ÖKO-LAVAMAT 86741 updatee The environmentally friendly washing machine User information
Dear Customer, Please read this instruction book carefully before using the appliance. Please ensure you fully understand the safety instructions on the first pages of this instruction book. Retain the instruction book for future reference, and pass it on to any future owners. 1 The warning triangle and / or key words (Warning!, Caution!, Important!) give information that is important for your safety or the function of the appliance is highlighted. It is imperative that this information is observed. 0 1.
Contents Operating Instructions .................................... 6 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Environmental tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . .
Washing Programme Progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Washing cycle complete/Removing the washing . . . . . . . . . . . . . . . . . . . . 26 Programme Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separate Rinse/Conditioning/Starching/Treating . . . . . . . . . . . . . . . . . . . .
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inlet Hose Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions Operating Instructions 1 Safety The safety features of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. However, we also consider it our obligation as a manufacturer to inform you about the following safety information. Prior to initial start-up • Observe the "Installation and Connection Instructions" in this instruction book.
Operating Instructions Child Safety • Packaging materials (e.g. films, styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children. • This appliance is designed to be operated by adults. Do not allow children to tamper with the controls or play with the appliance. • Pets and children have been known to climb into washing machines. Please check the drum before use. • When disposing of the appliance, cut off the mains cable, and destroy the plug.
Operating Instructions 2 Disposal Packaging Dispose of the packaging material correctly. All packaging materials used are environmentally friendly and can be disposed of without any danger to the environment. • Plastic parts can be recycled and are identified as follows: for polyethylene, e.g. the outer covering and the bags in >PE< the interior. >PS< for polystyrene, e.g. padding (always CFC-free) >POM< for polyoxymethylene, e.g.
Operating Instructions Description of the Appliance Front view Detergent dispenser drawer Control panel Rating plate (behind door) Main door Screw feet (height-adjustable); rear left: Automatic adjustment foot. Flap in front of drain pump Detergent dispenser drawer Stain removers Main wash detergent in powder form and water softening agent if required. Pre-wash detergent/ soaking agent or water softening agent if used.
Operating Instructions Control Panel Program Spin speed/ Progress-Display RINSE HOLD button Additional ProgrammeProgramme Selector DOOR/LIGHT button Options Multi display START/ PAUSE Button DELAY TIMER Button OVERDOSING indicator Programme selector The programme selector is used to select the type of wash cycle (for example, water level, drum movement, number of rinses, spin speed) and the water temperature according to type of washing.
Operating Instructions STARCHING Separate starching, separate conditioning, separate treatment of damp clothes (1 rinse, liquid conditioner is washed in from the æ compartment, spin). This can also be selected if a separate rinse is necessary. In this case, you do not need to add anything to the compartment. DRAIN To drain the water after a rinse hold (without spinning). 3 The effect of Rinse Hold is that the washing is left to soak in the last rinse water; it is not spun.
Operating Instructions EASY IRON Wash programme at 40 °C for easy-care items which, after this programme, are to be ironed only lightly or not at all. 2 ENERGY SAVING Special energy and water saving programme at about 60 °C, for lightly to normally soiled Cottons/Coloureds (cotton/linen), with extended wash time. Programme Option Buttons The programme option buttons are used to adapt the programme to suit the degree of soiling of the wash.
Operating Instructions TIME SAVER Shortened wash programme for lightly soiled washing, consisting of three stages with the COTTONS/LINEN, EASY-CARES programme and two stages with the other programmes. Length of programmes Programme COTTONS/LINEN, EASYCARES at 60 °C Other programmes, for example DELICATES at 30 °C Without TIME SAVER With TIME SAVER Button pressed once Button pressed twice 119 mins. 91 mins. 63 mins. 68 mins. 52 mins.
Operating Instructions Consumption Values and Programme Times The following table gives the values for selected programmes under standard conditions. Consumption values depend on the selected programme settings (optional functions), washing type and quantity, water pressure, such as water inlet temperature, water hardness, room temperature or detergent used, etc. The tables do, however, give a helpful guide for normal household use.
Operating Instructions What does "UPDATE" mean? The control system of your washing machine is fully electronic. The software which determines this control system can be reprogrammed. If a further improvement to washing technology is introduced by AEG, then your machine can be updated. The cost of the UPDATE will be advised at the time of the request. For further information regarding this, please contact the AEG Customer Care Department.
Operating Instructions Before the first wash 0 Run a washing programme without laundry (selecting COTTONS/LINEN, EASY-CARES 95, with half the normal amount of detergent). This removes any residues from the drum which may have been left during manufacturing. Preparing for a wash cycle Sorting and preparing the washing • Sort the washing according to care symbols (see Section "Types of washing and care symbols"). • Empty out the pockets. • Remove metal objects (such as paper clips, safety pins, etc.).
