EN User Manual Washer Dryer L 99695 HWD
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................5 3. PRODUCT DESCRIPTION...........................................................................................7 4. CONTROL PANEL....................................................................................................... 8 5. PROGRAMMES ..
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • • side, where the appliance door can not be fully opened. Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. Ensure you have good ventilation in the installation room to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.
ENGLISH • • • • • • • • 5 Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the wash dryer. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. Remove all objects from pockets such as lighters and matches.
www.aeg.com 2.2 Electrical Connection WARNING! Risk of fire and electrical shock. • The appliance must be earthed. • Always use a correctly installed shockproof socket. • Do not use multi-plug adapters and extension cables. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • Do not touch the mains cable or the mains plug with wet hands. • Only for UK and Ireland: The appliance has a 13 amp mains plug.
ENGLISH 3. PRODUCT DESCRIPTION 3.1 Appliance overview 1 2 3 10 4 11 12 5 6 13 7 9 8 1 2 3 4 5 6 7 8 Worktop Detergent dispenser Air filter(s) Control panel Door handle Rating plate Drain pump filter Feet for the appliance level 3.2 How to activate the child safety device This device prevents children or pets to be closed in the drum. Turn the device clockwise, until the groove is horizontal. You cannot close the door.
www.aeg.com 3.3 Accessories 1 2 4 3 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Inlet Hose To connect the appliance to the water tap. 4 Plastic hose guide To connect the drain hose on the edge of a sink. 4. CONTROL PANEL 4.
ENGLISH 4.2 Display A K J B I H G C F D E The display shows: A The text bar: • Guides you in the use of the appliance. • Shows the programme status and phase. • Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child safety lock Door locked C You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off.
www.aeg.com Digit area Time of the day When you activate the appliance the display shows the time of the day for some seconds. To adjust the clock, refer to "Clock setting". Programme duration When you set the programme, the cycle duration is displayed for a few seconds then, the time of the programme end appears again. Programme duration indicator The indicator comes on when the digits shows the programme duration.
ENGLISH Time save The indicator comes on when you set one of the programme duration. F Shortened time Extra Quick G Indicator for air filters Extra rinsing H The value shows the total number of the rinses. The indicator bar fills accordingly the numbers of rinses. Stain indicator Prewash indicator I Soak indicator The indicator bar fills accordingly to the set functions. Spin speed of the set programme J No Spin indicator1) Rinse Hold indicator 1) Only available for SPIN/DRAIN programme.
www.aeg.com 5. PROGRAMMES 5.1 Programme Chart Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Washing/Drying programmes1) Cottons 95°C - Cold Cottons Eco2) 60°C - 40°C Synthetics 60°C - Cold Wool/Silk 40°C - Cold Anti-Allergy 60°C 9 kg 1600 rpm White cotton and coloured cotton. Normal soil and light soil. 9 kg 1600 rpm White cotton and colour-fast cotton. Normal soil.
ENGLISH 13 Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Super Eco Cold 3 kg 1200 rpm Mixed fabric (cotton and synthetic items).5) 20 Min. - 3 Kg 40°C - 30°C 3 kg 1200 rpm Cottons and synthetics items with light soil level or worn only once. 9 kg 1600 rpm All fabrics. To rinse and spin the laundry. Make sure the spin speed agrees with the laundry. 9 kg 1600 rpm All fabrics. To spin the laundry and to drain the water in the drum.
www.aeg.com Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) up to 1.5 kg Steam programme for cotton and synthetic items. This cycle removes odours from the laundry.7) Refresh 40°C 1) When you set a Washing / Drying programme, the display tells you that the drying cycle is not set. If you want to dry your laundry, set an automatic drying or a timed drying.
ENGLISH 15 20 Min. - 3 Kg ■ Rinse ■ Spin/Drain ■ Delay Start Time Save2) Extra Rinse1) Soak Stains Spin Prewash Programme ■ ■ ■ ■ ■ ■ 1) If the Permanent Extra Rinse option is activated, the appliance adds some additional rinses. In the Rinse programme, if you set a low spin speed the appliance performs delicate rinses and a short spin. 2) If you set a shorter duration, we recommend that you decrease the quantity of the load.
www.aeg.
ENGLISH 17 At programme start the display shows the duration programme for the maximum load capacity. During the washing phase the programme duration is automatically calculated and can be greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton 60°C, maximum load capacity 9 kg, the programme duration exceeds 2 hours; real load 1 kg, the programme duration don’t reach 1 hour). When the appliance is calculating the real programme duration a dot blinks in the display.
www.aeg.com • To activate/deactivate this function touch Time Save and Delay Start at the same time until the display show the indicator off. comes on/goes 8. OPTIONS 8.1 Touch Screen Make sure the touch screen and buttons are always clean and dry. 8.2 On/Off Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated.
