user manual amp one r Register you amp one: ps.com www.
amp one user manual Contents 1. Introduction 3 2. Safety Instructions 4 3. Controls and Connections 4 3.1 Front Side 4 3.2 Rear Side 5 4. Starting-up 6 4.1 Cabling and Switching-on 6 4.2 Level Adjustment 6 5. Functional Characteristics 7 5.1 Mute 7 5.2 Tone Control Networks 7 5.2.1 colour 7 5.2.2 bass boost 7 5.2.3 parametric equalizer 5.2.4 tone balance 2 Page 7 7-8 5.3 Compressor 8 5.4 Rear Side Features 9 6. Technical Specifications 10 7.
1. Introduction Welcome to B! Thank you for choosing the amp one out of the AER bottom-lineseries. This series has been specially developed for the modern bass player who values performance, versatility and easy handling. Please take a few minutes to read through these instructions. We want you to understand just what the amp one can do and how to set it up so that you can get maximum benefit out of it.
2. Safety Instructions The following instructions help to minimize the risk of injury through fire and electric shock. 7. Never install your device close to devices with strong electromagnetic fields such as large mains transformers, electrical motors, neon illumination etc. Do not lay signal cables parallel to power current cables. 1. Read these safety instructions carefully prior to using the device. 8. There are no user-serviceable components inside your device.
16) threshold 17) ratio 18) active 19) on/off treshold control input signal compression ratio control compressor active mode indicator compressor activation switch: 20) master 21) power master level control on/off status indicator electric bass amp compressor deactivated acitve amp one bottom line power on headphones 2 sub out 4 send 6 insert pre eq 8 aux in aux level gnd lift 3 line out 5 footswitch 7 return 9 insert post eq DI 16 10 12 1 di level 11 pre/post 14
4. Starting up 4.1 Cabling and Switching on Before connecting to the mains, please ensure that your local mains voltage is suitable for the voltage of the device (e.g. 120V in the USA, 230V in Europe). The relevant specs and safety symbols are printed on the rear side of the unit. Connect all cables as desired and switch the amplifier on. The green power control LED indicates operational readiness. 4.
5. Functional Characteristics 5.1 Mute The mute switch turns the appliance to mute as required. The function can also be activated by a standard footswitch (on/off switch). 5.2 Tone Control Networks As with all AER products, the amp three is fitted with an excellent basic tone thanks to the selection of components, circuits and pre-equalizations. In addition, various equalizer networks enable you to adjust the basic tone to suit your personal requirements.
level If you turn the balance control to the left (Fig. 2), the bass range is further increased, but the treble is decreased by max. 0dB. intensity max 5.3 Compressor A compressor is an electrical circuit (a device) which you can use to influence the dynamic behaviour of a signal. The aim can be, for example, to minimise the risk of distortion. In use the signal level change can be kept constant at a set ratio from a set threshold. The following figure illustrates the correlation.
2 4 6 8 10 14 15 12 1 3 5 7 9 5.4 Rear Side Features 11 13 7) return The ground lift switch separates the earth conductor from the signal ground and suppresses humming. Being part of the effect loop path, return represents the input for an external effect device (from the output of the effect device). Return on it’s own may also be used as quasi auxiliary signal input (-10 dbV).
Technical data 6. Technical Data Inputs (notes 1, 4) input tone balance High-impedance instrument input Mono jack, ¼” (6.35 mm) Sensitivity: 21 mV (-34 dBV) Impedance: 1 Megohm Equivalent input noise: 1.4 μV (–117 dBV), A-weighted balance left: +12 dB at 50 Hz balance center: +9 dB at 50 Hz, and +10 dB at 10 kHz high / low switch: 10 dB attenuation balance right: –2 dB at 50 Hz, and +11 dB at 10 kHz clip indicator: 8 dB headroom aux in return Stereo jack, ¼ “ (6.
INPUT HIGH/LOW PREAMP R T GAIN T TUNER INSERT PRE EQ R MUTE MUTE CLIP DETECTION FOOT SWITCH OFF/ON COLOUR MIDDLE BANDWIDTH BASS FREQ TREBLE AUX IN R R T INSERT POST EQ OFF/ON T RETURN BASS BOOST SEND EXT.
www.aer-amps.