EN User Manual Washer Dryer L ÖKO HWD
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 5 3. PRODUCT DESCRIPTION.............................................................................................. 7 4. CONTROL PANEL...........................................................................................................8 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • • side, where the appliance door can not be fully opened. Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. Ensure you have good ventilation in the installation room to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.
ENGLISH • • • • • • • • 5 Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the wash dryer. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. Remove all objects from pockets such as lighters and matches.
www.aeg.com 2.2 Electrical Connection WARNING! Risk of fire and electrical shock. • The appliance must be earthed. • Always use a correctly installed shockproof socket. • Do not use multi-plug adapters and extension cables. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • Do not touch the mains cable or the mains plug with wet hands. • Only for UK and Ireland: The appliance has a 13 amp mains plug.
ENGLISH 3. PRODUCT DESCRIPTION 3.1 Appliance overview 1 2 3 10 4 11 12 5 6 13 7 9 8 1 2 3 4 5 6 7 8 Worktop Detergent dispenser Air filter(s) Control panel Door handle Rating plate Drain pump filter Feet for the appliance level 3.2 How to activate the child safety device This device prevents children or pets to be closed in the drum. Turn the device clockwise, until the groove is horizontal. You cannot close the door.
www.aeg.com 3.3 Accessories 1 2 4 3 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink. 4. CONTROL PANEL 4.1 Control panel description 1 2 WA S C H E N 3 WASCHEN/TROCKNEN Feinwäsche Koch/Bunt Leichtbügeln Baumwolle Eco Super Eco 20 Min.
ENGLISH 4.2 Display A K J B I H G C F D E The display shows: A The text bar: • Guides you in the use of the appliance. • Shows the programme status and phase. • Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child safety lock Door locked C You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off.
www.aeg.com Digit area Time of the day When you activate the appliance the display shows the time of the day for some seconds. To adjust the clock, refer to "Clock setting". Programme duration When you set the programme, the cycle duration is displayed for a few seconds then, the time of the programme end appears again. Programme duration indicator The indicator comes on when the digits shows the programme duration.
ENGLISH Time save The indicator comes on when you set one of the programme duration. F Shortened time Extra Quick G Indicator for air filters Extra rinsing H The value shows the total number of the rinses. The indicator bar fills accordingly the numbers of rinses. Stain indicator Prewash indicator I Soak indicator The indicator bar fills accordingly to the set functions. Spin speed of the set programme J No Spin indicator1) Rinse Hold indicator 1) Only available for SPIN/DRAIN programme.
www.aeg.com 5. PROGRAMMES 5.1 Programme Chart Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Washing/Drying programmes1) Koch/Bunt 95°C - Cold Baumwolle Eco2) 60°C - 40°C Pflegeleicht 60°C - Cold Wolle/Seide 40°C - Cold Anti-Allergie 60°C 9 kg 1600 rpm White cotton and coloured cotton. Normal soil and light soil. 9 kg 1600 rpm White cotton and colour-fast cotton. Normal soil.
ENGLISH Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Super Eco Cold 3 kg 1200 rpm Mixed fabric (cotton and synthetic items).5) 20 Min. - 3 kg 40°C - 30°C 3 kg 1200 rpm Cottons and synthetics items with light soil level or worn only once. 9 kg 1600 rpm To rinse and spin the laundry. All fabrics. 9 kg 1600 rpm To spin the laundry and to drain the water in the drum. All fabrics.
www.aeg.com Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) up to 1.5 kg Steam programme for cotton and synthetic items. This cycle removes odours from the laundry.9) Auffrischen 40°C 1) When you set a Washing / Drying programme, the display tells you that the drying cycle is not set. If you want to dry your laundry, set an automatic drying or a timed drying.
ENGLISH Programme U./ Min. 20 Min. - 3 kg ■ Spülen ■ Schleudern/Pumpen ■ PreStains wash Soak Extra Spü- Zeit Spa- len 1) ren2) 15 Zeitvorwahl ■ ■ ■ ■ ■ ■ 1) If the Permanent Extra Rinse option is activated, the appliance adds some additional rinses. In the Rinse programme, if you set a low spin speed the appliance performs delicate rinses and a short spin. 2) If you set a shorter duration, we recommend that you decrease the quantity of the load.
www.aeg.com Dryness Level Type of fabric Cupboard Dry For items to put away Synthetics and mixed fabrics (jumpers, blouses, underwear, household linen) 4 1200 155 - 165 2 1200 55 - 65 Iron Dry Suitable for ironing Cottons and Linen (sheets, tablecloths, shirts, etc) 6 1600 190 - 200 3 1600 70 - 80 1 1600 30 - 40 1 1200 80 - 100 Wool dry Wool (wool jumpers) 5.
