User's Manual
Aeotec by Aeon Labs LED Strip.
1
3
4
Aeotec LED Strip is a multi-coloured LED Strip which allows
control (on/off/dim/colour change) via wireless Z-Wave
commands.
The LED Strip can also communicate securely via AES 128
wireless Z-Wave commands and supports Over-The-Air (OTA)
rmware upgrades.
Package Contents:
1.
2.
3.
1.
2.
3.
Plug the LED strip to the LED strip connector of your LED
Strip Controller.
Connect the Power Adapter to your LED Strip.
Plug the Adapter into an electrical outlet and then the
Set your Z-Wave controller into pairing mode.
Press the Action Button on the LED Strip.
If the LED Strip has been successfully added to your Z-Wave
network, its Network LED will be solid. If the pairing was
unsuccessful, the red LED will be on for 2 seconds and then
remain a colourful gradient, repeat the instructions above
from step 1.
Familiarise yourself with your LED Strip.
Quick start.
With your LED Strip now working as a part of your smart home,
you’ll be able to congure it to indicate different colours from your
home control software via setting the RGB value. Please refer to
the user manual for your Z-Wave controller/gateway for precise
instructions on conguring your LED Strip to your needs.
Your LED Strip can be removed from your Z-Wave network
at any time. You’ll need to use your Z-Wave network’s main
controller. To set your Z-Wave controller/gateway into removal
mode, please refer to the respective section within your Z-Wave
controller instruction manual.
Install your LED Strip.
7 6 5 4 3 2 1 0
Value 1 (MSB)
Colour
Transition Style
Colour Change
Speed Option
Colour Display
Cycle
Value 2 Brightness
Value 3 Cycle Count
Value 4 (LSB)
Time Base of Coulor
Change Speed
Colour Change Speed Level
Removing your LED Strip from a Z-Wave network.
Advanced functions.
Colour Display Cycle Configuration.
Parameter 37 [4 byte] will cycle the colour displayed by LED
Strip into different modes:
The Colour Display Cycle field can have the following values
corresponding to 4 different modes:
The Cycle Count is used to dene the number of repetitions/
cycles displayed by your LED Strip in Colour Display Cycle
before stopping.
Colour Display Cycle (4 bits)
The following values correspond to 2 different transition styles
between colours:
Cycle Count (8 bits)
Colour Display
Cycle
Description
0 Inactive (keep the current conguration values)
1
Rainbow Mode(red, orange, yellow, green, cyan, blue,
violet)
2
Multi Colour Mode(colours cycle between selected
colours)
3 Random Mode.
4 Single Colour Mode.
5 to15 Reserved.
Colour
Transition Style
Description
0 Smooth Colour Transition.
1 Fade Out Fade In Transition.
Cycle Count Description
0 Unlimited.
1 to 254 Total number of repetitions/cycles before stopping.
255 Inactive (keep the current conguration values).
Colour Transition Style (2 bits)
This function would be used when the Colour Transition Style is
set to Fade Out/In.
The table above shows a decimal representation of the settings
that can be set on parameter 37.
This function would be used when the Colour Transition Style is
set to Fade Out/In.
Time Base of Colour Change Speed (3 bits)
Colour Change Speed Level (5 bits)
Speed Level Description
0 Constant speed.
1 to 30 Accelerate/decelerate speed from the level 1 to 30.
31 Inactive (keep the current conguration values).
Parameter 39 [4 byte] can be used to set up to 8 colours to
cycle between when LED Strip is in Multi Colour Mode. Colours
transition from Colour Index 1-8.
2
Brightness Level Description
1 to 99 1 = Min level. 99 = Max level.
0 or 255 Inactive (keep the current conguration values).
Brightness (8 bits)
Time Base Description
0 Time base is 1s.
1 Time base is 10ms.
2 Time base is 100ms.
1.
2.
Set your Z-Wave controller into device removal mode.
Press the Action Button on the LED Strip.
7 6 5 4 3 2 1 0
Value 1 (MSB) Index 1 Index 2
Value 2 Index 3 Index 4
Value 3 Index 5 Index 6
Value 4 (LSB) Index 7 Index 8
View the expanded manual:
http://aeotec.com/support
LED Strip
IMPORTANT!
This product has been fully tested and certied to work with
Z-Wave by the Z-Wave Alliance. It is crafted using Z-Wave
Plus, the latest device version of Z-Wave. As such, if the
product does not work with your gateway, please be sure
to check with your gateway manufacturer that they have
integrated this device with their gateway for full operation.
LED Strip Controller Back Mount Plate
Screws
Double-Sided Tape
1. LED Strip Controller (×1)
2. Screws (×2)
3. Back Mount Plate (×1)
4. 5 meters LED strip (×1)
5. Power Adapter (×1)
6. Double-Sided Tape (×1)
Adding your LED Strip to a Z-Wave network.
You are now able to manually control the LED Strip directly
via pressing your LED Strip’ Action Button. It is time to add
your LED Strip to your Z-Wave network. To set your Z-Wave
gateway/controller into pairing mode, please refer to the
respective section within your controller instruction manual.
Power Adapter
The installation of your LED Strip has two major steps: the LED
Strip Controller and the LED Strip. LED Strip can be installed
inside or outside your home, but the LED Strip Controller should
only be installed inside your home and should not be installed
outdoors in elements such as rain and snow.
Network LED
Action Button
Power Input
LED Strip Connector
LED Strip
If the LED Strip has been successfully removed from your
Z-Wave network, its Network LED will remain colourful
gradient. If the removal was unsuccessful, the Network LED
will still be solid, repeat the instructions above from step 1.
LED Strip
LED Strip Controller
Power Socket
4.
Network LED on LED Strip Controller will blink slowly to
indicate it is ready to be paired to your Z-Wave network.
Now press the Action Button to toggle your LED strip on or
off to ensure the connections between your LED Strip and its
Controller properly connected.
3.
Power Adapter