User Manual

Aeon Labs Micro Smart Energy Illuminator
(In-Wall Z-Wave Dimmer Module w/ Energy Monitor)
Introduction:
The Aeon Labs Micro Smart Energy Illuminator is a low-cost
Z-Wave dimmer module specifically used to enable Z-Wave
command and control (on/off/dim) for existing in-wall
switches. It can also report immediate wattage
consumption or kWh energy usage over a period of time.
The wireless module is powered from the mains supply and
is a three-wire design which requires a neutral connection.
In the event of power failure, non-volatile memory retains
all programmed information relating to the units operating
status.
It also is a repeater in the Z-Wave network. Acting as a
bridge for communication, it will forward Z-Wave command
messages to their destinations if the originating controller is
out of range from the destination node.
By taking advantage of the Z-Wave mesh network,
commands can be routed to their destination via
intermediary “listening” Z-Wave products. Products that
are Z-Wave certified can be used and communicate with
other Z-Wave certified devices.
In-Wall Electrical Installation Instructions
:
IMPORTANT: A licensed electrician with knowledge and
understanding of electrical systems and electrical safety
should complete the electrical installation inside the main
circuit box (usually located outside of your house).
IMPORTANT:
The electricity to the circuit must be shut off
during installation for safety and to ensure that wires are
not shortcircuited during insallation which will cause
damage to the Micro Module.
The Aeon Labs Micro Smart Energy Illuminator must first be
powered by a 3-wire system in order to operate. The wiring
diagram is as follows:
Z-Wave Network Instructions:
The Aeon Labs Micro Smart Energy Illuminator must be
paired (included) into a Z-Wave network before it can
receive Z-Wave commands to turn on/off/dim and report
its energy usage. The Smart Energy Illuminator can only
communicate to devices within it’s own Z-Wave network.
Note: The LED on the Micro Smart Energy Illuminator will
blink if it is currently not paired into a Z-Wave network.
• Adding/Including/Pairing the Micro Smart Energy
Illuminator into a Z-Wave Network
1. Press the button labeled “Include” on the Aeon Labs
Minimote to begin the Z-Wave inclusion process.
Note: To include the Aeon Labs Micro Smart Energy
Illuminator with other controllers, please consult the
operation manual for these controllers on how to
include Z-Wave products into an existing network.
For instructions on select partner gateways, visit
www.aeon-labs.com/support.
2. While the Micro Smart Energy Illuminator is powered
in a 3-wire system, press the button located near the
Status Indication LED. Or alternatively, the external
switch/button control can be pressed 6 times in quick
succession.
Troubleshooting: If the Aeon Labs Micro Smart Energy
Illuminator was not successfully included into any Z-Wave
network, the LED will be blinking slowly continually. If the
Aeon Labs Micro Smart Energy Illuminator was successfully
included to a Z-Wave network, the Status Indication LED will
either be solid on or off (depending on if the switch is on or
off) 10 seconds after the button was last pressed.
• Removing/Resetting the Micro Smart Energy
Illuminator from your Z-Wave Network
1. Press the button labeled “Remove” on the Aeon Labs
Minimote Stick to begin the Z-Wave removal process.
Note: To include the Aeon Labs Micro Smart Energy
Illuminator with other controllers, please consult the
operation manual for these controllers on how to
include Z-Wave products into an existing network.
For instructions on select partner gateways, visit
www.aeon-labs.com/support.
2. While the Micro Smart Energy Illuminator is powered
in a 3-wire system, press the button located near the
Status Indication LED. Or alternatively, the external
switch/button control can be pressed 6 times in quick
succession.
Troubleshooting: If the Aeon Labs Micro Smart Energy
Illuminator was removed from the Z-Wave network, the
Status Indication LED will be blinking. If the Aeon Labs
Smart Energy Illuminator was not successfully removed
from the Z-Wave network, the Status Indication LED will
either be solid on or off (depending on if the switch is on or
off) 10 seconds after the button was last pressed.
• Turning On/Off/Dim the Micro Smart Energy
Illuminator
Use any of the below methods to turn on/off or dim the
power through the Micro Smart Energy Illuminator.
o Pressing the button on the external (Wall)
switch will be able to toggle power flow (on/off)
through the Smart Energy Illuminator (2-state
flip/flop switch). If the mode of the micro
module is set to momentary push button,
holding the push button will dim the lights and a
short press will toggle the lights between on/off.
- 1 - - 2 - - 3 - - 4 -