Micro T-1™ User manual
1 PRESENTATION Aimpoint® red dot sights are designed for the ”two eyes open” method which greatly enhances situational awareness and target acquisition. Thanks to the optical design the red dot follows the movement of the user’s eye while remaining fixed on target, eliminating any need for centering. 1.
Signature No forward optical signature from the dot beyond 10 meters Power source Battery type One CR2032 Lithium battery Battery life3 More than 5 years of use at setting 8, more than 10 years at NVD-setting (1-4). Size (L × W × H) Sight 61 mm × 41 mm × 36 mm 2.4 in × 1.6 in × 1.4 in Configuration 61 mm × 41 mm × 46 mm 2.4 in × 1.6 in × 1.8 in Weight Sight (incl. battery) 86 g / 3.0 oz Configuration 114 g / 4.0 oz Height of optical axis Configuration (no spacer) 18 mm / 0.
Materials Sight and mount High strength aluminum, hard anodized, black to dark gray, non-glare finish Lens covers Rubber, black, non-glare finish Environmental specification Temperature range (operation) -45 °C to +71 °C -49 °F to +160 °F Temperature range (storage) -51 °C to +71 °C -60 °F to +160 °F Water resistance 25 m / 80 ft.
1.2 Overview (configuration) 1 2 6 9 A 3 11 5 B 4 7 10 C 12 8 Fig.
2 OPERATION WARNING: Ensure the weapon is not loaded and the safety selector is in the ”safe” position before attempting to install, remove or perform maintenance. NOTE: To reach maximum protection for all weather conditions, wax is added into the rubber mixture for the bikini lens covers. For long time storage, the wax can be seen as a grey film on the surface of the part. To restore to its original condition, please hand wash in warm dishwater. 2.
2.2 Install Aimpoint® Micro T-1 on a weapon If the sight is equipped with the mount shown in Fig. 1, follow the described procedure. For installation with other mounts, see accompanying instruction. a Loosen the screw (12) using the tool (10 C), and clamp the locking bar (11) around the Picatinny rail.
2 1 3 Fig. 2 Remove adjustment caps 1 Adjustment cap (2 pcs) 2 Elevation adjustment screw 3 Windage adjustment screw d Use any adjustment cap (1) or the tool (10 A) to turn the adjustment screws (2) and (3). Place the knobs on the adjustment cap (1) into the recesses on the adjustment screws (2) and (3). e Windage adjustments (see Fig. 3): • Turn windage adjustment screw (3) counterclockwise to move point of impact to the right.
NOTE: Each click of the adjustment screws corresponds to a 13 mm movement of the point of impact at 100 m or 0.5 in at 100 yds. Fig. 3 Windage adjustments Fig. 4 Elevation adjustments g Confirm zeroing by firing at least three shots at a zeroing target. Check points of impact to confirm accuracy and repeat zeroing procedure if required. h After initial firing, ensure the sight is securely installed on the weapon. 3 EXTREME CONDITIONS • Extreme heat (moist or dry): no special procedures required.
and by the use of the tool (10 B). Keep lens covers (9) on when the sight is not being used. Clean lenses and wipe the sight dry after exposure. • Dust storms and sand storms: keep lens covers (9) on when the sight is not being used. • High altitudes: no special procedures required. CAUTION: Never clean the lenses with fingers. Use lens paper/cloth. If lens paper/cloth is not available: • To clear away debris (sand, grass etc.): blow away the dirt or rinse with clear water.
The sight is impossible to zero If an adjustment screw is at its limit, check the alignment of mount and barrel. If point of impact is moving, check the stability of mount and weapon rail (or carry handle) The front lens of the sight is tilted, has the sight been damaged? No. The optical system is designed for the front lens to be mounted in this way.
Aimpoint AB Jägershillgatan 15 SE- 213 75 Malmö, Sweden Phone: +46 (0)40 671 50 20 Fax: +46 (0)40 21 92 38 e-mail: info@aimpoint.se Aimpoint Inc. 7309 Gateway Court Manassas, VA 20109, USA Phone: +1 703-263-9795 Fax: +1 703-263-9463 e-mail: info@aimpoint.com WWW.AIMPOINT.COM © 2008, 2017 Aimpoint AB.
