User's Manual

ManualsBrandsAerohive Networks ManualsElectronicsAccess Point

AP122 Hardware User Guide

Read about and view specifications and compliance information for the AP122 in this topic. Install the

P122 using this topic

The AP122 is optimally suited for coverage-oriented, low-to-medium capacity environments. The AP122

features dual 2x2, 2-stream radios, providing dual 802.11n or 11n/ac performance with data rates up to

867 Mbps using existing 802.3af PoE infrastructure.

For more information about Aerohive APs in general, see "Introduction to Aerohive APs".

For information about connecting your APto the network, best-practices, and troubleshooting, see

"Basic Troubleshooting for New Devices"

Important! Changing the Country Code

If your access point is configured for the World Regulatory Domain, it is important to set the country

code to the country in which the APwill be deployed to meet regulatory requirements and for optimal

wireless operation. To do this, follow these steps:

The country code selection is for World models only and is not available to FCC, CAN, and

other country-specific models. Per FCC regulations, all Wi-Fi products marketed in the

United States must be set to U.S. channels only.

For Devices Running HiveManager:

1. Power on the APand allow it to find and connect to HiveManager. Once the APisconnected, it

appears in the table of unconfigured devices on the Monitor > Devices page and is categorized as

New under the Management Status table header.

2. Select the check box for the AP, and then choose Update > Advanced >Update Country.

3. On the Update Country Code page, choose the appropriate country code from the drop-down

list, and then click Upload.

Page 1 of 1

AP122 Hardware User Guid

201

Summary of content (14 pages)

PAGE 1
AP122 Hardware User Guide Page 1 of 14 AP122 Hardware User Guide Read about and view specifications and compliance information for the AP122 in this topic. Install the AP122 using this topic. The AP122 is optimally suited for coverage-oriented, low-to-medium capacity environments. The AP122 features dual 2x2, 2-stream radios, providing dual 802.11n or 11n/ac performance with data rates up to 867 Mbps using existing 802.3af PoE infrastructure.
PAGE 2
AP122 Hardware User Guide Page 2 of 14 For Devices Running HiveManager NG: 1. Power on the AP and allow it to find and connect to HiveManager NG. Once the AP is connected it appears in the table of devices on the Monitor > Devices page. 2. Select the check box next to the AP, and then choose Assign Country Code from the Actions dropdown list. In the dialog box that appears, select the appropriate country from the drop-down list, and then click Save. 3. Upload your changes to the device.
PAGE 3
AP122 Hardware User Guide Page 3 of 14 EN 301 489-1 V1.9.2: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.2.
PAGE 4
AP122 Hardware User Guide Page 4 of 14 • Slovensko [Slovenian]: [Aerohive] izjavlja, da je ta [AP122] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. • Slovensky [Slovak]: [Aerohive] týmto vyhlasuje, že [AP122] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. • Suomi [Finnish]: [Aerohive] vakuuttaa täten ettät [AP122] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
PAGE 5
AP122 Hardware User Guide Page 5 of 14 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ ISED Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1. l'appareil ne doit pas produire de brouillage, et 2.
PAGE 6
AP122 Hardware User Guide Page 6 of 14 Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et des personnes ou des animaux.
PAGE 7
AP122 Hardware User Guide Page 7 of 14 無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，發射的信號應維持於操作頻帶中。 Taiwan MPE Warning - Aerohive AP122 電磁波曝露量MPE標準值(MPE) 1mW/cm2，送測產品實值為0.196868 mW/cm2 NCC Statement - Aerohive AP122 1. 「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能」。 2. 「低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾」。 3. 「不致造成違反低功率電波輻射性電機管理辦法之所有控制、調整及開關之使用方法」。 4. 「對任何可能造成違反管理辦法規定之調整予以警告，或建議由具有發射機維修專長之技術人員執行或由其直接監督及負責」。 5.
PAGE 8
AP122 Hardware User Guide Page 8 of 14 These devices are intended for indoor use only. Do not install the device in an environment where the operating ambient temperature might exceed the recommended ranges. For products available in the USA/Canada market, for the 2.4 GHz band, only channels 1-11 can be operated. Selection of other channels is not possible.
PAGE 9
AP122 Hardware User Guide Page 9 of 14 Dropped Ceiling Mount The following steps explain how to mount the AP122 on the rail of a dropped ceiling. Make sure that you have all the materials and tools necessary, and familiarize yourself wit the safety and site hazard warnings before you install the device. You may need to drill a small hole in the adjacent ceiling tile to accommodate the cable.
PAGE 10
AP122 Hardware User Guide Page 10 of 14 Removing the Device To remove the device, press the mount clips until they disengage from the rail, then rotate the device and pull it away from the rail. A flat-blade screwdriver will make it easier to access and press the clips. Locking the AP You can secure the AP using a Kensington® lock in the lock slot on the side of the device, or you can use a security bracket and a crosshead screw or a security screw.
PAGE 11
AP122 Hardware User Guide Page 11 of 14 Component Descriptions Status Light The status light conveys operational states for system power, firmware updates, Ethernet and wireless interface activity, and major alarms. The AP122 has a rectangular status light bar on the top corner and down one side of the chassis. The colors of this light bar indicate the following states of activity: Dark: There is no power or the status indicator is disabled.
PAGE 12
AP122 Hardware User Guide Page 12 of 14 Power Connector You can power the AP122 through the ETH0 port from PSE (power sourcing equipment) that is compatible with the 802.3af and 802.3at standards. Because there is no on/off switch, these devices automatically power on when you connect them to power. Ethernet Port The AP122 has one RJ45 10/100/1000Base-T/TX Ethernet port (ETH0) that automatically negotiates half- and full-duplex connections with the connecting device.
PAGE 13
AP122 Hardware User Guide Page 13 of 14 Hardware Specifications The following specifications describe the physical features and hardware components, the power adapter and PoE electrical requirements, and the temperature and humidity ranges in which the devices can operate. Radio Specifications 802.11a • 5.150-5.850 GHz operating frequency • Orthogonal Frequency Division Multiplexing (OFDM) modulation • Rates (Mbps): 54, 48, 36, 24, 12, 9, 6 with auto fallback 802.11b • 2.4-2.
PAGE 14
AP122 Hardware User Guide Page 14 of 14 • One RJ45 (9600 bits per second, 8 data bits, no parity, 1 stop bit, no flow control) • Console serial port: RJ45 (9600 bits per second, 8 data bits, parity: none, 1 stop bit, no flow control • Eth0 Ethernet port: autosensing 10/100/1000Base-T/TX Mbps, with IEEE 802.3af- or 802.