EN User Manual Washer Dryer L 99695 HWD
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 5 3. PRODUCT DESCRIPTION.............................................................................................. 7 4. CONTROL PANEL...........................................................................................................8 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • • side, where the appliance door can not be fully opened. Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. Ensure you have good ventilation in the installation room to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.
ENGLISH • • • • • • • • 5 Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the wash dryer. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. Remove all objects from pockets such as lighters and matches.
www.aeg.com 2.2 Electrical Connection WARNING! Risk of fire and electrical shock. • The appliance must be earthed. • Always use a correctly installed shockproof socket. • Do not use multi-plug adapters and extension cables. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • Do not touch the mains cable or the mains plug with wet hands. • Only for UK and Ireland: The appliance has a 13 amp mains plug.
ENGLISH 3. PRODUCT DESCRIPTION 3.1 Appliance overview 1 2 3 10 4 11 12 5 6 13 7 9 8 1 2 3 4 5 6 7 8 Worktop Detergent dispenser Air filter(s) Control panel Door handle Rating plate Drain pump filter Feet for the appliance level 3.2 How to activate the child safety device This device prevents children or pets to be closed in the drum. Turn the device clockwise, until the groove is horizontal. You cannot close the door.
www.aeg.com 3.3 Accessories 1 2 4 3 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink. 4. CONTROL PANEL 4.
ENGLISH 4.2 Display A K J B I H G C F D E The display shows: A The text bar: • Guides you in the use of the appliance. • Shows the programme status and phase. • Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child safety lock Door locked C You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off.
www.aeg.com Digit area Time of the day When you activate the appliance the display shows the time of the day for some seconds. To adjust the clock, refer to "Clock setting". Programme duration When you set the programme, the cycle duration is displayed for a few seconds then, the time of the programme end appears again. Programme duration indicator The indicator comes on when the digits shows the programme duration.
ENGLISH Time save The indicator comes on when you set one of the programme duration. F Shortened time Extra Quick G Indicator for air filters Extra rinsing H The value shows the total number of the rinses. The indicator bar fills accordingly the numbers of rinses. Stain indicator Prewash indicator I Soak indicator The indicator bar fills accordingly to the set functions. Spin speed of the set programme J No Spin indicator1) Rinse Hold indicator 1) Only available for SPIN/DRAIN programme.
www.aeg.com 5. PROGRAMMES 5.1 Programme Chart Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Washing/Drying programmes1) Katoen - Blanc/ Couleurs 95°C - Cold 9 kg 1600 rpm 9 kg Katoen Eco - Co- 1600 rpm ton Eco2) 60°C - 40°C Synthetica - Synthétiques 60°C - Cold Wol/Zijde Laine/Soie 40°C - Cold Anti-Allergie Anti-Allergies 60°C White cotton and coloured cotton. Normal soil and light soil. White cotton and colour-fast cotton.
ENGLISH Programme Temperature range 13 Maximum load Maximum spin speed Programme description (Type of load and soil level) 4 kg 1200 rpm Delicate fabrics as acrylics, viscose, polyester items. Normal soil. 4 kg 800 rpm Synthetic items to be gentle washed. Normal and Super Eco Cold 3 kg 1200 rpm Mixed fabric (cotton and synthetic items).5) 20 Min. - 3 kg 40°C - 30°C 3 kg 1200 rpm Cottons and synthetics items with light soil level or worn only once. To rinse and spin the laundry. All fabrics.
www.aeg.com Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) up to 1.5 kg Steam programme for cotton and synthetic items. This cycle removes odours from the laundry.9) Opfrissen - Rafraîchir 40°C 1) When you set a Washing / Drying programme, the display tells you that the drying cycle is not set. If you want to dry your laundry, set an automatic drying or a timed drying.
ENGLISH 15 Tijd Besparen - Gain de Temps2) Startuitstel - Départ Différé ■ 3) ■ ■ ■ ■ ■ ■ ■ ■ Synthetica - Synthétiques ■ ■ ■ ■ ■ ■ Anti-Allergie - AntiAllergies ■ ■ ■ ■ ■ Fijne Was - Délicats ■ ■ ■ ■ ■ ■ ■ Strijkvrij - Repassage Facile ■ ■ ■ ■ ■ ■ ■ Super Eco ■ ■ 20 Min. - 3 kg ■ Spoelen - Rinçage ■ Centrif./Pompen Essorage/Vidange ■ Wol/Zijde - Laine/ Soie Soak Katoen Eco - Coton Eco T.
www.aeg.
