L 60260 FL L 60460 FL L 60660 FL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com 2.1 Installation • Remove all the packaging and the transit bolts. • Keep the transit bolts. When you move the appliance again you must block the drum. • Do not install or use a damaged appliance. • Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the weather. • Obey the installation instruction supplied with the appliance. • Make sure that the floor where you install the appliance is flat, stable, heat resistant and clean.
ENGLISH 2.3 Care and Cleaning WARNING! Risk of injury or damage to the appliance. • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. • Do not use water spray and steam to clean the appliance. • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. 5 • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it.
www.aeg.com 4. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 7 12 1 Worktop 7 Feet for the appliance level 2 Detergent dispenser 8 Water drain hose 3 Control panel 4 Door handle 9 Water inlet valve 10 Mains cable 5 Rating plate 11 Transit bolts 6 Drain pump 12 Feet for the appliance level 4.1 Accessories 1 2 1 Spanner To remove the transit bolts. 2 Plastic caps 4 3 To close the holes on the rear side of the cabinet after the removal of the transit bolts.
ENGLISH 7 5. CONTROL PANEL 1 2 3 Cottons Eco 9 1 On/Off button 8 7 6 5 4 • You do not use the appliance for 5 minutes before you press button 4 . – All settings are cancelled. – Press button 1 to activate the appliance again. – Set again the washing programme and all possible options. • After 5 minutes from the end of the washing programme. Refer to 'At the end of programme'.
www.aeg.com The display shows: A • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme. – You change the programme while it operates.
ENGLISH • Decrease the maximum speed of the spin phase of the programme. • Activate the 'Rinse Hold' function. Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed. 'Rinse Hold' function is on. 5.9 Temperature button 9 Press button 9 to change the default temperature. = cold water 5.10 Acoustic signals function You can hear the acoustic signals when: • You activate the appliance. • You deactivate the appliance. • You press the buttons.
www.aeg.com Programme Temperature Type of load Cycle max. weight of load description Functions Cottons + Stains 95° - 40° White and coloured cotton with heavy soil. max. 6 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD EXTRA RINSE TIME SAVE1) Synthetics 60° - Cold Synthetic or mixed fabric items with normal level of soil. max. 3 kg Wash Rinses Short spin SPIN REDUCTION RINSE HOLD EXTRA RINSE TIME SAVE1) Easy Iron2) 60° - Cold Synthetic fabric items Wash with normal soil. Rinses max.
ENGLISH Programme Temperature Type of load Cycle max. weight of load description Functions Curtains 40° - Cold Set this programme to wash curtains. It adds automatically the prewash phase to clean the dust from the curtains. Do not put the detergent into the prewash compartment. max. 2 kg Prewash Wash Rinses Short spin SPIN REDUCTION RINSE HOLD EXTRA RINSE Jeans 60° - Cold All items in jeans. Jersey made items with hi-tech materials. max.
Programmes Load (kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) L 60260 FL Remaining moisture (%)1) L 60460 FL Remaining moisture (%)1) L 60660 FL 12 www.aeg.com Cottons 60 °C 6 1.20 58 146 53 52 44 Cottons 40 °C 6 0.75 58 145 53 52 44 Synthetics 40 °C 3 0.50 43 127 35 35 35 Delicates 40 °C 3 0.53 50 100 35 35 35 Wool/Hand wash 30 °C 2 0.
ENGLISH 3. Press button 1 to activate the appliance. 4. Put the laundry in the appliance. 5. Use the correct quantity of detergent and additives. 6. Set and start the correct programme for the type of laundry and soil. 13 2. Put the laundry in the drum, one item at a time. Shake the items before you put them in the appliance. Make sure not to put too much laundry in the drum. 3. Close the door. 9.1 Loading the laundry 1. Open the appliance door.
www.aeg.com Flap for powder or liquid detergent Turn it (up or down) in the correct position to use powder or liquid detergent. Always obey the instructions that you find on the packaging of the detergent products. Check the position of the flap Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 1. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down.