ENGLISH 19 8.10 Extra Rinse 8.12 Spin Touch this button to add rinsing phases to a programme. Touch button Spin to: • Decrease the maximum speed of the spin phase of the programme. Use this function for persons allergic to detergents and in areas where the water is soft. 8.11 Stains/Prewash Touch this button to set one of the following functions: • Prewash Use this function for heavy soil. The appliance adds a prewash phase to the main wash. The programme duration increases.
www.aeg.com 4. Turn the programme knob to change the minutes. 5. Touch Start/Pause button to confirm the selection. 9.3 Language setting The first time you activate the appliance, the display shows the default language and tells you to confirm it or change it: 1. Turn the programme knob to set the desired language. 2. When the display shows the necessary language touch Start/ Pause button to confirm the selection. 9.4 Change the language after the first activation 1.
ENGLISH 10.4 Filling the detergent and additives 2. A Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Flap for powder or liquid detergent. Always obey the instructions that you find on the packaging of the detergent products. 10.5 Liquid or powder detergent Position A: for powder detergent (factory setting). 3. B Rotate the flap downwards.
www.aeg.com When you use the liquid detergent: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid then the maximum level. • Do not set the prewash phase. • Do not set the delay start. 10.6 Starting a programme without the delay start Touch button Start/Pause to start the programme. The relevant indicator stops to flash and stays on with red colour. The programme starts, the door is locked. The display show the indicator .
ENGLISH 10.12 Opening the door WARNING! If the temperature and level of the water in the drum are too high and the drum still rotates you cannot open the door. While a programme or the delay start operates, the appliance door is locked. To open the appliance door: 1. Touch button Start/Pause. The door lock symbol in the display goes off. 2. Open the appliance door. 3. Close the appliance door and touch button Start/Pause. The programme or the delay start continues 10.
www.aeg.com 11. DAILY USE - DRYING ONLY WARNING! Refer to Safety chapters. 11.1 Preparation to drying 1. Press button On/Off for some seconds to activate the appliance 2. Load the laundry one item at a time. 3. Turn the programme dial to the drying programme applicable for the items to dry. The text bar in the display tells which programme you have chosen.
ENGLISH After some minutes from the end of the programme, the energy saving function automatically deactivates the appliance. 25 1. Remove the laundry from the appliance. 2. Make sure that the drum is empty. 12. DAILY USE - WASHING & DRYING WARNING! Refer to Safety chapters. 12.1 NON-STOP programme You can wash and dry your laundry setting a «non stop-programme». Proceed as follows: 1. Press button On/Off for some seconds to activate the appliance . 2. Load the laundry one item at a time. 3.
www.aeg.com 12.4 At the end of the programme The appliance stops automatically. The acoustic signals operate (if they are active). For more information see ‘At the end of the drying programme “ of the previous chapter. After drying phase, clean the air filters, the drum, the seal and the inside of the door with a wet cloth. 12.5 Fluff in the fabrics During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could release fluff.
ENGLISH 13.3 Detergents and additives • Only use detergents and additives specially made for washing machines: – powder detergents for all types of fabric, – powder detergents for delicate fabrics (40 °C max) and woollens, – liquid detergents, preferably for low temperature wash programmes (60 °C max) for all types of fabric, or special for woollens only (detergent flap rotated in position B in the main wash dispenser compartment). • Do not mix different types of detergents.
www.aeg.com • dryness level • type of laundry • weight of the load size 13.10 Additional drying If, at the end of the drying programme, the laundry is still damp, set a short drying cycle again. WARNING! To avoid creases of fabrics or shrinks of the clothing do not over dry the laundry. 13.11 General Tips Refer to the «Drying programmes» table to find the average drying times. The experience will help you to dry the laundry in a more correct way.
ENGLISH 14.5 Cleaning the detergent dispenser 1. 2. 1 2 3. 4. 14.6 Cleaning the air filters The air filters collect the fluff. The fluff normally occurs when the clothes are dried in a washer-dryer. • At the end of each drying cycle in the display the indicator is on to advise to clean the primary air filter. The text bar suggests to clean the primary filter (see pictures from 1 to 5). • Occasionally the indicator may flash to remind you that both air filters should be cleaned.
www.aeg.com L L PU PU 3. LL 4. U P L L 5. 6. 7. 8. + 9. 10. To have best drying performances clean regularly the air filters with warm water and afterwards dry them with a towel. Clogged air filter increases the drying time and the energy consumption! WARNING! The primary filter recess must not be blocked by any object. If you only wash the laundry with your washer-dryer, it is normal to find some humidity in the primary air filter.