ENGLISH 17 At programme start the display shows the duration programme for the maximum load capacity. During the washing phase the programme duration is automatically calculated and can be greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton 60°C, maximum load capacity 9 kg, the programme duration exceeds 2 hours; real load 1 kg, the programme duration don’t reach 1 hour). When the appliance is calculating the real programme duration a dot blinks in the display.
www.aeg.com • To activate/deactivate this function touch Zeit Sparen and Zeitvorwahl at the same time until the display show the indicator off. comes on/goes 8. OPTIONS 8.1 Touch Screen Make sure the touch screen and buttons are always clean and dry. 8.2 Ein/Aus Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated.
ENGLISH 19 8.10 Extra Spülen 8.12 U./Min. Touch this button to add rinsing phases to a programme. Touch button U./Min. to: • Decrease the maximum speed of the spin phase of the programme. Use this function for persons allergic to detergents and in areas where the water is soft. 8.11 Flecken/Vorwäsche Touch this button to set one of the following functions: • Prewash Use this function for heavy soil. The appliance adds a prewash phase to the main wash. The programme duration increases.
www.aeg.com The minute digits flash. 4. Turn the programme knob to change the minutes. 5. Touch Start/Pause button to confirm the selection. 9.3 Language setting The first time you activate the appliance, the display shows the default language and tells you to confirm it or change it: 1. Turn the programme knob to set the desired language. 2. When the display shows the necessary language touch Start/ Pause button to confirm the selection. 9.4 Change the language after the first activation 1.
ENGLISH 10.4 Filling the detergent and additives Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Flap for powder or liquid detergent. Always obey the instructions that you find on the packaging of the detergent products. 10.5 Liquid or powder detergent Compartment for prewash phase, soak programme or stain remover. 1 A 2 1. 21 2. B 4. 3. • Position A for powder detergent (factory setting).
www.aeg.com 10.6 Starting a programme without the delay start Touch button Start/Pause to start the programme. The relevant indicator stops to flash and stays on with red colour. The programme starts, the door is locked. The display show the indicator . The drain pump can operate for a short time when the appliance fills water. 10.
ENGLISH The door lock symbol in the display goes off. 2. Open the appliance door. 3. Close the appliance door and touch button Start/Pause. The programme or the delay start continues 10.13 Draining water out after end of cycle The washing programme is completed, but there is water in the drum: • The drum turns regularly to prevent the creases in the laundry. • The door stays locked. • You must drain the water to open the door: 1. If necessary, decrease the spin speed. 2. Touch the Start/Pause button.
www.aeg.com 12.1 Preparation to drying 1. Press button Ein/Aus for some seconds to activate the appliance 2. Load the laundry one item at a time. 3. Turn the programme dial to the drying programme applicable for the items to dry. The text bar in the display tells which programme you have chosen. When drying a big amount of laundry, to have good drying performances, make sure that the laundry itself is not rolled up and that is uniformly distributed in the drum.
ENGLISH 25 After some minutes from the end of the programme, the energy saving function automatically deactivates the appliance. 1. Remove the laundry from the appliance. 2. Make sure that the drum is empty. 13. DAILY USE - WASHING & DRYING WARNING! Refer to Safety chapters. 13.1 NON-STOP programme You can wash and dry your laundry setting a «non stop-programme». Proceed as follows: 1. Press button Ein/Aus for some seconds to activate the appliance . 2. Load the laundry one item at a time. 3.
www.aeg.com 13.4 At the end of the programme The appliance stops automatically. The acoustic signals operate (if they are active). For more information see ‘At the end of the drying programme “ of the previous chapter. 13.5 Fluff in the fabrics During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could release fluff. The released fluff could stick to the fabrics during the next cycle. This inconvenient increases with technical fabrics.
ENGLISH • • • • • programmes (60 °C max) for all types of fabric, or special for woollens only. Do not mix different types of detergents. To help the environment, do not use more than the correct quantity of detergent. Obey the instructions that you find on the on packaging of these products. Use the correct products for the type and colour of the fabric, the programme temperature and the level of soil.
www.aeg.com 14.11 General Tips Refer to the «Drying programmes» table to find the average drying times. The experience will help you to dry the laundry in a more correct way. Take note of the duration drying time of the cycles done before. When the drying programme is completed remove the laundry in a short time. To avoid the static charge at the end of the drying cycle: 1. Use fabric conditioner in the washing cycle. 2. Use special fabric conditioner for tumble dryers. 15.