Operating Instructions Types of washing and care symbols Care symbols help you to choose the correct wash programme. Washing should be sorted by type and according to care symbols. The temperatures indicated on the care symbols are the maximum wash temperatures. Cottons ç Cotton and linen items with this care symbol are not sensitive to machine washing or high temperatures. The COTTONS/LINEN, EASY-CARES programme is suitable for this type of washing.
Operating Instructions Detergents and Conditioners Which detergent and conditioner? Use only detergents and conditioners which are suitable for use in automatic washing machines. Always follow the manufacturer's instructions.
Operating Instructions Running a washing cycle Brief instructions A washing cycle consists of the following steps: 0 1. Set the appropriate washing programme: – Set the programme and temperature using the programme selector – Select any programme options if required 2. Change the Spin Speed/select RINSE HOLD as necessary. 3. Set the DELAY TIMER as required. 4. Open the door and load the washing. 5. Close the door. 6. Add detergent/conditioner. 7.
Operating Instructions 2. If required, select the programme option(s). The indicator display of the selected option lights up. – To change the option press another button. – To cancel a selection, press the button again. Changing Spin Speed /selecting RINSE HOLD 0 To change Spin Speed for the final spin (if necessary)/select RINSE HOLD: Press the Spin Speed/RINSE HOLD button as often as necessary, until the indicator light for the desired speed (or Rinse Hold) is lit.
Operating Instructions Setting the delay timer/soaking duration Delay timer The DELAY TIMER button makes it possible to delay the start of a wash programme by 1 to a maximum of 19 hours. 0 1. Select wash programme. 2. Press DELAY TIMER button. When start delay has been set, the DELAY TIMER display lights up. Depress the DELAY TIMER button until the desired start delay appears, e. g. 12h for a 12 hour delay to the start of the programme.
Operating Instructions Opening and closing the door 0 0 3 Open: Press the DOOR/LIGHT button. The door springs open. Close: Press the door firmly closed. When the unit is switched on, the DOOR/LIGHT display shows whether the door can be opened: – green: The door can be opened (not when programming is activated, see the section "Programme protection“ for details) – off: Door cannot be opened – red: Door is open The washing drum is illuminated when the door is open.
Operating Instructions Adding detergent/conditioners For instructions concerning detergent and conditioners, see Section “Detergents and conditioners”. 0 1. Open the detergent dispenser additives drawer : press the flap so as to be able to grasp the handle (1), and pull out the drawer (2). 3 2. Add the detergent/conditioners.
Operating Instructions 3 If using liquid detergents/tablets: Add liquid detergent or tablets in the quantity recommended by the washing detergent manufacturer. Add liquid detergent with the dosage container provided by the detergent manufacturer. Starting the wash programme 0 1. Check that the water tap is open. 2. Starting the wash programme: Press the START/PAUSE button. The wash programme is started or starts after the end of the time delay set.
Operating Instructions Washing Programme Progress Programme progress display Prior to the start, the programme steps chosen are displayed by the Programme progress display. During the washing programme the current programme step is displayed. Multi display The expected time remaining (in minutes) up to the end of the programme is shown in the Multi display. 3 The multi display indicates the estimated duration, in minutes, of the programme.
Operating Instructions Washing cycle complete/Removing the washing Once the wash programme has come to an endm the END indicator illuminates on the programme progress display. • If the EASY IRON programme was selected, and anti-crease phase of approximately 30 minutes follows the programme end. Here, the multi display shows the remaining time and the END indicator illuminates. During the anti-creasing phase, the door can be opened at any time and the washing can be removed.
Operating Instructions Programme Tables Washing The tables do not show all the possible settings, only those most likely to be selected for everyday purposes. Type of washing, Care symbol Cottons/Coloureds2) èç Cottons/Coloureds ëèç Max.
Operating Instructions Type of washing, Care symbol Max. Load (Dry weight)1) Possible Programme options or functions Programme selector Temperature [in °C] Wool/ Handwash 9ìï 2kg WOOL/P COLD to 40 Silk/Handwash ï 1kg SILK/P 30 TIME SAVER 1) A 10 litre bucket holds around 2.5kg of dry clothes (cotton). 2) Programme settings for testing in accordance with or in support of standard EN 60 456 and IEC 60 456, are described in the Chapter “Consumption Values and Programme Times“.
Operating Instructions Maintenance and Cleaning Control panel 0 Important! Do not use household furniture polish or abrasive cleaners to clean panel and operating parts. Wipe over the operating panels with a damp cloth. Use warm water. Detergent Dispenser Drawer The detergent dispenser drawer should be cleaned from time to time. 0 1. Pull the detergent dispenser drawer out as far as it will go. 2. Remove the detergent dispenser drawer by pulling sharply. 3.