ENGLISH 14.7 Cleaning the drain filter WARNING! Do not clean the drain filter if the water in the appliance is hot. WARNING! Each time you carry out the special programme CLE to remove fluff, clean the drain filter afterwards. 1. 2. 2 1 1 2 1 3. 4. 1 5. 6.
www.aeg.com 7. 8. 1 2 9. 2 1 14.8 Cleaning the inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. • The indicator of button Start/Pause flashes and the display shows the related alarm. Refer to 'Troubleshooting'. To clean the water inlet filters: • Close the water tap. • Remove the water inlet hose from the water tap.
ENGLISH 33 • Remove the inlet hose behind the appliance. • Clean the filter in the valve with a stiff brush or a towel. • Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. • Open the water tap. 45° 20° 14.9 Emergency drain 14.10 Frost precautions Because of a malfunction, the appliance cannot drain the water. If the appliance is installed in an area where the temperature can be less than 0° C, remove the remaining water from the inlet hose and the drain pump.
www.aeg.com WARNING! Make sure that the temperature is more than 5 °C and the water is flowing from the tap before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. 15. TROUBLESHOOTING WARNING! Refer to Safety chapters. 15.1 Introduction The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the Authorised Service Centre.
ENGLISH Message 35 Possible solution Make sure that the connection of the drain hose is correct. The display tells to check the Make sure that the appliance door is not open or closed door. correctly. The display tells there is a water alert. The anti-flood device is activated: • Disconnect the appliance. • Close the water tap. • Contact the service centre. The display tells that the main supply is unstable. Wait until the mains supply is stable. The appliance automatically starts operating.
www.aeg.com Problem Possible solution The spin phase does not operate or the washing cycle lasts longer than usually. Make sure that the spin phase is not off. Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'. Make sure that the this is not a balance problem. Adjust manually the items in the drum and start the spin phase again. There is water on the floor.
ENGLISH 37 Problem Possible solution The washing cycle is shorter than the time displayed. The appliance calculates a new time according to the laundry load. The washing cycle is longer than the time displayed. An unbalanced laundry load increases the duration time. This is a normal behaviour of the appliance. After a steam programme, garments are partially wet. Make sure that the appliance is accurately levelled. Adjust the appliance by raising or lowering the feet.
www.aeg.com Make sure that the water level inside the drum is not too high. Proceed with an emergency drain, if necessary (refer to «Emergency drain» in «Care and cleaning» chapter). To open the door, proceed as follows: 1. Press the button On/Off to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Keep the emergency unlock trigger pulled downward and, at the same time, open the appliance door. 5.
ENGLISH 39 • Remove the cardboard top. • Remove the polystyrene packaging materials. • Remove the internal film. • Open the door. • Remove the polystyrene piece from the door seal and all the items from the drum. • Put one of the polystyrene packaging elements on the floor behind the appliance. • Carefully put down the appliance with the rear side on it. • Make sure not to damage the hoses. • Remove the polystyrene protection from the bottom.
www.aeg.com • Pull up the appliance in vertical position. • Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliances in factory. • Remove the three bolts. • Use the key supplied with the appliance. • Pull out the plastic spacers. • Put the plastic caps in the holes. • You can find these caps in the user manual bag.
ENGLISH 16.3 Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under 41 the appliance, secured to at least 2 floor beams with screws, the wood panel must extend beyond the front feet. If possible install the appliance in one of the corners of the room, where the floor is more stable. 16.
www.aeg.com • The appliance must be level and stable. CAUTION! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. 16.6 The inlet hose • Connect the hose to the back appliance. Turn the inlet hose only left or right. • Loose the ring nut to set it in the correct position. 45 20 O O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings.
ENGLISH 43 • Making an U form with the drain hose. On the edge of a sink • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. To a stand pipe with vent-hole • Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). Refer to the illustration. • The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm - min. 1.
www.aeg.com To a sink spigot • Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. • Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. To a wall-pipe • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 17.
ENGLISH Spin Speed Wool 1 Maximum 1600 rpm 45 This product contains HFC - R134a/GWP1430 0.12 kg fluorinated gas hermetically sealed. 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 2) The appliance works correctly if the water pressure is not less than 0.05 MPa (0.5 bar). If you can not connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to have more than a distance of 5.02 m (16.
www.aeg.
ENGLISH 47
132908865-A-472016 www.aeg.