L 76285 FL L 76482 FL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT DESCRIPTION . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
2. www.aeg.com SAFETY INSTRUCTIONS 2.1 Installation • Remove all the packaging and the transit bolts. • Keep the transit bolts. When you move the appliance again you must block the drum. • Do not install or use a damaged appliance. • Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the weather. • Obey the installation instruction supplied with the appliance.
ENGLISH 2.3 Care and Cleaning WARNING! Risk of injury or damage to the appliance. • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. • Do not use water spray and steam to clean the appliance. • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive 5 cleaning pads, solvents or metal objects. 2.4 Disposal WARNING! Risk of injury or suffocation. • Disconnect the appliance from the mains supply.
www.aeg.com 4. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 12 7 1 Worktop 8 Water drain hose 2 Detergent dispenser 9 Water inlet valve 3 Control panel 4 Door handle 10 Mains cable 5 Rating plate 12 Feet for the appliance level 11 Transit bolts 6 Drain pump 7 Feet for the appliance level 1 2 4.1 Accessories 1 Spanner To remove the transit bolts. 2 Plastic caps 4 3 To close the holes on the rear side of the cabinet after the removal of the transit bolts.
ENGLISH 7 5. CONTROL PANEL 1 2 3 Ατμός Βαμβακερά Φρεσκάρισμα Βαµβακερά Eco Super Eco + Πρόπλυση Αθόρυβο Συνθετικά 20 λεπτά - 3 κιλά Εύκολο Σιδέρωμα Τζήν Ευαίσθητα Μάλλινα/ Μεταξωτά Κουβέρτα Ξέβγαλμα Στύψιμο/ ´Aδειασμα Θερμοκρ. Στύψιμο 10 1 On/Off button (On/Off) 2 Programme knob 3 Display 4 Start Pause button (Εναρξη/Παύση) 5 Delay start button (Καθυστ. Εναρξης) 6 Time saving button (Εξοιk. Xρóνου) 7 Extra rinse button (Επιπλ. Ξέβγαλ.
www.aeg.com C • The display symbols.2) Symbols Description Washing phase Rinse phases Spin phase Child lock You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off. If the programme is completed but the symbol stays on: • There is water in the drum. • The 'Rinse Hold' function is on. Delay start D • The programme time When the programme starts, the time decreases with steps of 1 minute.
ENGLISH 5.7 Extra rinse button 7 Press button 7 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. 5.8 Stain button 8 Press button 8 to add the stain phase to a programme. Use this function for laundry with hard stains to remove. When you set this function, put the stain . remover into compartment This function increases the programme duration. This function is not available with a temperature lower than 40° C. 5.
www.aeg.com 6. PROGRAMMES Programme Temperature Type of load Cycle max. weight of load description Functions Βαμβακερά 95° - Cold White and coloured cotton with normal soil. max. 8 kg Wash Rinses Long spin SPIN REDUCTION NO SPIN RINSE HOLD ΛΕΚΈΔ ΕΠΙΠΛ. ΞΈΒΓΑΛ. ΕΞΟΙΚ. ΧΡΌΝΟΥ1) Βαμβακερά + Πρόπλυση 95° - Cold White and coloured cotton with heavy soil. max. 8 kg Prewash Wash Rinses Long spin SPIN REDUCTION NO SPIN RINSE HOLD ΕΠΙΠΛ. ΞΈΒΓΑΛ. ΕΞΟΙΚ.
ENGLISH 11 Programme Temperature Type of load Cycle max. weight of load description Functions Μάλλινα/ Machine washable Wash wool. Hand washable Rinses wool and delicate Short spin fabrics with «hand washing» care symbol. max. 2 kg SPIN REDUCTION NO SPIN RINSE HOLD Κουβέρτα 60° - 30° One synthetic blanket, duvet, bedspread and so on. max. 2 kg Wash Rinses Short spin SPIN REDUCTION Στύψιμο/ Αδειασμα3) All fabrics The maximum load of the laundry is related to the type of laundry.
www.aeg.com 3) The default phase of the spin speed is related to cotton items. Set the spin speed. Make sure that it agrees with the laundry. 4) Set this programme to decrease the time and the consumption of energy and water. 5) Standard programmes for the Energy Label consumption values] according to regulation 1061/2010, the “Βαμβακερά Eco 60° C” and “Βαμβακερά Eco 40° C” are respectively the “standard 60° C cotton programme” and the “standard 40° C cotton programme”.