ENGLISH 5.4 Woolmark Apparel Care Blue • The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of wool garments labelled as «hand wash» provided that the garments are 17 washed according to the instructions issued by the manufacturer of this washing machine. Follow the garment care label for drying and other laundry instructions.
www.aeg.com Programmes Load (kg) Wool/Handwash 30 °C Energy Water conApproximate proconsump- sumption (li- gramme duration tion (kWh) tre) (minutes) 1.5 0.35 59 58 1) «Cotton Energy Saving programme » at 60°C with a load of 9 kg is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards. 7. SETTINGS 7.1 Acoustic signals You can hear the acoustic signals when: • You activate the appliance. • You deactivate the appliance. • You touch the buttons.
ENGLISH 8.3 Programme knob Turn this knob to set a programme. The related programme indicator comes on. 8.4 Automatisch Automatique Touch this button to set one of 3 automatic dryness levels proposed by the appliance. On the control panel the dryness indicators illuminate accordingly. 8.9 Tijd Besparen - Gain de Temps Touch button Tijd Besparen - Gain de Temps to decrease the programme time. You can select: • SHORTENED DURATION: to wash items with daily soil.
www.aeg.com The display shows only the spin speeds available for the set programme. • Deactivate the spin phase ( 'No spin' function). • Activate the Rinse Hold function. Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed. 8.13 Temp.°C Touch this button to change the default temperature. Symbols and = cold water 9. BEFORE FIRST USE 1. Put a small quantity of detergent in the compartment for washing phase. 2.
ENGLISH The programme indicator comes on. The indicator of Start/Pauze - Départ/ Pause button flashes with red colour. The display shows the default temperature and spin and, if the door is already open, the maximum load allowed for the set programme (this information disappears when you close the door). 3. If necessary, touch Temp.°C button and T./min button to change the water temperature and the spin speed. 4. If necessary, touch the other buttons to add some options or to set a delayed start.
www.aeg.com 10.5 Liquid or powder detergent Maximum level for quantity of liquid additives. Flap for powder or liquid detergent. Always obey the instructions that you find on the packaging of the detergent products. 1 A 2 1. 2. B 4. 3. • Position A for powder detergent (factory setting). • Position B for liquid detergent. When you use the liquid detergent: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid then the maximum level. • Do not set the prewash phase.
ENGLISH 10.7 Behaviour of the appliance After approximately 15 minutes from the start of the programme: • The appliance adjusts automatically the cycle time to the laundry you have put in the drum to have perfect washing results in the minimum necessary time. • The display shows the new time value. 10.8 Starting a programme with the delay start 1. Touch button Startuitstel - Départ Différé again and again to set the desired delayed start. The display show the expected end of the programme. 2.
www.aeg.com • The drum turns regularly to prevent the creases in the laundry. • The door stays locked. • You must drain the water to open the door: 10.14 AUTO Stand-by option 1. If necessary, decrease the spin speed. 2. Touch the Start/Pauze - Départ/ Pause button. The appliance drains the water and spins. 3. When the programme is completed and the door lock indicator goes off, you can open the door. 4. Press Aan/Uit - Marche/Arrêt some seconds to deactivate the appliance.
ENGLISH At the beginning of the drying cycle (3 – 5 min.) there could be a slightly higher sound level. This is the compressor start and it is quite normal for compressor powered appliances such refrigerators, freezers and so on. 12.2 Automatic drying 1. Touch button Automatisch Automatique repeatedly to set the required dryness level. The indicators on the control panel illuminate accordingly: a. IRON DRY level - 1 indicator on: for cotton items b.
www.aeg.com 13.1 NON-STOP programme You can wash and dry your laundry setting a «non stop-programme». Proceed as follows: 1. Press button Aan/Uit - Marche/Arrêt for some seconds to activate the appliance . 2. Load the laundry one item at a time. 3. Put the detergent and the additives in the appropriate compartment. 4. Turn the programme dial to the washing programme. The display shows the default temperature and spin. If necessary, change them according to your laundry. 5. Set the available options.
ENGLISH • To dry this type of fabrics at open air when they are washed the first time. • To clean the drain filter. • After the drying phase, clean the air filters, the empty drum, the gasket and the door with a wet cloth. To remove the fluff inside the drum, set a special programme: • Empty the drum. 27 • Clean the drum, the gasket and the door with a wet cloth. • Set the rinse programme. • Touch at the same time T.
www.aeg.com • Always start a washing programme with the maximum load of laundry. • If necessary, use a stain remover when you set a programme with a low temperature. • To use the correct quantity of the detergent, check the water hardness of your domestic system 14.5 Water hardness If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener. 14.