ENGLISH 9.3 Setting and starting the programme 1. 2. Turn the programme knob. The indicator of button 4 flashes with red colour. 3. The indicators of the default temperature and spin speed come on. To change the temperature and/or the spin speed, press the related buttons. 4. Set the available functions and the delay start. When you press the relevant button, the indicator of the set function comes on or the display shows the related symbol. 5. 9.
www.aeg.com If the temperature and level of the water in the drum are too high, the door lock symbol stays on and you cannot open the door. To open the door do the steps that follow: 1. Deactivate the appliance. 2. Wait for some minutes. 3. Make sure that no water is in the drum. If you deactivate the appliance, it is necessary to set the programme again. 9.10 At the end of the programme • The appliance stops automatically. • The acoustic signals operate. • In the display comes on.
ENGLISH – Underwired bras. – Use a washing bag to wash small items. • A very small load can cause balance problems with the spin phase. If this occurs, adjust manually the items in the tub and start the spin phase again. 10.2 Stubborn stains For some stains, water and detergent is not sufficient. We recommend that you remove these stains before you put the items in the appliance. Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric. 10.
www.aeg.com find on the packaging of the manufacturer. Do this separately from the laundry wash. 11.2 External cleaning Clean the appliance only with soap and warm water. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents or chemical products. the drum. Make regularly a maintenance wash. To do this: • Empty the laundry from the drum. • Set the hottest cotton wash programme • Use a correct quantity of powder detergent with biological properties.
ENGLISH 3. 4. 5. 6. 11.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 19 Remove the top part of the liquid additive compartment. Clean all the parts with water. Clean the dispenser recess with a brush. Put back the dispenser in the recess. • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates.
www.aeg.com 2. 3. 4. 5. Pull back the drainage duct and turn the filter to remove it. 6. Remove fluff and objects from the pump. 7. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 8. Clean the filter under the water tap and put it back in the pump into the special guides. Make sure that you tighten correctly the filter to prevent leakages. 2 1 1 2 Put a container below the recess of the drain pump to collect the water that flows out.
ENGLISH 21 10. Close the drain pump door. 11.8 The inlet hose filter and the valve filter • The indicator of button 4 flashes and the display shows the related alarm. Refer to 'Troubleshooting'. It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. WARNING! Disconnect the mains plug from the mains socket. To clean the water inlet filters: 1. 2. Close the water tap.
www.aeg.com When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 11.10 Frost precautions 2. 3. 4. Close the water tap. Remove the water inlet hose Put the two ends of the inlet hose in a container and let the water flow out of the hose. 5. Empty the drain pump. Refer to the emergency drain procedure 6.
ENGLISH Problem Possible cause The appliance The water drain hose is does not drain the damaged. water. The programme does not start. There is water on the floor. Possible solution Make sure that the water drain hose has no damages. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. The connection of the water drain hose is not correct. Make sure that the connection is correct. A washing programme without the drain phase is set.
www.aeg.com Problem Possible cause Possible solution You cannot open the appliance door. The washing programme is in operation. Let the washing programme end. There is water in the drum. Set the drain or the spin programme. The appliance makes an unusual noise. Incorrect level of the ap- Adjust the level of the applipliance. ance. Refer to 'Installation'. You did not remove the packaging and/or the transit bolts. Remove the packaging and/or the transit bolts. Refer to 'Installation'.
ENGLISH 25 13.2 Unpacking 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door and remove all the items from the drum.
www.aeg.com 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers.
ENGLISH 27 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. – We recommend that you keep the packaging and the transit bolts for when you move the appliance. – If the appliance is delivered in the winter months when there are minus temperatures. Store it at room temperature for 24 hours before using for the first time. 13.3 Positioning and levelling • Install the appliance on a flat hard floor.
www.aeg.com CAUTION! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. Make sure that there is sufficient access after the installation for possible repairs by a qualified person. Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration.
ENGLISH Make sure not to have more than a distance of 5.02 m (16.5 ft) between the ap- 29 pliance inlet hose and the bottom of the water storage tank. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault . If this occur, close the water tap and contact the service centre to replace the hose. A 13.
www.aeg.com • If the end of the drain hose is this (see the drawing), you can push it directly into the stand pipe. Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm.
ENGLISH 31 13.6 In the interest of the environment • Connect the appliance to the FOUL system for the drain water. The sewage works keeps the drain water for the treatment before to release safely it into a river. Do not connect this appliance to the surface drain system of the water because it releases the drain water directly into a river or stream without a treatment and this can cause of pollution. Contact your local water authority to have more information. 14.
132932651-A-262012 www.aeg.
