User's Guide

ENGLISH
1. Charge
2. Pair
3. Connect
Charge the headsets with the included magnetic charging cable. The LED
indicator will turn from red to blue when charging is complete.
While your headsets and cellphone are connected.
Start with your headsets off. Enter pairing mode by pressing and holding
volume+ until ASC100 series says “pairing” and the LED indicator flashes
red and blue.
Open your device’s Bluetooth
®
menu and select “ASC100 series by
AfterShokz”. ASC100 series says “connected” and the LED indicator will
flash blue one time.
PTT/Multifunction
Play/Pause Single click
One
beep
Next song
Double click when
playing music
One
beep
Previous song
Triple click while
playing music
One
beep
Answer call Single click
Two
beeps
End call
Answer the call waiting and
hand up current call
Single click
One
beep
Hold for 2s
One beep
Reject a call Hold for 2s
One
beep
No prompt
Activate voice assistant
Hold for 2s
Call back the last number Double clicks when standby “To call the last number”
Function Action Voice Prompt
Function Action Voice Prompt
How to Set Up ASC100 Series
“Welcome to AfterShokz”
Power ON Press and hold on-off key for 2s
Power OFF
“Power off”
Press and hold on-off key for 3s
Press and hold both buttons for
2s while on a call
Press and hold both buttons for
3s while playing music
Press and hold Volume -
button for 2s
Press Volume + or Volume - button
Mute
“Mute on” or “Mute off”
Switch EQ
“EQ switch”
“Battery high/Battery medium/
Battery low or please charge”
Adjust volume
One beep
Check battery
Status
LED Indicator
Solid red Charging
Solid blue Charging complete
Flashes red and blue Pairing mode
Flashes blue Incoming call
Flashes red every two minutes Low battery
Storage and Maintenance
NFC Function ( Near Field Communication)
Headsets support NFC pairing.
1. Setting headsetstoONmodeorPairingmode.
2. PuttingtheareaofheadsetswithNFCsignclosetoNFCdetectionareaofmobile
phone or wirelessadapter.
3. Blue light will flash one time once headsets were paired successfully, with the voice
notifying “connected”.
Charging Warning System
Headsetshasliquidresiduedetectingfunction.Ifthereisliquidresiduelikesweatonthe
chargingportwhenbeingcharged,headsetswillflashred-bluelight,headsetscorewill
vibratewith “Beep---”warning.Afterliquidresiduebeingremoved,warningwillstop,
headsetscan be charged normally.
Volume + / On-off ; Volume -
· When headsets are paired, music and phone call will be played by headsets.
· When headsets are unpaired, music and phone call will be played by mobile
phone / mobile terminal.
Wearing
Part number
ASC100 20Hz~20KHz
Headsets Specification
Speaker
Frequency
Bone conduction speaker
Bluetooth
®
Version
Microphone type
Dual DSP
noise canceling mic
Bluetooth
®
v5.0
Warranty
Weight
Battery
2 years
32 g
Up to 10 days
2402MHz~2480MHz
4 dBm
A2DP, AVRCP, HSP, HFP
Bluetooth
®
working frequency range:
Maximum RF output power
Continuous play Standby time
Compatible profiles
Battery capacity
Charge voltage
Speaker impedance
5V±5%
8.5ohm±20%
Water resistance IP55
170 mAh
Lithium Battery
Up to 8 hours
Charge time 90 mins
Bluetooth
®
range
10 m
PTT/Multifunction
Microphone 1
Magnetic Charging Port
LED Indicator
Microphone 2
Volume
Power
1. Headsetsshouldbeputincooldryplace,workingintemperaturefrom0to45
degree centigrade. Working in environment supercooled, superheated or
excessivehumiditymaylimittheworkingtimeandshortenthebattery’slife.
2. Afterbeing storedforalongtime,pleasechargeitbeforeuseagain.Playwith
excessive volume may lead distortion of sound, and even hurt your hearing.
3. Please clean headsets with soft dry cloth.
4. Pleasedon’tchargeitimmediatelyafterexercising,incasethesweat residuein
thechargingportdamagetheheadsetscircuit.
5. Keepingthechargingportdrywillreducethepossibilityofdamagingtheheadsets.
Restore Factory Setting
Enter into paring mode, press the PTT/multifunction button, volume +, and volume -
button at the same time for 3 seconds, until you hear the notification tone and feel
the vibration.
Contact Us
3300 N Interstate Hwy 35, Austin, TX 78705, US
www.aftershokz-communications.com
Factory: Shenzhen Voxtech Co., Ltd.
Address: Floors 1-4, Factory Building 26, Shancheng Industrial Park, ShiyanStreet,
Ban'anDistrict, Shenzhen, Guangdong, China
Phone number: 400-6830-858
Our company promises that in normal use, operation and maintenance conditions, we
will gives two years of free warranty. Please contact the local dealer for more help.
Services
Please do not discard the electronic parts together with your daily garbage. In some
countries and regions, departments have been set up to sort and collect discarded
electronic products. Please consult local authorities for more details.
Product Scrap Treatment
User Guide