ENGLISH 29 15. CARE AND CLEANING 15.3 Maintenance wash WARNING! Refer to Safety chapters. With the low temperature programmes it is possible that some detergent stays in the drum. Make regularly a maintenance wash. To do this: 15.1 External cleaning Clean the appliance only with soap and warm water. Fully dry all the surfaces. • Remove the laundry from the drum. • Set the cotton programme with the highest temperature with a small quantity of detergent.
www.aeg.com 3. 4. 15.6 Cleaning the air filters The air filters collect the fluff. The fluff normally occurs when the clothes are dried in a washer-dryer. • At the end of each drying cycle in the display the indicator the primary air filter. The text bar says to clean the primary filter (see pict. 1-5). is on to tell you to clean may flash to remind you that both air filters should be • Occasionally the indicator cleaned.
ENGLISH U P L L 5. 6. 7. 8. + 10. 9. To have best drying performances clean regularly the air filters with warm water and afterwards dry them with a towel. Clogged filter increases the drying time. WARNING! The primary filter recess must not be blocked by any object. If you only wash the laundry with your washer-dryer, it is normal to find some humidity in the primary air filter. 15.7 Cleaning the drain filter WARNING! Do not clean the drain filter if the water in the appliance is hot.
www.aeg.com 1. 2. 2 1 1 2 1 3. 4. 1 5. 6. 1 7. 2 2 8.
ENGLISH 33 9. 2 1 15.8 Cleaning the inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. • The indicator of button Start/Pauze - Départ/Pause flashes and the display shows the related alarm. Refer to 'Troubleshooting'. To clean the water inlet filters: • Close the water tap. • Remove the water inlet hose from the water tap.
www.aeg.com • Clean the filter in the valve with a stiff brush or a towel. • Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. • Open the water tap. 45° 20° 15.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (9) of 'Cleaning the drain filter'. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate again the drain system: 1.
ENGLISH 35 16.1 Introduction The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the Authorised Service Centre. With some problems, the acoustic signals operate and the display shows an alarm message: CAUTION! Deactivate the appliance before you do the checks. 16.
www.aeg.com Message Possible solution At the end of the washing cycle the display tells that too much detergent was used. This is not a failure but a suggestion for next wash to decrease the detergent quantity. The display tells to check the Make sure that the filter drawer is correctly inserted. air filter (the indicator flashes and the acoustic signal operates) Problems without alarm messages Problem Possible solution The programme does not start.
ENGLISH Problem 37 Possible solution Make sure that the drain hose have no damages. Make sure you use the correct detergent and the correct quantity of it. You cannot open the appliance door. Make sure that the washing programme is finished. Set the drain or the spin programme if there is water in the drum. Make sure that the appliance receives electrical power. This problem may be caused by a failure of the appliance. Contact the Authorised Service Centre.
www.aeg.com Problem Possible solution Make sure you have set the correct cycle. If necessary, set a short drying time again. The drying cycle is too long. Make sure the air filters are properly cleaned. Make sure your laundry load does not exceed the declared load for the set programme. Make sure that the room temperature is in the correct range. The laundry is full of different colours fluff. Set a drying cycle to remove some fluff (for more details refer to 'FLUFF IN THE FABRICS' ).
ENGLISH 39 5. Take out the laundry and then close the appliance door. 6. Close the filter flap. 17. INSTALLATION WARNING! Refer to Safety chapters. 17.1 Unpacking WARNING! As you will put down the appliance on the rear side, wait about 6 hours before you use it. This time is necessary to enable the compressor to work properly. WARNING! Remove all the packaging and the transit bolts before installing the appliance. Use the gloves. • Remove the external film.
www.aeg.com • Remove the internal film. • Open the door. • Remove the polystyrene piece from the door seal and all the items from the drum. • Put one of the polystyrene packaging elements on the floor behind the appliance. • Carefully put down the appliance with the rear side on it. • Make sure not to damage the hoses. • Remove the polystyrene protection from the bottom.
ENGLISH 41 • Pull up the appliance in vertical position. • Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliances in factory. • Remove the three bolts. • Use the key supplied with the appliance. • Pull out the plastic spacers. • Put the plastic caps in the holes. • You can find these caps in the user manual bag.
www.aeg.com 17.3 Installation under a counter The appliance can be installed as freestanding or below the kitchen counter with correct space (see picture). 600 mm ≥ 870 mm CAUTION! To assure free air circulation under the appliance, do not attach the sound barriers (if available). 600 mm 17.4 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
ENGLISH 43 17.5 The inlet hose • Connect the hose to the back appliance. Turn the inlet hose only left or right. • Loose the ring nut to set it in the correct position. 45 20 O O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. 17.6 Water-stop device The inlet hose has a water stop device.
www.aeg.com • Making an U form with the drain hose. On the edge of a sink • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. To a stand pipe with vent-hole • Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). Refer to the illustration. • The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm - min. 1.
ENGLISH 45 To a sink spigot • Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. • Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. To a wall-pipe • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 18.
www.aeg.com Spin Speed Wool 1 Maximum 1600 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 19. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances * marked with the symbol with the household waste.
ENGLISH 47
132906062-A-472014 www.aeg.