Installation Manual

ManualsBrandsAeon Stands and Mounts ManualsAccessories & SuppliesFull Motion TV Wall Mount with 32 inch Long Extension for 42 to 80 inch TVs

Features:

▪ Designed for 42”-80” Flat panels

▪ VESA Compliant: Up to 800x600mm

▪ Maximum weight capacity up to 150 lbs

▪ Lift and lock for easy installation

▪ U-cap system for clean and simple cable management

▪ U p 5° and Down 15° of easy tilt

▪ Three pivot points with up to 180° swivel

▪

Horizontal movement feature allows for lateral shift

Full Motion TV Wall Mount

with Long Extending Arm

AEON-45200 AEON-45250

AEON-45250

(24” OC Studs)

AEON-45200

(16” OC Studs)

Installation Instructions

Summary of content (7 pages)

PAGE 1
AEON-45200 AEON-45250 Full Motion TV Wall Mount with Long Extending Arm AEON-45200 (16” OC Studs) Features: AEON-45250 (24” OC Studs) ▪ Designed for 42”-80” Flat panels ▪ VESA Compliant: Up to 800x600mm ▪ Maximum weight capacity up to 150 lbs ▪ Lift and lock for easy installation ▪ U-cap system for clean and simple cable management ▪ U p 5° and Down 15° of easy tilt ▪ Three pivot points with up to 180° swivel ▪ Horizontal movement feature allows for lateral shift Installation Instructions
PAGE 2
AEON-45200 AEON-45250 Full Motion TV Wall Mount with Long Extending Arm 31.
PAGE 3
! WARNING PLEASE NOTE: IMPROPER INSTALLATION WILL VOID WARRANTY. Please do not begin installation until you have thoroughly read and understood these instructions. Improper installation may cause serious injury and/or damage. It is recommended that a qualified contractor install the AEON-45200 / AEON-45250 Full Motion Mount . Make sure that the wall you plan to use will safely support four times the combined weight of the mounted equipment, including its accessories.
PAGE 4
Step1 Mounting the mount arm assy A. Mounting to Wood Studs 16" or 24" The AEON-45200 / AEON-45250 Full Motion mount can be mounted onto two wooden studs, with center to center distances between 16"and 24". Using an electronic stud finder (Fig.1),locate the center of the two wooden studs at the desired mounting location. Mark the stud center positions directly on the wall.
PAGE 5
Step 2 Assemble the Adaptor Plate Adaptor rail Adaptor bracket (M/Nx4) Slider plate (C) Philips head screw M6*15mm Metal washers Φ6 Fig.3 Select from Mounting Screws Metal washer Ø6 Adaptor Bracket Insert Slider plate(M/Nx4) into adaptor rails, then insert the adaptor bracket into adaptor rail, fix adaptor bracket and slider plate with four philips head screw M6*15mm ( C ) and four metal washers Φ 6 ( G ) using Philips headcrew driver as shown Fig.3.
PAGE 6
Step 4 Using Cable Management The AEON-45200 /AEON-45250 includes a cable management system where cable can be routed along the length of the arm assembly. Route the display cable along the entrance of the cable management slot.(Fig.6) U-Cap Cable management Cable Note: For optimal performance, route the AC power cable separately form the signal cables. With all cables in place, pull the display in and out to be certain that the arm assembly moves freely, without stretching or damaging the cables. Fig.
PAGE 7
Step 5 Swivel - Adjust the flat panel display for off center viewing positions. Grasp the side edges of the display and then swivel display into its desired position (Fig.11). Fig.11 Panning - Positions the flat panel display at an angle to the wall for viewing from opposite sides of the room. Grasp the side edges of the display and then swivel and pull the display into desired position (Fig.12). Fig.12 Retracting the Flat Panel Display - Positions the display against the wall.