ENGLISH Programmes Load (kg) Energy consumption (kWh) Water consumption (litre) Cottons 60 °C 8 1.60 72 168 53 52 Cottons 40 °C 8 1.00 72 164 53 52 Synthetics 40 °C 4 0.60 50 110 35 35 Delicates 40 °C 4 0.70 60 91 35 35 Wool/Hand wash 30 °C 2 0.35 57 58 30 30 13 Approxi- Remain- Remainmate ing ing promoismoisgramme ture ture duration (%)1) (%)1) (miL 76285 L 76482 nutes) FL FL Standard cotton programmes Standard 60 °C cotton 8 0.
www.aeg.com 3. Press button 1 to activate the appliance. 4. Put the laundry in the appliance. 5. Use the correct quantity of detergent and additives. 6. Set and start the correct programme for the type of laundry and soil. 2. Put the laundry in the drum, one item at a time. Shake the items before you put them in the appliance. Make sure not to put too much laundry in the drum. 3. Close the door. 8.1 Loading the laundry 1. Open the appliance door.
ENGLISH 15 The compartment for the stain remover. Put the product in the compartment and set the stain function before you start the programme. Flap for powder or liquid detergent Turn it (up or down) in the correct position to use powder or liquid detergent. Always obey the instructions that you find on the packaging of the detergent products. Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3.
www.aeg.com 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser. Make sure that the flap does not cause a blockage when you close the drawer. 8.3 Setting and starting a programme 1. 2. Turn the programme knob. The related programme indicator comes on. The appliance does not drain the water. 2. The indicator of button 4 flashes with red colour. 3. The display shows the default temperature and spin speed.
ENGLISH To open the appliance door: 1. Press button 4 . The door lock symbol in the display goes off. 2. Open the appliance door. 3. Close the appliance door and press button 4 . The programme or the delay start continues. If the temperature and level of the water in the drum are too high, the door lock symbol stays on and you cannot open the door. To open the door do the steps that follow: 1. Deactivate the appliance. 2. Wait for some minutes. 3. Make sure that no water is in the drum.
www.aeg.com • Wash with a special detergent heavy soil stains. • Be careful with the curtains. Remove the hooks or put the curtains in a washing bag or pillowcase. • Do not wash in the appliance : – Laundry without hems or with cuts – Underwired bras. – Use a washing bag to wash small items. • A very small load can cause balance problems with the spin phase. If this occurs, adjust manually the items in the tub and start the spin phase again. 9.
ENGLISH 19 The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales. Use a special product made for washing machines. Obey the instructions that you find on the packaging of the manufacturer. Do this separately from the laundry wash. the drum. Make regularly a maintenance wash. To do this: • Empty the laundry from the drum. • Set the hottest cotton wash programme • Use a correct quantity of powder detergent with biological properties.
www.aeg.com 3. 4. 5. 6. 10.7 Drain pump Regularly examine the drain pump and make sure that it is clean. Remove the top part of the liquid additive compartment. Clean all the parts with water. Clean the dispenser recess with a brush. Put back the dispenser in the recess. • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates.
ENGLISH 3. 4. 5. 1 6. 21 Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump. Pull back the drainage duct and turn the filter to remove it. 2 2 1 10.
www.aeg.com To clean the water inlet filters: Close the water tap. Remove the water inlet hose from the water tap. 3. Clean the filter in the inlet hose with a stiff brush. 1. 2. 4. 5. 6. 7. 20° Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 10.9 Emergency drain Because of a malfunction, the appliance cannot drain the water.
ENGLISH 23 11. TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. • - The anti-flood device is on.
www.aeg.com Problem Possible cause The anti-flood device is on. The spin phase does not operate. The programme does not start. There is water on the floor. Possible solution • Disconnect the appliance. • Close the water tap. • Contact the service centre. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load.
ENGLISH Problem Possible cause Possible solution The appliance fills The end of the drain with water and hose is too low. drain immediately. The washing results are not satisfactory. 25 Make sure that the drain hose is in the correct position. The detergent you used Increase the detergent quantity was not sufficient or cor- or use a different one. rect. You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains.
www.aeg.com 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses.
ENGLISH 7. 8. 27 Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag.
www.aeg.com WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 12.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level.
ENGLISH 29 • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
www.aeg.com • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
ENGLISH 13. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
132918160-A-322012 www.aeg.
