Plug & Play Installation manual English edition AGFA Drystar 5300 POWER DECLARATION OF CONFORMITY Drystar 5300 XXXX XX XX XX XX XXXX XXXX XX XX XXXX XX XX XXXX XX XX XXXX XX XX XX XX XX XX XXXX XXXX XXXX XX XX XXXX XX XX XX XX XX XX XXXX XXXX XXXX XX XX XXXX XX XX XX XX XX XX XXXX XXXX XXXX XX XX XXXX XX XX XX XX XX XX XXXX XX XX XX XXXX XX XX XX XXXX XXXX XX XX XX XX XXXX 2923B EN 20031206 User manual Drystar 5300 Reference manual POWER POWER Health Care
❖ The device must only be operated according to its specifications and its intended use. Any operation not corresponding to the specifications or intended use may result in hazards, which in turn may lead to serious injuries or fatal accidents (for example electric shock). AGFA positively will not assume any liability in these cases. ❖ The device must only be installed and put into operation under the specified conditions.
1 A Contents of the packages Unpacking 1 Contents of the packages.
A 2 Remove the packing materials 2 Remove the cardboard box. 3 Remove the foam blocks. 4 Remove the plastic bag. Unpacking 1 Remove the wooden top plate.
3 Remove Drystar 5300 from pallet 2 Remove 2 screws. Unpacking 1 Take 13 mm wrench. A MOBILE or SEISMIC INSTALLATION ONLY: reuse screws to fix printer at its location. 3 Shift printer to the right [1] and lift it 2 2923B EN 20031206 4 Put printer on a table. Align with the table edge. from pallet [2].
A 4 Unpack the accessories Unpacking 1 Check all accessories. Drystar 5300 User manual Drystar 5300 Reference manu al POWER POWER Health Care DECLARATION OF CONFORMITY XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXX XXX XXX XXXX XXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXX XXXXXX XXXXXX XXX XXXX XXXXXX XXXXXX XXXXXX XXXX XXX XXX XXXX XXXXXX XXXX XXX XXXXXX XXX XXXX XXXXXX XXXXXX XXXX XXXXXX Refer to the Packing slip for a complete list of accessories. 2 Check all documents.
1 Environment requirements. 2 Power requirements. ◆ Ventilated room, ◆ away from direct sunlight, ◆ away from sources of dust, humidity, heat and cold, room temperature between 10°C (50°F) and 30°C (86°F), ◆ ◆ B Environment specifications The AC outlet must have either of following specifications: ◆ 100-120 V, 60 Hz, 16/15 A, Installation 5 or ◆ 200-240 V, 50 Hz, 16/15 A. relative humidity between 10% and 80% non-condensing. m m" 0 4 0 2 6 – 600 –24 mm " 3 Space requirements.
Installation B 6 8/16 Remove transport protections (1 of 2) 1 Open top cover. 2 Take wire cutter. 3 Cut 4 red straps. 4 Open hold-down bracket. 5 Remove foam sheet. 6 Close hold-down bracket.
Remove transport protections (2 of 2) 7 Close top cover. 8 Open input tray. 1 2 3 4 5 6 XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXX XXXXXX XXXXXX 9 Remove foam block from input tray. 10 Close input tray.
Installation B 8 Adjust Input block module - 11x14” (1 of 2) 1 Take output tray adjustment tool. 2 Push tool down into output tray holes [1]. Push bracket until it clicks [2]. 1 Click! 2 10/16 3 Take crosshead screwdriver. 4 Remove 3 screws. 5 Lower film positioner unit. 6 Loosen cable.
Adjust Input block module - 11x14” (2 of 2) 7 Push cable into printer housing. B 8 Put and hold film positioner unit into place. Installation 9 9 Remount 3 screws.
Installation B 10 12/16 Connect the cables 1 Select the power cable. 2 Locate the mains connector. 3 Connect the power cable. 4 Locate the network connector and connect the network cable.
C Load film in the input tray (1 of 2) 1 Open input tray. Loading films 11 2 Open film box. 1 2 3 4 5 6 XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXX XXXXXX XXXXXX 3 Take film pack and slide it into the input tray. X XXXX XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXX 4 Remove sticker.
Loading films C 12 Load film in the input tray (2 of 2) 7 Pull plastic tape from around films. XX XXXXXX XXXX XXXXXX XXXX XXXXXX XXXXXX XXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXXXX XXXX XXXX 8 Place film type sticker. XXXXX XXXXXX XX XXXX XXXX XX XX XXXX XXXX X XXX X X X X XXXXX X X X X X X XX XX XXX XXX X X X X X XX XXXX XXXX X XX X X X X X XXXX XX XX XX XXXX XXXX XX XXXX XX XXXX XX XXXX XXXX XX XXXX XXXX XXXX XXX X X X X X XXX XXX XX X X X X X X X XX XXX XX XXXX XXXX XXXX XX XXXX 9 Close input tray.
13 D Startup Drystar 5300 Startup 1 Remove the display protection foil. The film delivered with the printer is intended for test purposes only. 2 Press the POWER button. 3 Wait until READY.
E 14 Configure network settings 1 Select and initiate the printer Network installation wizard. 1x Ask your network manager the following information: 8x 1x Printer IP address: 1. 2. 3. 4. 5. 6. Press the Key-operator key. Press the Down key eight times. Press the Confirm key. Press the Down key. Press the Confirm key. Follow the instructions (see Reference manual). Netmask: Router IP address: 1x Printer AE_Title: Service Host IP address: 2 Select and initiate film calibration. 1x 5x 1. 2. 3.