L 99695 HWD USER MANUAL EN User Manual Washer Dryer
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................6 3. PRODUCT DESCRIPTION...........................................................................................7 4. CONTROL PANEL....................................................................................................... 9 5. PROGRAMMES...
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • • The appliance shall be installed as a freestanding product or below the kitchen worktop if space margins permit. Do not install the appliance behind a lockable door, a sliding door or a door with a hinge on the opposite side, that would prevent the appliance door from being fully open. Connect the mains plug to the mains socket only at the end of the installation process. Make sure that the mains plug is accessible after installation.
ENGLISH • • • • • • • • • • • • 5 Do not run the appliance without filters. Clean the lint filter before or after each use. Items that have been soiled with substances such as vegetable or mineral oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed separately with an extra amount of detergent before being dried in the washer dryer. Do not use the appliance if items have been soiled with industrial chemicals.
www.aeg.com 2. SAFETY INSTRUCTIONS 2.1 Installation The installation must comply with relevant national regulations. • Follow the installation instructions supplied with the appliance. • Do not install or use the appliance where the temperature can be less than 5°C or higher than 35 °C. • Always keep the appliance vertical when being moved. • To make sure the compressor works properly, wait 6 hours after the installation before using the appliance.
ENGLISH chlorohydrocarbons. This system must stay tight. The damage of the system can cause a leakage. – Do not use a detergent ball if setting a non-stop programme. WARNING! Risk of injury or damage to the appliance. 2.6 Disposal • Do not sit or stand on the open door. • Do not dry dripping wet clothes in the appliance. 2.5 Compressor WARNING! Risk of damage to the appliance.
www.aeg.com 3.2 How to activate the child safety device To close the door, turn the device anticlockwise until the groove is vertical. This device prevents children or pets from being closed in the drum. Turn the device clockwise, until the groove is horizontal. You cannot close the door. 3.3 Accessories 1 4 2 3 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts.
ENGLISH 9 4. CONTROL PANEL 4.1 Control panel description 1 2 3 SPECIAAL/ SPECIAL WA S S E N / D R O G E N L AVA G E / S E C H A G E Fijne Was Katoen Délicats Blanc/Couleurs Strijkvrij Katoen Eco Repassage Facile Synthetica Wol/Zijde Tijdgestuurd 5 6 Minuterie Laine/Soie Anti-Allergie Spoelen Rinçage Anti-Allergies Centrif.
www.aeg.com The display shows: A The text bar: • Guides you in the use of the appliance. • Shows the programme status and phase. • Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. Child safety lock B Door locked You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off. If the programme is completed but the symbol stays on: • The «Rinse hold» function is on.
ENGLISH 11 This part comes on only if the door is open - Refer to 'Activating the appliance and setting a programme'. E Maximum allowed load of laundry for the set programme (in kg). Graphic bars To set a function: The function indicator comes on when the related function is set. The empty indicator bar appears only if the related function is available for the set programme. If an indicator bar does not come on, it means that it is not available. The indicator bar fills accordingly to the set functions.
www.aeg.com Spin speed of the set programme No Spin indicator1) J Rinse Hold indicator 1) Only available for SPIN/DRAIN programme. Default temperature of the set programme K Cold water 5. PROGRAMMES 5.
ENGLISH Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) 6 kg Drying programme for cotton items. 4 kg Drying programme for synthetic items. 1 kg Drying programme for woollens. 13 Katoen - Coton Synthetica - Synthétiques Wol - Laine Washing programmes 4 kg 1200 rpm Delicate fabrics such as acrylics, viscose and mixed fabrics requiring gentler washing. Normal soil. 4 kg 800 rpm Synthetic items requiring a gentle wash.
www.aeg.com Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Steam programmes6) Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry softer. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam programmes do not perform any hygienic cycle.
ENGLISH 15 Tijd Besparen - Gain de ■ ■ ■ ■ Katoen Eco - Coton Eco ■ ■ ■ ■ Synthetica - Synthétiques ■ ■ ■ ■ Wol/Zijde - Laine/ Soie ■ ■ Anti-Allergie - AntiAllergies ■ ■ ■ ■ ■ Fijne Was - Délicats ■ ■ ■ ■ ■ ■ ■ Strijkvrij - Repassage Facile ■ ■ ■ ■ ■ ■ ■ Super Eco ■ ■ 20 Min. - 3 kg ■ Spoelen - Rinçage ■ Centrif./Pompen Essorage/Vidange ■ ■ Temps2) Soak ■ çage+1) Stains Katoen - Blanc/ Couleurs T.
www.aeg.
ENGLISH 5.4 Woolmark Apparel Care Blue • The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of wool garments labelled as "hand wash" provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M1230 • The wool drying cycle of this machine has been tested and approved by The Woolmark Company.
www.aeg.com Programmes Load (kg) Cottons 40°C 9 1.05 71 180 Synthetics 40°C 4 0.88 60 142 Delicates 40°C 4 0.70 63 91 1.5 0.35 59 58 Wool/Handwash 30°C Energy Water conApproximate proconsump- sumption (li- gramme duration tion (kWh) tre) (minutes) 1) «Cotton Energy Saving programme » at 60°C with a load of 9kg is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards. 7. SETTINGS 7.
