LAVAMAT 66600 Washing Machine User information
Dear Customer, Please read this user information carefully and keep it to refer to later. Please pass the user information on to any future owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning! Information that affects your personal safety. Important! Information that prevents damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . .
Installation and connection instructions. . . . . . . . . . . . . . . . . 26 Safety information concerning installation . . . . . . . . . . . . . . . . . . . . . . . . 26 Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing the transit packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Where to install . . . .
Operating Instructions 1 Safety Prior to using the appliance for the first time • Follow the “Installation and connection instructions”. • If the appliance is delivered in the winter months when there are minus temperatures: store the washing machine at room temperature for 24 hours before using for the first time. Correct use • The washing machine is only designed for the washing of normal domestic laundry at home. • Additions or modifications to the washing machine are not permitted.
• Switch off the washing machine prior to cleaning it and carrying out maintenance. In addition, remove the power plug from the power point or – if the appliance has been hard-wired – switch off the cutout in the fuse box or completely remove the fuse. • If operation is stopped, disconnect the appliance from the mains supply and turn off the tap. • Never remove the power plug from the power point by pulling on the cable. Always pull the plug.
Description of the appliance Control panel Detergent drawer Rating plate (behind door) Plinth flap/ Drain pump Screw feet (height adjustable) Control panel Spin/RINSE HOLD button Multi-display Programme progress display DELAY TIMER button Additional programme buttons DOOR indicator Programme selector START/PAUSE button 7
Programme overview RINSE + TIME SAVER PRE WASH STAIN 1600 700 RINSE HOLD Spin speed max.
Application/Features Energy-saving programme which washes at 60 °C for lightly to normally soiled whites or coloureds made of cotton/linen. Care symbols1) MO Programme for normally to heavily soiled whites/coloureds made of cotton/linen. JMO Programme for easy-care mixed fibres and synthetics. IKN Special programme which washes at 40 °C for easy-care fabrics which after being washed using this programme need to be ironed only lightly or not at all.
Before the first wash 1. Open the detergent drawer. 2. Pour approx. 1 litre of water through the detergent drawer into the washing machine. This closes the water container when the next programme is started and the economy valve can function properly 3. To remove any production-related residues from the drum and water tank, perform the first wash cycle without a load. Programme: COTTONS/LINEN 60, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent.
Running a wash cycle Opening the door/loading washing 1. Open the door: pull the handle on the door. When the appliance is switched on, the DOOR and START/PAUSE indicators show whether the door can be opened: DOOR indicator START/PAUSE indicator Can the door be opened? illuminated green flashing red or not illuminated yes illuminated green illuminated red yes, after pressing the START/PAUSE button During the programme the door is locked when the water level or the temperature is high.
• Water softener should be used from water hardness range 2 (=medium). The amount of detergent used can then always be that as for hardness range 1 (=soft). Your local water company will provide you with information about water hardness in your area. 1. Pull out the detergent drawer as far as it will go. 2. Add the detergent/conditioner. 3. Push the detergent drawer in fully.
Switching on the appliance/selecting a programme Set the programme and temperature using the programme selector. 3 The appliance is switched on by selecting a programme. – The programme progress display shows the programme steps that the selected programme will carry out. – The estimated programme duration (in minutes) appears in the multi-display. Changing the spin speed/selecting rinse hold 3 The washing machine suggests the maximum permitted spin speed suitable for the selected programme.
Selecting additional programmes 3 If required, press additional programme button(s). The corresponding indicator will illuminate. If “Err” flashes in the multi-display, the selected additional programme cannot be used together with the wash programme set. RINSE + Two additional rinse cycles are carried out for the programmes ENERGY SAVING, COTTONS/LINEN, DELICATES, EASY-CARES and EASY IRON (for example in cases of over-sensitive skin). TIME SAVER Shortened wash programme for lightly soiled items.
3 If the display is showing 23h and you press the button again, the time delay will be cancelled. 0 will appear followed by the length of the wash programme that has been set. 3. To activate the delay timer, press the START/PAUSE button. The time remaining to the start of the programme will be continuously shown (e.g. 12h, 11h, 10h,... 30' etc.). Starting a programme 3 1. Check that the tap is turned on. 2. Select a programme. 3. Press the START/PAUSE button.
Interrupting a programme/adding washing Interrupting a programme • A programme can at any time be interrupted by pressing the START/ PAUSE button and resumed by pressing START/PAUSE again. • To cancel a programme before it has ended, turn the programme selector to OFF. Important: Be careful of water in the appliance. Adding washing Washing can be added, as long as the DOOR indicator is illuminated green. 1. Press the START/PAUSE button. The door can be opened. 2.
Child safety device If the child safety device has been activated, the door can no longer be shut. Activating the child safety device: Use a coin to turn the knob (on the inside of the door) in a clockwise direction as far as it will go. 1 Warning! The knob must not be depressed after being set, otherwise the child safety device is not activated. The knob must stand proud as shown in the illustration. Deactivating the child safety device: Turn the knob in an anti-clockwise direction as far as it will go.
