Technical data

ManualsBrandsAeon Labs ManualsRemote ControlsMinimote Black

AEO_MREM_B

Aeonlabs Minimote black

Firmware Version : 1.0

Quick Start

R This device is a Z-Wave Remote Control.

Use Network Management Buttons to include and exclude devices to the remote controls network and use the LEARN button to

include the minimote into a different network. Pushing the LEARN button for 5 sec will wake up the device.

Please refer to the chapters below for detailed information about all aspects of the products usage.

Product description

The Aeon Labs mini remote control can control a variety of Z-Wave compatible devices such as switches, dimmers, window blinds

and motion sensors. The device can include and exclude devices, group them and set and release associations. The mini remote

only offers four control buttons for scene selection. Behind a slider there are four more buttons for Z-Wave network control. A non-

replaceable but rechargeable battery powers the remote control. Recharging is done on a conventional USB bus using the charging

cable provided. The product is in the color black.

Installation Guidelines

The device is ready for use. In case there are no LED signals when hitting the buttons the device needs to be recharged using the

USB cable provided.

Summary of content (7 pages)

PAGE 1
AEO_MREM_B Aeonlabs Minimote black Firmware Version : 1.0 Quick Start R This device is a Z-Wave Remote Control. Use Network Management Buttons to include and exclude devices to the remote controls network and use the LEARN button to include the minimote into a different network. Pushing the LEARN button for 5 sec will wake up the device. Please refer to the chapters below for detailed information about all aspects of the products usage.
PAGE 2
Behavior within the Z-Wave network I On factory default the device does not belong to any Z-Wave network. The device needs to join an existing wireless network to communicate with the devices of this network. This process is called Inclusion. Devices can also leave a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller will be turned into exclusion respective inclusion mode.
PAGE 3
1 Scene 1 (max. nodes in group: 5) 2 Scene 2 (max. nodes in group: 5) 3 Scene 3 (max. nodes in group: 5) 4 Scene 4 (max. nodes in group: 5) Set and unset associations to actuators Associations can be assigned and remove either via Z-Wave commands or using the device itself. SA 1. Press the scene button the new device shall be associated with and keep this button pressed. 2. Issue a Node Information Frame from the target device. This is usually done by single or triple click a button.
PAGE 4
Shift Primary Role to a different Controller The device can hand over its primary role to another controller and become secondary controller. The primary shift is initiated on the device by pressing the "Learn" button. Set association between two device in Z-Wave network CA The controller is able to set association between two other devices in the network. The controller is turned into an association mode both devices are announced by pressing a button.
PAGE 5
Learn Mode Mode of Button 2 (upper right) (Parameter Number 242, Parameter Size 1) Defines the switching mode of Button 2 Value Description 0 Factory Default (Default) 1 Scene Mode 2 Add Mode 3 Remove Mode 4 Association Mode 5 Learn Mode Mode of Button 3 (lower left) (Parameter Number 243, Parameter Size 1) Defines the switching mode of Button 3 Value Description 0 Factory Default (Default) 1 Scene Mode 2 Add Mode 3 Remove Mode 4 Association Mode 5 Learn Mode Mode of Button 4
PAGE 6
0 Factory Default (Default) 1 Scene Mode 2 Add Mode 3 Remove Mode 4 Association Mode 5 Learn Mode Mode of Button 6 (marked as Exclude) (Parameter Number 246, Parameter Size 1) Defines the switching mode of Button 6 Value Description 0 Factory Default (Default) 1 Scene Mode 2 Add Mode 3 Remove Mode 4 Association Mode 5 Learn Mode Mode of Button 7 (marked as Association) (Parameter Number 247, Parameter Size 1) Defines the switching mode of Button 7 Value Description 0 Factory Def
PAGE 7
5 Learn Mode Technical Data Explorer Frame Support Yes SDK 4.50 beta Device Type Slave with routing capabilities Generic Device Class Binary Switch Specific Device Class Binary Power Switch Routing Yes FLiRS No Firmware Version 1.0 7 (c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, www.zwaveeurope.