User's Manual

View the expanded manual:
http://aeotec.com/support
Plug
Aeotec by Aeon Labs Smart Switch.
Aeotec Smart Switch is a low-cost Z-Wave Switch plug-
in module specically used to enable Z-Wave command
and control (on/off) of any plug-in tool. It can report
immediate wattage consumption or kWh energy usage
over a period of time. In the event of power failure, non-
volatile memory retains all programmed information
relating to the unit’s operating status.
Its surface has a Smart RGB LED, which can be used
for indicating the output load status or strength of the
wireless signal. You can congure its indication colour
according to your favour.
The Smart Switch 6 is also a security Z-wave device and
supports Over The Air (OTA) feature for the products
rmware upgrade.
®
Familiarize yourself with your Smart Switch.
Getting your Smart Switch up and running is as simple
as plugging it into a wall socket and linking it to your
Z-Wave network. The following instructions tell you how
to link your Smart Switch to your Z-Wave network via
Aeotec by Aeon Labs’ Z-Stick or Minimote controller.
If you are using other products as your main Z-Wave
controller, such as a Z-Wave gateway, please refer to
the part of their respective manual that tells you how add
new devices to your network.
If you’re using a Z-Stick:
Quick start.
2.
3.
4.
5.
6.
7.
1. Decide on where you want your Smart Switch to be
placed and plug it in to a wall outlet. Its purple LED
will begin to blink.
If you’re using a Minimote:
1.
2.
3.
4.
5.
6.
Decide on where you want your Smart Switch to be
placed and plug it in to a wall socket. Its purple LED
will begin to blink.
Take your Minimote to your Smart Switch.
Press the Include button on your Minimote.
Press the Action Button on your Smart Switch.
If Smart Switch has been successfully linked to your
Z-Wave network, its RGB LED will no longer blink.
If the linking was unsuccessful and the purple LED
continues to blink repeat the instructions from step 3.
Press any button on your Minimote to take it out of
installation mode.
With your Smart Switch now working as a part of your
smart home, you’ll be able to configure it from your
home control software. Please refer to your software’s
user guide for precise instructions on conguring Smart
Switch to your needs.
The colour of RGB LED will change according to the
output load power level when it is in Energy mode:
Version LED indication Output (W)
US Green [0W, 800W)
Yellow [800W, 1500W)
Red [1500W, ∞)
AU Green [0W, 1000W)
Yellow [1000W, 2000W)
Red [2000W, ∞)
EU Green [0W, 1500W)
Yellow [1500W, 3000W)
Red [3000W, ∞)
You can also configure the brightness of RGB LED
when the RGB Bulb is in Energy mode, Momentary
Indicate mode, or Night Light mode.
Your Smart Switch can be removed from your Z-Wave
network at any time. You’ll need to use your Z-Wave
network’s main controller to do this and the following
instructions will tell you how to do this using a Aeotec
by Aeon Labs’ Z-Stick or Minimote controller. If you are
using other products as your main Z-Wave controller,
please refer to the part of their respective manuals that
tells you how remove devices from your network.
Removing your Smart Switch from a Z-Wave
network.
If you’re using a Z-Stick:
1.
2.
3.
4.
5.
6.
If your Z-Stick is plugged into a gateway or a
computer, unplug it.
Take your Z-Stick to your Smart Switch.
Press the Action Button on your Z-Stick.
Press the Action Button on your Smart Switch.
If your Smart Switch has been successfully removed
from your network, its RGB LED will blink. If the
removal was unsuccessful, the RGB LED will not
blink.
Press the Action Button on the Z-Stick to take it out of
removal mode
If you’re using a Minimote:
1.
2.
3.
4.
5.
Take your Minimote to your Smart Switch.
Press the Remove Button on your Minimote.
Press the Action Button on your Smart Switch.
If your Smart Switch has been successfully removed
from your network, its RGB LED will blink. If the
removal was unsuccessful, the RGB LED will not
blink.
Press any button on your Minimote to take it out of
removal mode.
If your Z-Stick is plugged into a gateway or a
computer, unplug it.
Take your Z-Stick to your Smart Switch.
Press the Action Button on your Z-Stick.
Press the Action Button on your Smart Switch.
If Smart Switch has been successfully linked to your
Z-Wave network, its RGB LED will no longer blink.
If the linking was unsuccessful and the purple LED
continues to blink repeat the instructions from step 4.
Press the Action Button on the Z-Stick to take it out of
installation mode and then return it to your gateway
or computer.
Changing LED mode.
You can change the mode of how the LED acts through
configuring the Smart Switch. There are 3 different
modes: Energy mode, Momentary indicate mode, and
Night light mode.
Advanced functions.