L 76285 FL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
ENGLISH Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. 2.2 Use WARNING! Risk of injury, electrical shock, fire, burns or damage to the appliance.
www.aeg.com Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Maximum load Cotton 8 kg Spin speed Maximum 1200 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 4.
ENGLISH 7 4.2 Accessories 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink. 3 5. CONTROL PANEL 1 2 3 Anti-rugas Algodões Refrescar Algodões Eco Super Eco Extra Silencioso + Pré-lavagem Sintéticos 20 min.
www.aeg.com • After 5 minutes from the end of the washing programme. Refer to 'At the end of programme'. 5.2 Programme knob 2 Turn this knob to set a programme. The related programme indicator comes on. 5.3 Display 3 A B C D The display shows: A • The maximum temperature of the programme. B • The default spin speed of the programme. • 'No Spin'1) and 'Rinse Hold' symbols. C • The display symbols.
ENGLISH D 9 • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme. – You change the programme while it operates.
www.aeg.com Spin phase is off. 'Rinse Hold' function is on. 5.10 Temperature button 10 Press button 10 to change the default temperature. -- = cold water • To activate the function, press button 10 and button 9 at the same time until the display shows the symbol . • To deactivate the function, press button 10 and button 9 at the same time until the symbol goes off. You can activate the function: • Before you press the Start/Pause button 4 : the appliance cannot start.
ENGLISH 11 Programme Temperature Type of load max. weight of load Cycle description Functions Extra Silencioso 95° - Cold White and coloured cotton with normal soil. max. 8 kg Stop with water in the drum Rinses Long spin STAIN EXTRA RINSE TIME SAVE1) Sintéticos 60° - Cold Synthetic or mixed fabric items with normal level of soil. max. 4 kg Wash Rinses Short spin SPIN REDUCTION RINSE HOLD STAIN EXTRA RINSE TIME SAVE1) Engomar Fácil2) 60° - Cold Synthetic fabric items with normal soil. max.
www.aeg.com Programme Temperature Type of load max. weight of load 20 Min. - 3 kg 40° - 30° Cotton and synthet- Wash ic items with light Rinses soil or worn only Short spin one time. SPIN REDUCTION Super Eco4) Cold Mixed fabrics (cotton and synthetic items). max. 3 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD EXTRA RINSE White and fast coloured cotton with normal soil. max.
ENGLISH Programme1) Type of load 13 Max. load Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry more smooth. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam programmes do not perform any hygienic cycle. Do not set the Steam programme for this type of clothes: • Clothes which is not specified on the care label as being suitable for tumbledrying.
www.aeg.com Programmes Load (Kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) Synthetics 40 °C 4 0.60 50 110 35 Delicates 40 °C 4 0.70 60 91 35 Wool/Hand wash 30 °C 2 0.35 57 58 30 Standard cotton programmes Standard 60 °C cotton 8 0.90 58 208 53 Standard 60 °C cotton 4 0.65 45 156 53 Standard 40 °C cotton 4 0.49 44 156 53 1) At the end of spin phase. Off Mode (W) Left On Mode (W) 0.
ENGLISH Make sure not to put too much laundry in the drum. 3. 15 Close the door. Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 9.2 Filling the detergent and additives The detergent compartment for the prewash phase and the soak programme. Add the detergent for prewash and soak before the start of the programme. The detergent compartment for the washing phase.
www.aeg.com Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6.
ENGLISH 5. When the countdown is completed, the programme starts automatically. Press button 4 to start the programme. The indicator of button 4 is on. Before you press button 4 to start the appliance, you can cancel or change the set of the delay start. You cannot set the delay start with the Steam programme. The drain pump can operate for a short time when the appliance fills water.
www.aeg.com • The door lock symbol goes off. • Press button 1 to deactivate the appliance. After five minutes from the end of the programme, the energy saving function automatically deactivates the appliance. – The door stays locked. – You must drain the water to open the door. When you activate the appliance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty.
ENGLISH • Do not mix different types of detergents. • To help the environment, do not use more than the correct quantity of detergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the programme temperature and the level of soil. • If you use liquid detergents, do not set the prewash phase. • If your appliance has not the detergent dispenser with the flap device, add the liquid detergents with a dosing ball.
www.aeg.com • Set the hottest cotton wash programme • Use a correct quantity of powder detergent with biological properties. After each wash, keep the door open for a while to prevent mould and to let unpleasant smells go out. 11.4 Door seal Regularly examine the seal and remove all objects from the inner part. 11.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum.
ENGLISH 5. 6. 11.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 21 Clean the dispenser recess with a brush. Put back the dispenser in the recess. • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump.
www.aeg.com 5. 1 6. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump. Pull back the drainage duct and turn the filter to remove it. 2 2 1 11.8 The inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. 7.
ENGLISH 23 To clean the water inlet filters: Close the water tap. Remove the water inlet hose from the water tap. 3. Clean the filter in the inlet hose with a stiff brush. 1. 2. 4. 5. 6. 7. 20° Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 11.9 Emergency drain Because of a malfunction, the appliance cannot drain the water.
www.aeg.com 12. TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. • - The anti-flood device is on.
ENGLISH Problem Possible cause The anti-flood device is on. The spin phase does not operate. The programme does not start. There is water on the floor. 25 Possible solution • Disconnect the appliance. • Close the water tap. • Contact the service centre. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load.
www.aeg.com Problem Possible cause Possible solution The appliance fills The end of the drain with water and hose is too low. drain immediately. The washing results are not satisfactory. Make sure that the drain hose is in the correct position. The detergent you used Increase the detergent quantity was not sufficient or cor- or use a different one. rect. You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains.
ENGLISH 27 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses.
www.aeg.com 7. 8. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag.
ENGLISH WARNING! Remove all the packaging and the transit bolts before you install the appliance. 29 We recommend that you keep the packaging and the transit bolts for when you move the appliance. 13.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level.
www.aeg.com • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
ENGLISH 31 • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
www.aeg.com 14. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
ENGLISH 33
www.aeg.
ENGLISH 35
132916910-A-102013 www.aeg.
