PC has multiple network adapters, please select the one with IP address of 192.168.4.65, this is the WiFi Adapter on your host PC you have set in step 3 above. 6. After selecting the proper IP, Wayv Air will be able to connect to the host PC and display the object(s), like the following figure.
2029 Becker Dr Lawrence, KS 66047 When the host PC and Wayv Air device make connections successfully, information of Wayv Air will be displayed in blue message, including Device ID, Temperature, Target number, etc. ○ Loc: Device IP address ○ ID: Device identification number ○ Firmware: Firmware version ○ SBL: Bootloader version ○ Target num: Current detected target(s) ○ TX1, TX2, TX3, PM: Device temperature 5.
2029 Becker Dr Lawrence, KS 66047 1. Set IPV4 address “Obtain an IP address automatically” 2. Find your host PC WLAN IP address. a. Windows OS: “ipconfig” in cmd b. Linux OS: “ifconfig -a” in terminal 3.
2029 Becker Dr Lawrence, KS 66047 4. Set ‘WiFi insert name’ and ‘WiFi insert code’ as exactly the same as name and password of current local network. 5. Set ‘Server address’ as the host PC’s WLAN IP address (IPv4). 6. Set ‘WiFi work mode’ as ‘Station mode’. 7. Click the ‘Config’ button on the bottom to complete this configuration, then reconnect WiFi. 8. After WiFi cascading configured and connected successfully (Station Mode), the GUI will show the same Result/Widget as AP Mode, that is track of objects.
2029 Becker Dr Lawrence, KS 66047 6. RS485 Mode Connection 6.1 RS485 Connection for Single Device (AP Mode) In RS485 AP mode, the hardware connection is shown as below, the ‘Converter Module’ is RS485-to-USB, we recommend to use Yu Tai UT-890A. 1. Hardware connect Wayv Air and host PC via Yu Tai UT-890A 2.
2029 Becker Dr Lawrence, KS 66047 2. Click ‘Connect’ icon, GUI will pop up a ’Save File’ window, select the path and type the name you prefer to save the data, click ‘Save’ button; Or you can click ‘Cancel’ to skip it. 3. Right click ‘485 BUS’, select ‘Detect’. GUI will automatically connect all units on RS485 bus. 4. Device number highlighted in Green is the active unit(s), highlighted in Red is the inactive unit(s). Uncheck all inactive unit(s).
2029 Becker Dr Lawrence, KS 66047 6.2 RS485 Cascading Connection (Station Mode) In RS485 Station mode, all Wayv Air units should be powered by an external 12V power supply. We recommend to use ‘RVV2*1.5’ cable for both power supply and RS485 communications. For details of this connection, refer to the Section 7 (RS485 Hub). 7. RS485 Hub Note: RS485 Hub is not included in Wayv Air; It is a separate accessory for users who require RS485 cascading connection. For details, please contact Ainstein.
2029 Becker Dr Lawrence, KS 66047 RS485 link. 100m to make sure data transmission robustness for The interface between RS485 hub and DSC (Data Service Center) is Ethernet cable or USB cable. 7.
29 Becker Dr Lawrence, KS 66047 7.2 RS485 Hub Setup and Connection RS485 Hub will be only used for users who need RS485 Station Mode connection, we prepare a separate document to describe the details of RS485 Hub setup and connection. Please contact Ainstein for this document if you require it. 8. CFG Setting In the GUI tool, there is a CFG module that can support dynamic configuration of Wayv Air. Here are some brief steps to do so. 1. Click ‘System config’ icon 2.
2029 Becker Dr Lawrence, KS 66047 2. Select the proper vave-firmware-version.bin file, then click ‘Open’. The update process will begin. Note: NOT vave-sbl.bin file. 3. When the process bar achieves 100% and shows ‘Success’, click the ‘Quit’ button to quit and complete the firmware update process. The Wayv Air should automatically reboot with the new firmware.
2029 Becker Dr Lawrence, KS 66047 10. Parameter Query and Change The GUI tool supports parameter query and change for Wayv Air. 1. Click ‘System config’ icon, check corresponding boxes and click ‘Query’ on the bottom, then it will shows current parameter 2.
2029 Becker Dr Lawrence, KS 66047 ● System work mode: There are three modes -- Normal mode, Points cloud mode, Production line mode ○ ○ ○ Normal mode: Display track of targets Points cloud mode: User need to set baud rate to 921600, GUI will display target’s point and cloud in three-dimension space (See Section 11 for more details) Production line mode: This mode for internal test purposes ONLY. No access to the end-users. 11.
2029 Becker Dr Lawrence, KS 66047 b. If the connection works on ‘921600’ in ‘Connection config’, go to step 2 in the following.
2029 Becker Dr Lawrence, KS 66047 Note: If the RS485 connection doesn’t work in either 115200 b/s or 921600 b/s, try to press and hold the ‘Reset’ button, then use 115200 b/s in ‘Connection Config’. 2. Once RS485 connection is successful, click ‘System config’ the current parameters. a. Change the ‘Points cloud’ in ‘System work mode’ b. Click ‘Config’ button to complete the configuration icon, then click ‘Query’ to see 3. In main window, click to open the point and cloud display window.
2029 Becker Dr Lawrence, KS 66047 Note: ONLY Wayv Air hardware with high-speed RS485 interface hardware can support point and cloud display. Please specify ‘Require high-speed RS485 interface’ when ordering or contact us before shipment. 12. Reset Wayv Air provides two methods to reset the device: 1. In GUI, type ‘restoreConf’ in CFG (See details of CFG in Section 8). After device rebooting, confirm all WiFi parameters are reset to the default values. 2.
2029 Becker Dr Lawrence, KS 66047 13. Disconnect Wayv Air Click to disconnect Wayv Air in the GUI.
2029 Becker Dr Lawrence, KS 66047 Contact Us: ADDRESS: 2029 Becker Drive, Lawrence, KS 66047 USA EMAIL: Hi@ainstein.