ENGLISH • You do not use the appliance for 5 minutes before you press the Start/ Pauze - Départ/Pause button. All settings are cancelled. Press the Aan/Uit - Marche/Arrêt button to activate the appliance again. Set the washing programme and all possible functions again. • 5 minutes after the end of the washing programme. Refer to "AUTO Stand-by option". 8.3 Programme knob 19 The duration of the steam phase changes accordingly to your selection. 8.
www.aeg.com function, put the stain remover into compartment . The programme duration increases. This function is not available with a temperature lower than 40° C. 8.12 T./min Touch button T./min to: • Decrease the maximum speed of the spin phase of the programme. • Deactivate the spin phase ( 'No spin' function). • Activate the Rinse Hold function. Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed. 8.13 Temp.
ENGLISH 21 10. DAILY USE - WASHING ONLY WARNING! Refer to Safety chapters. 10.1 Before activating the appliance 1. Connect the mains plug to the mains socket. 2. Open the water tap. 10.2 Activating the appliance and setting a programme 1. Press button Aan/Uit - Marche/Arrêt to activate the appliance. 2. Turn the programme knob to the required programme. The programme indicator comes on. The indicator of Start/Pauze - Départ/ Pause button flashes with red colour.
www.aeg.com Always obey the instructions that you find on the packaging of the detergent products. 4. 10.5 Liquid or powder detergent 1. 1 Close the detergent dispenser. When you use the liquid detergent: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid then the maximum level. • Do not set the prewash phase. • Do not set the delay start. 2 Open the detergent dispenser. 2. A 10.
ENGLISH 10.7 Cycle time recalculation After approximately 15 minutes from the start of the programme: • The appliance adjusts automatically the cycle time to the laundry you have put in the drum to have perfect washing results in the minimum necessary time. • The display shows the new time value. 10.8 Starting a programme with the delay start 1. Touch button Startuitstel - Départ Différé again and again to set the desired delayed start. The display show the expected end of the programme. 2.
www.aeg.com • You must drain the water to open the door: 1. If necessary, decrease the spin speed. 2. Touch the Start/Pauze - Départ/ Pause button. The appliance drains the water and spins. 3. When the programme is completed and the door lock indicator goes off, you can open the door. 4. Press Aan/Uit - Marche/Arrêt some seconds to deactivate the appliance. The appliance drains and spins automatically after approximately18 hours.
ENGLISH At the beginning of the drying cycle (3 – 5 min.) there could be a slightly higher sound level. This is the compressor start and it is quite normal for compressor powered appliances such refrigerators, freezers and so on. 11.2 Automatic drying 1. Touch button Automatisch Automatique repeatedly to set the required dryness level. The indicators on the control panel illuminate accordingly: a. IRON DRY level - 1 indicator on: for cotton items b.
www.aeg.com 12.1 NON-STOP programme You can wash and dry your laundry setting a «non stop-programme». Proceed as follows: 1. Press button Aan/Uit - Marche/Arrêt for some seconds to activate the appliance . 2. Load the laundry one item at a time. 3. Put the detergent and the additives in the appropriate compartment. 4. Turn the programme dial to the washing programme. The display shows the default temperature and spin. If necessary, change them according to your laundry. 5. Set the available options.
ENGLISH To prevent the fluff in your laundry, we recommend that you: • To do not wash dark fabrics after you washed and dried light coloured fabrics (new sponge, hand towel, wool, sweatshirt ) and the contrary. • To dry this type of fabrics at open air when they are washed the first time. • To clean the drain filter. • After the drying phase, clean the air filters, the empty drum, the gasket and the door with a wet cloth. To remove the fluff inside the drum, set a special programme: 27 • Empty the drum.
www.aeg.com • Follow the instructions that you find on packaging of the detergents or other treatments without exceeding ). the indicated maximum level ( • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. • If your appliance has not the detergent dispenser with the flap device, add the liquid detergents with a dosing ball (supplied by the detergent's manufacturer). 13.
ENGLISH Experience will help you to dry the laundry better. Take note of the duration of the cycles done before. To avoid the static charge at the end of the drying cycle: 1. Use fabric conditioner in the washing cycle. 2. Use special fabric conditioner for tumble dryers. 3. Do not pour any detergent or softener before a drying cycle. 29 4. Do not dry rough and smooth textiles together, to avoid scorching on smooth garments. 5. Remove all objects from garment pockets, especially melting objects.
www.aeg.com 14.5 Cleaning the detergent dispenser 1. 2. 1 2 3. 4. 14.6 Cleaning the air filters The air filters collect the fluff. The fluff normally occurs when the clothes are dried in a washer-dryer. • At the end of each drying cycle in the display the indicator is on to advise to clean the primary air filter. The text bar suggests to clean the primary filter (see pictures from 1 to 5). • Occasionally the indicator may flash to remind you that both air filters should be cleaned.
