L 75480 WD EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 10. 11. 12. 13. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
ENGLISH Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. 2.2 Use WARNING! Risk of injury, electrical shock, fire, burns or damage to the appliance.
www.aeg.com • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance. 3.
ENGLISH 7 4. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 7 1 Worktop 2 Detergent dispenser 3 Control panel 4 Door handle 5 Rating plate 6 Drain pump 7 Feet for the appliance level 8 Water drain hose 9 Water inlet valve 10 Mains cable 11 Transit bolts 12 Feet for the appliance level 4.1 Child safety device • When you activate this device, you cannot close the door. This prevents 12 children or pets to be closed in the drum. To activate the device, turn it clockwise, until the groove is horizontal.
www.aeg.com 4.2 Accessories 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink. 3 5. CONTROL PANEL 1 2 Katoen Eco Blanc/Couleurs +Voorwas Super Eco +Prélavage Synthetica Non Stop 60 Min.
ENGLISH – Set again the washing programme and all possible options. • After 5 minutes from the end of the washing programme. Refer to 'At the end of programme'. 5.2 Programme knob 2 Turn this knob to set a programme. The related programme indicator comes on. 5.3 Display 3 A B C D The display shows: A • The maximum temperature of the programme. B • The default spin speed of the programme. • 'No Spin'1) and 'Rinse Hold' symbols.
www.aeg.com D • The programme time (washing and/or drying phase) When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme.
ENGLISH 5.10 Spin button 9 Press this button to: • Decrease the maximum speed of the spin phase when you set a programme. The display shows only the spin speeds available with the set programme. • Deactivate the spin phase. • Activate the 'Rinse Hold' function. Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed. Spin phase is off. 'Rinse Hold' function is on. 5.11 Temperature button 10 Press button 10 to change the default temperature.
www.aeg.com Programme Temperature Type of load max. weight of load Cycle description Functions Synthetica Synthétiques Synthetics 60° - Cold Synthetic or mixed fabric items with normal level of soil. max. 4 kg Wash Rinses Short spin SPIN REDUCTION RINSE HOLD EXTRA RINSE1) TIME SAVE2) Synthetica + Voorwas Synthétiques + Prélavage Synthetics + Prewash 60° - Cold Synthetic or mixed fabric items with heavy soil. max.
ENGLISH Programme Temperature Type of load max. weight of load Cycle description Functions Schleudern / Pumpen Essorage / Vidange5) Spin / Drain All fabrics The maximum load of the laundry is related to the type of laundry. Drainage of the water Spin phase at the maximum speed. SPIN REDUCTION NO SPIN6) 13 DRYING PROGRAMMES Wol Laine Wool Synthetica Synthétiques Synthetics Katoen Blanc/Couleurs Cotton Non Stop 60 Min. 30° Wool items max. 1 kg Timed drying only Synthetic items max.
www.aeg.com 2) If you press the button 6 two times (Extra Quick duration), we recommend that you decrease the quantity of the load. It is possible to load fully the appliance, however the washing results are reduced. 3) This programme it is not compatible with drying. 4) During this cycle the drum rotates slowly to ensure a gentle washing. It can seem that the drum doesn't rotate or doesn't rotate properly. Consider this as a normal functioning of the appliance.
ENGLISH 15 6.2 Programmes for timed drying Degree of drying Type of fabric Extra dry Cotton and linen For towelling mate- (bathrobes, bath towels, rials etc) Cupboard dry1) For items to put away Cotton and linen (bathrobes, bath towels, etc) Cupboard dry For items to put away Synthetics and mixed fabrics (jumpers, blouses, underwear, household linen) Iron dry Suitable for ironing Wool dry Cotton and linen (sheets, tablecloths, shirts, etc.
www.aeg.com The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. 8. BEFORE FIRST USE 1. To activate the drain system, put 2 litre of water in the main wash compartment of the detergent dispenser. 2. Put a small quantity of detergent in the main wash compartment of the 1. 2. 3. Open the water tap. Connect the mains plug to the mains socket.
ENGLISH 17 9.2 Filling the detergent and additives The detergent compartment for the prewash phase, the soak programme and for the stain function. Add the detergent for prewash, soak and stain remover before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme.
www.aeg.com 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser.