Operating Instructions 7. Use a brush to clean the entire compartment area of the washing machine, particularly also the nozzles on the top side of the compartment. 8. Set the detergent dispensing drawer into the guide tracks and push it in. Washing Machine Drum 0 The washing machine drum is made from rust-free stainless steel. Any objects left in the laundry which are likely to rust can stain the drum.
Operating Instructions Cleaning the drain pump Paper clips, nails and so on can sometimes get into the washing machine with the washing and remain in the drain pump casing. Fluff and strands of fabric can gather on these items and block the drain pump. Therefore the drain pump should be cleaned at least once a year. Warning! Switch off the washing machine and pull out the mains plug before cleaning the drain pump. 0 1. First carry out emergency emptying (see section "Carrying out emergency emptying“). 2.
Operating Instructions What to do if... Trouble Shooting If the appliance is not working correctly, please carry out the following checks before contacting your local Service Force Centre. Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is in guarantee. • If the fault code C1 oder C2 is shown in the multi-display, you may be able to remedy the fault yourself (see the Fault table below).
Operating Instructions Problem Possible cause Remedy Transport packaging has not been removed. Remove transport packaging according to setting up and connection instructions. The machine is not level. Adjust the feet according to installation and connection instructions. Washing machine viThere is very little washing in brates during operation the drum (e.g. only a dressing This does not affect the operation of the machine. or is unstable. gown).
Operating Instructions Problem Possible cause Remedy The drain pump runs constantly - even when The Aqua Control anti-flood the appliance is system has been activated. switched off. Close the water tap, remove the mains plug and inform your local Service Force Centre. Fabric softener was not rinsed in, compartment æ for conditioners is filled with water. The insert in the compartiment for conditioners is not correctly attached or is blokked.
Operating Instructions Problem The rinse water is cloudy. Possible cause The cause is probably a detergent with a high silicate content. Remedy No negative influence on the rinse results, use a liquid detergent if necessary. When pressing a proThe selected programme opgramme option button tion cannot be combined Make another selection. the corresponding diswith the set programme. play does not light up.
Operating Instructions If the washing results are not satisfactory If the washing turns greyish and limescale deposits are present in the drum • Insufficient detergent has been added. • Incorrect detergent was used. • Stains were not pre-treated. • Programme or temperature was not set correctly. • If using modular detergents, the individual components were not used in the correct ratio.
Operating Instructions Carrying out an emergency emptying • If the washing machine no longer pumps out the water, emergency emptying must be carried out. • If the washing machine is located in a room in which below freezing temperatures might occur, emergency emptying must be carried out. Furthermore: unscrew the inlet hose from the water tap and drain off the water. Empty the drainage hose. Warning! Switch off the washing machine and pull out the mains plug prior to performing emergency emptying.
Operating Instructions When the water is completely drained: 6. Push the plug securely into the emergency emptying hose and turn it clockwise to secure it. 7. Replace the emergency emptying hose in its holder. 8. Put on the flap and close. Emergency unlocking of the door If the door cannot be opened, it can be opened using the emergency unlock feature. Warning! If it is necessary to unlock the door manually, always ensure that the washing machine has been disconnected from the electricity supply first.
Operating Instructions Additional rinse cycle (RINSE+) The washing machine is set for very economical water consumption. However, for people who suffer from allergies to detergents, it can be helpful to rinse with extra water. 3 If this function is selected, an extra rinse is added to the COTTONS/ LINEN, EASY-CARES, EASY IRON and DELICATES programmes. When delivered, the machine is not set for the additional rinse. To set the additional rinse: 0 1. Turn the programme selector to SHORT SPIN. 2.
Operating Instructions Water cooling It may be necessary to cool the water before draining, to prevent thermal damage to the plastic outlet pipes. 3 The water is cooled before draining out at the end of the main wash (by adding cold water). (This setting is only available with the COTTONS/LINEN, EASY-CARES programmes, with temperatures over 40 °C.) When the washing machine is delivered, water cooling is not set, except for the SENSITIVE programme option. To set the water cooling function: 0 1.
Operating Instructions Variomatic spin The variomatic spin is integrated into the final spin. The washing does not cling to the side of the drum as much and can be taken out more easily. This can be set with the COTTONS/LINEN, EASY-CARES programmes. To set Variomatic Spin: 0 1. Turn the programme selector to SHORT SPIN. 2. Press and hold the STAIN button for at least 5 seconds. When the button has been pressed for 5 seconds, the END light flashes on the Programme Progress display for 5 seconds. 3.
