AGM Racer DM30-4MP Digital Monocular
Digital Rifle Scope / Clip-On User Manual Legal Information Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
Digital Rifle Scope / Clip-On User Manual CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Digital Rifle Scope / Clip-On User Manual EU Conformity Statement his product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Directive 2014/30/EU (EMCD), Directive 2014/35/EU (LVD), Directive 2011/65/EU (RoHS). Directive 2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Digital Rifle Scope / Clip-On User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Danger Indicates a hazardous situation which, if not avoided, will or could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.
Digital Rifle Scope / Clip-On User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. Laws and Regulations ● Use of the product must be in strict compliance with the local electrical safety regulations. Transportation ● Keep the device in original or similar packaging while transporting it. ● Keep all wrappers after unpacking them for future use.
Digital Rifle Scope / Clip-On User Manual ● ● ● ● ● DO NOT swallow the battery to avoid chemical burns. DO NOT place the battery in the reach of children. The battery cannot be charged with external power source directly. The device cannot be charged, please use the supplied charger to charge the battery. Please purchase the adapter by yourself. The using environment of the adapter should be consistent with that of the device.
Digital Rifle Scope / Clip-On User Manual COMPLIANCE NOTICE: The thermal series products might be subject to export controls in various countries or regions, including without limitation, the United States, European Union, United Kingdom and/or other member countries of the Wassenaar Arrangement.
Digital Monocular User Manual Table of Contents Chapter 1 Overview.................................................................................................................... 1 1.1 Device Description................................................................................................................. 1 1.2 Main Function ........................................................................................................................ 1 1.3 Function ..................................
Digital Monocular User Manual Chapter 6 Client Software Connection ...................................................................................... 13 Chapter 7 Language Settings..................................................................................................... 14 Chapter 8 Unit Settings............................................................................................................. 15 Chapter 9 Maintenance .................................................................
Digital Monocular User Manual Chapter 1 Overview 1.1 Device Description The digital night vision scope can perform in all ambient light. It has an advanced HD sensor and a high resolution OLED display, which provides full-color clarity in daytime and classic black & white viewing at night. The traditional-style tube meets the needs of professional hunters who value traditions and seek technological superiority. 1.
Digital Monocular User Manual No. Description Function 6 Fixing Ring Fix the eyepiece. 7 Diopter Adjustment Ring Adjust the dioptric correction. 8 Eyepiece View the target. 9 Data Exchange Interface Connect the device to power supply or transmit data with a type-C cable. 10 Laser Range Finder Measure the distance with laser. 11 Battery Compartment Install the battery in it. 4+5 Measure Key + Wheel Press to capture snapshots.
Digital Monocular User Manual Chapter 2 Preparation 2.1 Cable Connection Connect the device and power adaptor with a type-C cable to power on the device. Alternatively, connect the device and PC to export files. Steps 1. Lift the cable interface cover. 2. Connect the device and power adapter with a Type-C cable to power on the device. Alternatively, connect the device and PC to export files. 2.2 Install Battery Insert the batteries into the battery compartment. Steps 1.
Digital Monocular User Manual 2.4 Power On/Off Power On When the battery is sufficiently charged, hold Power Off When the device is turned on, hold for about 2 seconds to power on the device. for 2 seconds to power off the device. Auto Power Off Set the auto power off time for your device, and then the device will automatically shut down as the set time. Steps 1. Hold the wheel to go to the menu. 2. Rotate the wheel to select , and press the wheel to select the auto power off time as required. 3.
Digital Monocular User Manual Chapter 3 Image Settings 3.1 Adjust Diopter Steps 1. Power on the device. 2. Open the lens cover. 3. Hold the device and make sure the eyepiece covers your eye. 4. Rotate the adjust ring until the OSD text or image is clear. Note When adjusting diopter, DO NOT touch the surface of lens to avoid smearing the lens. 3.2 Adjust Focus Steps 1. Power on the device. 2. Hold the device and make sure the eyepiece covers your eye. 3. Adjust the focus ring until the image is clear.
Digital Monocular User Manual 3.5 Set Smart IR Image overexposure may occur in too bright environment. The smart IR function helps to adjust the overexposed images, and it can improve the image effect in night mode by adjusting the brightness of the supplement light. In menu mode, rotate the wheel to select and press the wheel to enable this function. 3.6 Set Display Mode You can select different display modes in different scenes. Hold in live view interface to switch display modes.