ENGLISH L L PU PU 3. LL 4. U P L L 5. 6. 7. 8. + 9. 10. To have best drying performances clean regularly the air filters with warm water and afterwards dry them with a towel. Clogged air filter increases the drying time and the energy consumption! WARNING! The primary filter recess must not be blocked by any object. If you only wash the laundry with your washer-dryer, it is normal to find some humidity in the primary air filter.
www.aeg.com 14.7 Cleaning the drain filter WARNING! Do not clean the drain filter if the water in the appliance is hot. WARNING! Each time you carry out the special programme CLE to remove fluff, clean the drain filter afterwards. 1. 2. 2 1 1 2 1 3. 4. 1 5. 6.
ENGLISH 7. 33 8. 1 2 9. 2 1 14.8 Cleaning the inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. • The indicator of button Start/Pauze - Départ/Pause flashes and the display shows the related alarm. Refer to 'Troubleshooting'. To clean the water inlet filters: • Close the water tap. • Remove the water inlet hose from the water tap.
www.aeg.com • Remove the inlet hose behind the appliance. • Clean the filter in the valve with a stiff brush or a towel. • Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. • Open the water tap. 45° 20° 14.9 Emergency drain 14.10 Frost precautions Because of a malfunction, the appliance cannot drain the water.
ENGLISH 35 WARNING! Make sure that the temperature is more than 5 °C and the water is flowing from the tap before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. 15. TROUBLESHOOTING WARNING! Refer to Safety chapters. 15.1 Introduction The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the Authorised Service Centre.
www.aeg.com Message Possible solution Make sure that the connection of the drain hose is correct. The display tells to check the Make sure that the appliance door is not open or closed door. correctly. The display tells there is a water alert. The anti-flood device is activated: • Disconnect the appliance. • Close the water tap. • Contact the service centre. The display tells that the main supply is unstable. Wait until the mains supply is stable. The appliance automatically starts operating.
ENGLISH Problem Possible solution The spin phase does not operate or the washing cycle lasts longer than usually. Make sure that the spin phase is not off. 37 Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'. Make sure that the this is not a balance problem. Adjust manually the items in the drum and start the spin phase again. There is water on the floor.
www.aeg.com Problem Possible solution The washing cycle is shorter than the time displayed. The appliance calculates a new time according to the laundry load. The washing cycle is longer than the time displayed. An unbalanced laundry load increases the duration time. This is a normal behaviour of the appliance. After a steam programme, garments are partially wet. Make sure that the appliance is accurately levelled. Adjust the appliance by raising or lowering the feet.
ENGLISH 39 Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain (refer to «Emergency drain» in «Care and cleaning» chapter). To open the door, proceed as follows: 1. Press the Aan/Uit - Marche/Arrêt button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Keep the emergency unlock trigger pulled downward and, at the same time, open the appliance door. 5.
www.aeg.com • Remove the cardboard top. • Remove the polystyrene packaging materials. • Remove the internal film. • Open the door. • Remove the polystyrene piece from the door seal and all the items from the drum. • Put one of the polystyrene packaging elements on the floor behind the appliance. • Carefully put down the appliance with the rear side on it. • Make sure not to damage the hoses. • Remove the polystyrene protection from the bottom.
ENGLISH 41 • Pull up the appliance in vertical position. • Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliances in factory. • Remove the three bolts. • Use the key supplied with the appliance. • Pull out the plastic spacers. • Put the plastic caps in the holes. • You can find these caps in the user manual bag.
www.aeg.com 16.3 Installation under a counter The appliance can be installed as freestanding or below the kitchen counter with correct space (see picture). 600 mm ≥ 870 mm CAUTION! Do not install the appliance inside a sealed hollow! Make sure that there is air circulation throw the bottom of the furniture. 600 mm CAUTION! To assure free air circulation under the appliance, do not attach the sound barriers (if available). 16.
ENGLISH 43 16.5 The inlet hose • Connect the hose to the back appliance. Turn the inlet hose only left or right. • Loose the ring nut to set it in the correct position. 45 20 O O • Connect the water inlet hose to the cold water tap with 3/4" thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. 16.6 Water-stop device The inlet hose has a water stop device.
www.aeg.com • Make a U shape with the drain hose. On the edge of a sink • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. To a stand pipe with vent-hole • Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). Refer to the illustration. • The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm - min. 1.
ENGLISH 45 To a sink spigot • Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. • Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink. To a wall-pipe • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 17.
www.aeg.com Spin Speed Wool 1 kg Maximum 1600 rpm This product contains HFC - R134a/GWP1430 0.12 kg fluorinated gas hermetically sealed. 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 18. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances.
ENGLISH 47
132906066-A-432017 www.aeg.