Operating Instructions Programme Protection To protect a programme setting against unintentional changes or tampering (for example, programme selector turned or buttons pressed accidentally, etc.), set the Programme Protection. This will protect your washing from damage. 3 The Programme Protection can be set or released at any time while the programme is running. Setting the Programme Protection: 0 1. Set the desired programme. 2. Press the START/PAUSE button to start the programme. 3.
Operating Instructions Child Safety Feature If the child safety feature is set, the door cannot be closed and no washing programme can be started. 0 1 0 Setting the child safety feature Use a coin to turn the rotary knob on the inside of the door clockwise as far as it will go. Warning! The rotary knob must not be in a vertical position after adjustment, otherwise the child safety feature is not active. The rotary knob must project as shown in the diagram.
Installation and connection instructions Installation and connection instructions Installation Safety Precautions • When moving do not tilt the washing machine onto its front or onto its right hand side (viewed from the front). This is to prevent the possibility of the electronic components becoming wet. • Before installation inspect the machine for transport damage. Do not connect the appliance if it is damaged - contact your retailer.
Installation and connection instructions Installation of the appliance Transporting the appliance • Do not place the washing machine on its front or on its right hand side (viewed from the front). This is to prevent the possibility of the electronic components becoming wet. • Never transport the unit without the transport packaging and bolts/ bars. Do not remove the transport packaging until the appliance is at the installation location. Transporting the unit without the transport packaging can damage it.
Installation and connection instructions 3 46 The special spanner (E) and the caps (D) (2 each) and (G) (1 each) are supplied with it. 3. Remove the two screws (A) with the special spanner. 4. Remove the 4 screws (B). 5. Remove the transit bar (C). 6. Screw the 4 screws (B) back in for safe keeping. 7. Close the 2 large holes with the caps (D). Important! When fitting the plastic caps, press until they snap into the rear panel securely. 8.
Installation and connection instructions Installation-Site preparation • The installation surface must be clean, dry and level. Do not install on a deep pile carpet. • Minor unevenness of the floor surface should never be levelled out by laying pieces of wood, card or similar materials, but should always be compensated for by adjusting the screw feet. • If the appliance is installed next to a heat source (e.g.
Installation and connection instructions Levelling the appliance Self adjusting foot: The rear foot of your washing machine is designed like a spring leg. This makes the machine very stable even at high spin speeds. If the washing machine is still not stable during spinning, proceed as follows: 0 1. Set the three adjustable feet to the nominal value of 10 mm. Use the supplied spanner. If the self adjusting foot does not reach the floor: 2.
Installation and connection instructions Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING - THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is located at the top of the rim of the open door.
Installation and connection instructions Permanent Connection In the case of a permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point.
Installation and connection instructions Water connection 3 The washing machine is provided with safety devices preventing backcontamination of the water supply and complies with local water authority requirements. This appliance is designed to be permanently plumbed into your home’s water supply. Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.
Installation and connection instructions Inlet Hose Connection A pressure hose 1.5m in length is supplied. If a longer inflow hose is required, only a VDE-approved, complete set of hoses with fitted hose screw connections offered by your local Service Force Centre is permissible. – Hose sets in lengths of 2.2m, 3.5m and 5m are available for washing machines without Aqua Control. – Hose sets in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua Control.
Installation and connection instructions Water Drainage The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece“ supplied. The standpipe should have an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe. Important! It is essential to lay the drainage hose without kinks.
Installation and connection instructions If you intend the drain hose from the washing machine to empty into a sink, make sure that the sink is empty and the plug hose is not blocked. Use the plastic “U-Piece“ supplied. Important! The end of the drainage hose must not be submerged in the pumped-out water. Otherwise, the water could be sucked back into the appliance.
Installation and connection instructions Technical Data Height adjustment Load (depending on programme) Area of use Drum spin speed Water pressure of about +10/-5mm up to 6kg Domestic see Rating Plate 1-10bar (=10–100N/cm2 = 0.1–1.
Warranty conditions Warranty conditions Great Britain 1. 2. 3. 4. 5. 6. 56 Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Index Index A Over-dosed . . . . . . . . . . . . . . . . . . . . . . . . . .26 Aqua Control . . . . . . . . . . . . . . . . . . . . .15, 26 Automatic adjustment foot . . . . . . . . . . 9, 48 P C Child safety feature . . . . . . . . . . . . . . .32, Circulation pump . . . . . . . . . . . . . . . . . . 9, Coloureds . . . . . . . . . . . . . . . . . . . . 17, 27, Conditioner . . . . . . . . . . . . . . . . 9, 18, 19, Conditioning . . . . . . . . . . . . . . . . . . . . .11, Correcting the programme . . .
Service & Spare Parts Service & Spare Parts If after carrying out the necessary checks there is still a fault with your appliance please contact your local AEG Service Force Centre. In guarantee customers should ensure that the suggested checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for in-guarantee service calls.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
