User's Manual

View the expanded manual:
http://aeotec.com/support
Aeotec by Aeon Labs Door Window Sensor.
1 3
The Aeotec by Aeon Labs Door/Window Sensor 6 provides your Z-Wave network
with the security intelligence required for a modern home automation and security
system. And It does it all in a smaller, more elegant design crafted to suit any
home's decor.
The Door Window Sensor is also a security Z-wave device that supports Over
The Air (OTA) for rmware updates.
The installation of your Door Window Sensor has two major steps: the Main
Sensor and the Magnet. Your Door Window Sensor will use wireless technology
to talk to your Z-Wave network once paired to your Z-Wave network.
Selecting where you'll place your Door/Window Sensor in your home is just as
important as the actual afxing it to the surface.
Whether it’s for security or intelligence purposes, your sensor:
1.
2.
3.
4.
1.
2.
1.
2.
3.
4.
Should be afxed indoors and away from sources of moisture.
Placed within 30 meters of another Z-Wave device that is either a gateway or
not powered by batteries.
The magnet and the main sensor must be less than 1.6cm apart for the small
magnet installation or 2.5cm apart for the big magnet installation. Main sensor
must be affixed to the door or window and the magnet must be affixed to
the frame. The magnet and the main sensor must separate when the door or
window is opened.
Should not be mounted on a metal frame.
Let your Z-Wave primary controller/gateway enter into adding/inclusion mode.
Take your Sensor near to your primary controller.
Press the Action Button once on your Sensor. The green LED will blink.
If your Door Window Sensor has been successfully added to your Z-Wave
network, its green LED will be solid for 2 seconds and then the orange LED will
fast blink for 10 minutes if the Sensor does not receive the Wake Up No More
info Command from Controller. If the adding was unsuccessful and the red
LED will be solid for 2 seconds and then off, repeat the above steps.
Familiarize yourself with your Door Window Sensor.
Quick start.
With your mounting plates prepared to hold each component of your sensor, it’s
time to add it to your Z-Wave network.
With your Sensor added to the Z-Wave network. It’s now time to insert the main
unit into the corresponding sensor plate.
Put the main unit in the top-left direction on the Back Mounting, and then push
the Sensor into the Back Mounting Plate, as the gure below shows.
After the installation is complete, you can also paint on the Door Window Sensor
to match with the door colour and let them look like a whole unit.
With your Sensor now working as a part of your smart home, you’ll be able to
congure it from your home control software or phone application. Please refer
to your software’s user guide for precise instructions on configuring the Door
Window Sensor to your needs.
Afx your Back Mounting Plate and Magnet to a surface.
The Back Mounting Plate can be afxed using screws or double-sided tape and
should be mounted on the apex angle of the door. The Magnet must be afxed
using double-sided tape and can’t exceed the valid range, see the gure below.
There are 2 types of Magnets (Magnet 1: 30mm×6mm×2mm, Magnet 2:
30mm×10mm×2mm) , the size of magnet 2 is a little larger than magnet 1, so
the magnetism of magnet 2 is stronger than the magnet 1.
You can choose to install each one of magnet on the door frame according to
your need or the distance between the door and frame, see the gure below.
When the Back Mounting Plate is affixed by the double-sided tape, wipe the
two surfaces clean of any oil or dust with a damp towel. When the surface
has completely dried, peel one side of the tape back and attach it to the
corresponding section on the rear side of the Back Mounting Plate.
Note:
Adding your Sensor to your Z-Wave network.
Attach your Sensor to its Back Mounting plate.
Installing your Door Window Sensor.
Package contents:
1. Sensor Unit.
2. Back Mounting Plate.
3. Magnet Unit (×2).
4. Double-Sided Tape(×2).
5. Screws (×3).
6. USB cable.
1
7.2cm
3.0cm
2 3
654
Action Button
Micro USB Port
RGB LED
2
Magnet 2 Magnet 2Magnet 1
CORRECT WRONG
Magnet 1
Max 1.6cm Max 2.5cm
Max 1.9cm Max 1.6cm
MagnetMagnet
Frame
OR
OR
Recessed in the crack of the door.Mounted on the surface of frame.
Must avoid children to contact with the Magnets and avoid the magnets are
swallowed by children.
3.
4
1.
2.
Remove your Sensor unit from its Back Mounting Plate, press the Action
Button on the back of the Sensor unit and then release the Action Button.
This will trigger and send a wake up notication command to your controller/
gateway.
If you want your Sensor to keep awake for a longer time, press and hold the
Action Button on the back of the Sensor unit for 3 seconds, then your Sensor
will wake up for 10 minutes and the orange LED will fast blink while it is awake.
In order to send your Sensor new conguration commands from your Z-Wave
controller or gateway, it will need to be woken up.
Send a wake up notification.
Advanced functions.