ENGLISH 2. If the temperature and level of the water in the drum are too high, the door lock symbol stays on and you cannot open the door. To open the door do the steps that follow: 1. Deactivate the appliance. 2. Wait for some minutes. 3. Make sure that no water is in the drum. Press button 1 again to activate the appliance. Now, you can set a new washing programme. The appliance does not drain the water. 9.6 Change a function You can change only some functions before they operate. 1. Press button 4 .
www.aeg.com 2. Press the Start/Pause button 4 . The appliance drain the water and spin. 3. When the programme is completed and the door lock symbol goes off, you can open the door 4. Deactivate the appliance. The appliance drain and spin automatically after approximately 18 hours. 9.11 Drying only WARNING! Open the water tap. Put the drain hose in the sink or connect to the drain pipe. • Load the laundry. • Turn the programme dial to the programme suitable for the items to dry.
ENGLISH • When the door locked symbol goes off, you can open the door. • Remove the laundry from the appliance. Make sure that the drum is empty. • Keep the door ajar, to prevent mildew and odours. • Close the water tap. 9.12 NON-STOP programme Washing & Automatic drying CAUTION! Do not put a plastic device/ball for the detergent into the drum. • Press button 1 to activate the appliance. • Load the laundry. • Measure out the detergent and fabric conditioner.
www.aeg.com Set drying time value • After some seconds the display shows the total duration of the cycles. Final time value (washing + drying + anti-crease + cooling phases) If you set a drying time of only 10 minutes, the final time value includes also the anti-crease and the cooling phases. • Press button 4 to start the programme. The door is locked The display shows the new time value each minute. • When the programme is completed, the appliance stops automatically. • The acoustic signals operate.
ENGLISH • Be careful with the curtains. Remove the hooks or put the curtains in a washing bag or pillowcase. • Do not wash in the appliance : – Laundry without hems or with cuts – Underwired bras. – Use a washing bag to wash small items. • A very small load can cause balance problems with the spin phase. If this occurs, adjust manually the items in the tub and start the spin phase again. 23 • Obey the instructions that you find on the on packaging of these products.
www.aeg.com – – – – – – – Nylon stockings. Quilts. Bed covers. Duvets. Anoraks. Sleeping bags Fabrics with residue of hair sprays, nail solvents or similar. – Garments with foam-rubber or materials similar to foam-rubber. 10.6 Garment labels When you dry ther laundry, obey the indications on the labels of the manufacturers: • = The item can be tumble dried • = The drying cycle is at high temperature • = The drying cycle is at reduced temperature • = The item can not be tumble dried. 10.
ENGLISH 25 After each wash, keep the door open for a while to prevent mould and to let unpleasant smells go out. 11.4 Door seal Regularly examine the seal and remove all objects from the inner part. 11.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel.
www.aeg.com 5. 6. 11.7 Drain pump Regularly examine the drain pump and make sure that it is clean. Clean the dispenser recess with a brush. Put back the dispenser in the recess. • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump.
ENGLISH 5. 1 6. 27 When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump. Pull back the drainage duct and turn the filter to remove it. 2 2 1 11.8 The inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. 7. Remove fluff and objects from the pump.
www.aeg.com To clean the water inlet filters: Close the water tap. Remove the water inlet hose from the water tap. 3. Clean the filter in the inlet hose with a stiff brush. 1. 2. 4. 5. 6. 7. 20° Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 11.9 Emergency drain Because of a malfunction, the appliance cannot drain the water.
ENGLISH 29 12. TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water properly. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. • - The anti-flood device is on.
www.aeg.com Problem Possible cause The anti-flood device is on. The spin phase does not operate. The programme does not start. There is water on the floor. Possible solution • Disconnect the appliance. • Close the water tap. • Contact the service centre. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load.
ENGLISH Problem Possible cause Possible solution The appliance fills The end of the drain with water and hose is too low. drain immediately. The cycle is shorter than the time displayed. Make sure that the drain hose is in the correct position. The appliance calculates See the ‘Consumption Values’ a new time according to chapter. the laundry load. The cycle is longer An unbalanced laundry than the time dis- load increases the duraplayed. tion time. The washing results are not satisfactory.
www.aeg.com 13. INSTALLATION 13.1 Fixing plate kit (4055171146) Available from your authorized dealer. If you install the appliance on a plinth, secure the appliance in the fixing plates. Follow the instructions supplied with the kit. 13.2 Unpacking 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film.
ENGLISH 33 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8. 1 2 9. Remove the power supply cable and the drain hose from the hose holders.
www.aeg.com 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 13.3 Positioning and levelling • Install the appliance on a flat hard floor.
ENGLISH 35 • The appliance must be level and stable. CAUTION! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. 13.4 The inlet hose • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 20 O 45 O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings.
www.aeg.com Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault . If this occur, close the water tap and contact the service centre to replace the hose. A 13.5 Water drainage There are different procedures to connect the drain hose: With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains.
ENGLISH 37 Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 14.
www.aeg.
ENGLISH 39
132924732-A-452013 www.aeg.