Cleaning and care Important: Do not use furniture cleaning products or aggressive cleaning agents to clean the appliance. Wipe over the control panel and housing with a damp cloth. Detergent drawer The detergent drawer should be cleaned regularly. 1. Remove the detergent drawer by pulling firmly. 2. Remove the softener insert from the middle compartment. 3. Clean all parts with water. 4. Place the softener insert in as far as it will go, so that it is firmly in position. 5.
What to do if... Remedying small faults yourself If during use of the appliance one of the following error codes is shown in the multi-display: – E10 (Problems with the water inflow), – E20 (Problems with the water outflow), – E40 (door open), please consult the following table. After the error has been remedied, press the START/PAUSE button. In the event of other errors (E and a number or letter): Switch the appliance off and then on again. Set the programme again. Press the START/PAUSE button.
Problem E10 appears. The END indicator is flashing once, and simultaneously an acoustic signal is sounding once. (Problems with the water inflow.) Possible cause The tap is shut off. Remedy Turn on the tap. Turn off the tap. Unscrew the The filter in the inlet hose hose, remove the filter and screw connection is blocked. clean it. The tap is blocked by limes- Check the tap and have it recale or faulty. paired, if necessary. The transit packaging has not been removed.
Problem Conditioner has not been rinsed in, compartment w for conditioner is filled with water. Possible cause The softener insert in the Clean the detergent drawer, compartment for conditioninsert the conditioner insert ers has not been correctly firmly. inserted or is blocked. The door is locked. The door cannot be opened when the wash- There has been a power cut. ing machine is switched (All the indicators have gone out.) on. The door remains locked for approx. 4 to 10 minutes.
If the wash result is not satisfactory The washing is grey and there are limescale deposits in the drum • Too little detergent was used. • An incorrect detergent was used. • Individual stains were not pre-treated. • The programme or temperature was not set properly. There are grey stains on the washing • Items that were soiled with ointments, fats or oils were washed using too little detergent. • The wash temperature used was too low.
Carrying out an emergency drain 1 Warning! Prior to carrying out an emergency drain, switch off the washing machine and remove the power plug from the power point. Warning! The water that comes out of the emergency drain hose may be hot. There is a risk of scalding. Let the water cool before performing an emergency drain! 1. Open the plinth flap and remove it. 2. Remove the emergency drain hose. 3. Place a shallow container underneath it.
Drain pump 1 The drain pump is maintenance-free. It is only necessary to open the pump cover if there is a malfunction and water is no longer being pumped out, e.g. if the pump wheel is blocked. Before loading the machine, please always ensure that there are no foreign bodies present in the pockets or in between the items to be washed. Paper clips, nails, etc.
Technical data 5 This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x width x depth 850 x 598 x 603mm Depth when door is open 980 mm Height adjustment approx. +10/-5mm Load (depending on programme) max.
Installation and connection instructions 1 Safety information concerning installation • This washing machine cannot be built-in. • Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged to the mains. In the event of damage to the appliance contact your supplier. • Be sure to remove all the components of the transit packaging before using the appliance for the first time.
Installing the appliance Transporting the appliance 1 Warning: The washing machine is very heavy. There is a risk of injury. Exercise care when lifting the appliance. • Do not lay the washing machine on its front nor on its right side (as seen from the front). Electrical components may get wet. • Never transport the appliance without using the transit packaging. Only remove the transit packaging when the appliance is in its place of installation.
3 Special spanner A and sealing caps B (2 units) and C (1 unit) come with the appliance. 3. Use special spanner A to remove screw D and the compression spring. 4. Use sealing cap C to cap the hole. 5. Use special spanner A to remove the two screws E. 6. Use special spanner A to remove the four screws F. 7. Remove transit bar G. 8. Screw in the four screws F again. 9. Use sealing caps B to cap the two large holes.
Making the appliance level The four feet of the appliance are pre-adjusted. Large degrees of unevenness can be compensated for by adjusting the four feet of the appliance. Use the special spanner supplied to do this. Important: Do not use pieces of wood, cardboard or such like to level out small degrees of unevenness in the floor. Adjust the adjustable feet instead.
Electrical Connection 1 1 Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING – THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The appliance is supplied with a 13 amp plug fitted.
1 The switch must not break the yellow and green earth cable at any point. This appliance complies with the requirements laid out in the EEC Directive 76/899. Voltage 240 V AC: Fuse rating 13amps See rating plate for further information. This appliance meets VDE requirements. Particular regulations of local electricity authorities must be observed. This appliance conforms to EEC Directive No. 82/499/EWG on radio interference.
3 Sealing rings are either inserted in the plastic nuts of the threaded hose fitting or are included as spare parts. Do not use any other sealing rings. Important! All threaded hose fittings must only be tightened by hand. 1. Connect the hose with the right-angle connector to the machine. Important! Do not position the inlet hose vertically downwards. Position it to the right or the left as shown in the illustration. 2.
When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4’’) and no less than 60 cm (23.6’’) above floor level. The upright standpipe should have a minimum, length of 30 cm (12’’) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water. Longer drain hoses are available in lengths of 2.7 and 4 metres from your Service Force Centre.
Warranty conditions Great Britain Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate.
Service and Spare Parts If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce.co.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.