Digital Monocular User Manual Figure 3-3 PIP Effect 4. Hold the wheel to exit. Note ● When reticle is enabled, the PIP view is the detail of reticle. When reticle is not enabled, the PIP view is the detail of central part. ● If digital zoom is enabled, the PIP view also zooms. If the digital zoom ratio exceeds 4, the PIP does not zoom. 3.9 Set OSD You can choose whether to display the OSD information on the live view interface in this function. Steps 1. Hold the wheel to show the menu. 2.
Digital Monocular User Manual 5. Hold the wheel to save settings and exit. 3.10 Set Brand Logo You can add brand logo on the live view interface. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select . 3. Press the wheel to enable Brand Logo. 4. Hold the wheel to save the settings and exit. Result The brand logo is displayed at the right bottom of the image and video.
Digital Monocular User Manual Chapter 4 Measure Distance The device can detect the distance between the target and the observation position. Before You Start When measuring the distance, keep the hand and the position steady. Otherwise, the accuracy may be affected. Steps 1. Hold the wheel to show the menu. 2. Select and press the wheel to go to the setting interface. 1) Rotate the wheel to select the target from Deer, Grey Wolf, Brown Bear, and Custom.
Digital Monocular User Manual Chapter 5 Picture and Video You can manually record video or capture picture when displaying live view. 5.1 Capture Picture In the main live view interface, press and wheel at the same time to capture images. Note When capturing succeeds, the image freezes for 1 second and a prompt shows on the display. For exporting captured pictures, refer to Export Files. 5.2 Set Audio If you enable the audio function, the sound will be recorded with the video.
Digital Monocular User Manual Figure 6-1 Start Recording The left top of image displays the information of recording time. 2. Press the wheel again to stop recording. What to do next For exporting recording files, refer to Export Files. 5.4 Prerecord Video After you enable this function and select the prerecording time, the device can automatically start recording the 7, 10 or 15 seconds before the recoil-activation and end recording the 7, 10 or 15 seconds after the recoil-activation. Steps 1.
Digital Monocular User Manual Before You Start ● Turn off the hotspot function. ● Turn on the device after connecting it to your PC, and keep the device on for 10 to 15 seconds before other operations. Steps 1. Connect the device and PC with a Type-C cable. Note Make sure the device is turned on when connecting the cable. 2. Open computer disk and select the disk of device. Go to the DCIM folder and find the folder named after the capture year and month.
Digital Monocular User Manual Chapter 6 Client Software Connection Connect the device to the T-Vision App via hotspot, then you can capture picture, record video, or configure parameters on your phone. Steps 1. Hold to show the menu of device. 2. Press to enable hotspot function. 3. Turn on the WLAN of your phone and connect to the hotspot. ● Hotspot Name: Wlan-IPTS Serial No. ● Hotspot Password: the last 9 digits of serial No. 4.
Digital Monocular User Manual Chapter 7 Language Settings You can select the device language in this function. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to enter the language configuration interface. 3. Rotate the wheel to select the language as required, and press the wheel to confirm.
Digital Monocular User Manual Chapter 8 Unit Settings You can switch the unit for the distance measurement function and the reticle function. Steps 1. Hold the wheel to show the menu. 2. Rotate the wheel to select , and press the wheel to switch the unit. Yard and m are selectable. 3. Hold the wheel to save settings and exit.
Digital Monocular User Manual Chapter 9 Maintenance This part introduces the operation of checking device information, upgrading device, and restoring to defaults, etc. 9.1 View Device Information Steps 1. Hold the wheel to show the menu of device. 2. Select , and press the wheel. You can view the device information such as version, and serial No. 9.2 Upgrade Device Before You Start ● Please get the upgrade package (including Main Firmware and FPGA Firmware) first.
Digital Monocular User Manual Chapter 10 Frequently Asked Questions 10.1 Why is the monitor off? Check whether the device is off-battery. Check the monitor after charging the device for 5 minutes. 10.2 The image is not clear, how to adjust it? Adjust the diopter adjustment knob until the image is clear. Refer to section 3.1. 10.3 Capturing or recording fails. What's the problem? Check the following items. ● Whether the device is connected to your PC. Capturing or recording is disabled in this status.