ENGLISH 15.5 Cleaning the detergent dispenser 1. 2. 1 2 3. 4. 15.6 Cleaning the air filters The air filters collect the fluff. The fluff normally occurs when the clothes are dried in a washer-dryer. • At the end of each drying cycle in the display the indicator the primary air filter. The text bar says to clean the primary filter (see pict. 1-5). is on to tell you to clean may flash to remind you that both air filters should be • Occasionally the indicator cleaned.
www.aeg.com L L PU PU 3. LL 4. U P L L 5. 6. 7. 8. + 9. 10. To have best drying performances clean regularly the air filters with warm water and afterwards dry them with a towel. Clogged filter increases the drying time. WARNING! The primary filter recess must not be blocked by any object. If you only wash the laundry with your washer-dryer, it is normal to find some humidity in the primary air filter.
ENGLISH 15.7 Cleaning the drain filter WARNING! Do not clean the drain filter if the water in the appliance is hot. 1. 2. 2 1 1 2 1 3. 4. 1 5. 6.
www.aeg.com 7. 8. 1 2 9. 2 1 15.8 Cleaning the inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. • The indicator of button Start/Pause flashes and the display shows the related alarm. Refer to 'Troubleshooting'. To clean the water inlet filters: • Close the water tap. • Remove the water inlet hose from the water tap.
ENGLISH 33 • Remove the inlet hose behind the appliance. • Clean the filter in the valve with a stiff brush or a towel. • Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. • Open the water tap. 45° 20° 15.9 Emergency drain 15.10 Frost precautions Because of a malfunction, the appliance cannot drain the water. If the appliance is installed in an area where the temperature can be less than 0° C, remove the remaining water from the inlet hose and the drain pump.
www.aeg.com WARNING! Make sure that the temperature is more than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. 16. TROUBLESHOOTING WARNING! Refer to Safety chapters. 16.1 Introduction The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the Authorised Service Centre.
ENGLISH Message 35 Possible solution Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'. Make sure that the connection of the drain hose is correct. The display tells to check the Make sure that the appliance door is not open or closed door. correctly. The display tells there is a water alert. The anti-flood device is activated: • Disconnect the appliance. • Close the water tap. • Contact the service centre.
www.aeg.com Problem Possible solution The appliance fills with water Make sure that the drain hose is in the correct position. and drains immediately. The hose may be too low. The spin phase does not operate or the washing cycle lasts longer than usually. Make sure that the spin phase is not off. Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'. Make sure that the this is not a balance problem.
ENGLISH 37 Problem Possible solution The washing cycle is longer than the time displayed. An unbalanced laundry load increases the duration time. This is a normal behaviour of the appliance. After a steam programme, garments are partially wet. Make sure that the appliance is accurately levelled. Adjust the appliance by raising or lowering the feet. After a steam programme, garments are not sufficiently smooth. Make sure that you set a correct STEAM programme.
www.aeg.com Make sure that the water level inside the drum is not too high. Proceed with an emergency drain, if necessary (refer to «Emergency drain» in «Care and cleaning» chapter). To open the door, proceed as follows: 1. Press the button Ein/Aus to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Keep the emergency unlock trigger pulled downward and, at the same time, open the appliance door. 5.
ENGLISH 39 • Remove the cardboard top. • Remove the polystyrene packaging materials. • Remove the internal film. • Open the door. • Remove the polystyrene piece from the door seal and all the items from the drum. • Put one of the polystyrene packaging elements on the floor behind the appliance. • Carefully put down the appliance with the rear side on it. • Make sure not to damage the hoses. • Remove the polystyrene protection from the bottom.
www.aeg.com • Pull up the appliance in vertical position. • Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliances in factory. • Remove the three bolts. • Use the key supplied with the appliance. • Pull out the plastic spacers. • Put the plastic caps in the holes. • You can find these caps in the user manual bag.
ENGLISH 41 17.3 Installation under a counter The appliance can be installed as freestanding or below the kitchen counter with correct space (see picture). 600 mm ≥ 870 mm CAUTION! To assure free air circulation under the appliance, do not attach the sound barriers (if available). 600 mm 17.4 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
www.aeg.com 17.5 The inlet hose • Connect the hose to the back appliance. Turn the inlet hose only left or right. • Loose the ring nut to set it in the correct position. 45 20 O O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. 17.
ENGLISH 43 • Making an U form with the drain hose. On the edge of a sink • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. To a stand pipe with vent-hole • Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). Refer to the illustration. • The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm - min. 1.
www.aeg.com To a sink spigot • Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. • Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. To a wall-pipe • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 18.
ENGLISH Spin Speed Wool 1 Maximum 1600 rpm 45 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 19. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances * marked with the symbol with the household waste.
www.aeg.
ENGLISH 47
132907970-A-312014 www.aeg.
