INSTRUCTION BOOK FM 2500DD-A GB 40 325 88-8514 rev.
Your New Appliance Thank you for purchasing an AEG appliance. To enable you to use your new appliance efficiently and safely, please read this instruction book carefully before installing or using the appliance, and retain for future reference. Should the appliance be transferred to a new owner please ensure this instruction book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings.
Contents Page No. For the user Your New Appliance ........................................................................................ Safety information .......................................................................................... Product description ........................................................................................ Downdraught Extractor .......................................................................... Height positions ......................................
Contents Page No. For the electrician Unpacking ...................................................................................................... Technical data ................................................................................................ Installation........................................................................................................ Mounting ........................................................................................................
Safety Information France Germany Italy Sweden UK Senlis Nürnberg Pordenone Stockholm Slough +33 (0)3 44 62 29 29 +49 (0)800 234 7378 +39 (0)800 117511 +46 (0)8 672 53 60 +44 (0)1753 219899 Cleaning and Maintenance This downdraught extractor is designed for use in a normal domestic household. If used in any other way there could be a risk of an accident. For hygiene and safety reasons the downdraught extractor must be kept clean.
· Installation The downdraught extractor may only be installed by an authorised electrician or someone approved by the manufacturer. Work carried out by unqualified persons can lead to personal injury and/or damage to property and may damage the downdraught extractor. During installation make sure the electricity cable is not pinched. · · · The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us.
Product Description Customer Care For general enquires concerning your AEG appliance or for further information on AEG products, please contact our Customer Care Department at the address below or visit our website at www.aeg.co.
Downdraught Extractor Service and Spare Parts The air is sucked in at the air dampers through the fat filter and is then blown via the extraction hose to the extraction duct and out into the open air. In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will automatically be routed to the Service Centre covering your post code area.
How to use In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mecanicas or electrical brakedown. Downdraught Extractor Never leave the downdraught extractor unattended when deep-frying or melting fat or other easily ignited substances. Do not flambe food in the immediate proximity of a downdraught extractor that is switched on. This can cause fire.
What to do if... If the appliance is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. Downdraught Extractor 1. To turn the downdraught extractor on, press . 2. To select the height position, press . k IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
The downdraught extractor will then stop rising automatically when the button is released or when top position is reached. Overview of the outside width of the units 180 mm Downdraught Safety If the downdraught extractor is obstructed when raising, it will switch off automatically. 360 mm Glass ceramic hob with 2 cooking zones Gas hob with 2 burners Induction hob with 2 cooking zones Grill Grill / Fryer Wok Lowering 1. Press l.
Raising When the downdraught extractor is switched on. Select the height position within 10 seconds. 1. Press . The downdraught extractor will move to top position and switch on at extraction rate 1. The dampers will deploy on the way up. Mounting: When mounting several hobs together you must use a reinforcement beam between each hob as well as the silicone supplied with the hobs (see fig.) 1. Cut a hole of the calculated size in the table top 2. Place the individual hobs upside down on a mat.
Mounting more than one hob Extraction rates The downdraught extractor can be set to three levels and intensive extraction. Level 1: 150 m³/h Level 2: 220 m³/h Level 3: 345 m³/h Intensive extraction: 480 m³/h Distance to wall: Min. 150 mm (flammable material) Distance to wall: Min. 50 mm (non-flammable material) m 0m 49 Reinforcement beam Setting the extraction rate When the downdraught extractor is on, raised and at rate 1. < 1.
Intensive extraction Cutting Out The downdraught extractor is on and raised. When fitting this product: read the instructions on this page. When fitting this unit in conjunction with other units: read the instructions on the following page. 1. Press b. The downdraught extractor will extract on intensive for 5 minutes. It will then return automatically to its last setting before intensive extraction was activated.
Mounting Time-controlled switching off The unit may be mounted in any type of kitchen worktop with a thickness of 28 to 40 mm. You can set the downdraught extractor to switch off automatically at a later time. Time-controlled switching off can be set from 1 to 99 minutes. Position It is advisable to position the downdraught extractor immediately next to the hob.
When the time set has passed, suction strength is switched off. The downdraught extractor remains in the height position set. 3. Fitting the cover plate Fit the cover plate as follows: 1. Position the cover plate against the glass on the top cabinet. 2. Position the cover plate against the top cabinet. 3. Mark the four holes on the top cabinet, using the cover plate as a template. 4. Remove the cover plate and drill the four marked holes with a 3.2mm drill. 5. Take the backing off the tape. 6.
Correct ventilation Installation beside a gas appliance The extractor works best when there is low pressure in the kitchen. Therefore, the kitchen windows must be closed when the extractor is in operation. At the same time, it is a good idea to open a window in an adjacent room; see fig. If the downdraught extractor is installed beside a gas appliance, it must only be operated in top position and extract from the other side, i.e. the damper closest to the gas appliance must be closed permanently.
Cleaning and maintenance The product should be kept clean for reasons of hygiene and safety. Never use metal cleaning pads, metal sponges, hard plastic sponges, scouring powder, soft soap or other abrasive and caustic cleaners. Top cabinet Connection The top cabinet may become spattered with fat from frying. Min. cable size: 0.75 mm² Cable type: HO5VV-F To clean 1. Switch the extractor on and raise it to the top position. 2. Lift the top cabinet off. 3.
Installation 7. Assemble the filter, spring and top cabinet in reverse order. The filter must be completely dry before it is re-fitted in the extractor. 8. Reset the filter cleaning indicator by pressing and simultaneously for 3 seconds. "CL" will disappear from the display. If you clean the filter before the tablemounted cooker hood has been in use for 30 hours ("CL" has not appeared on the display), the filter cleaning indicator can be reset in the same way.
Unpacking Check that the appliance has no faults and is undamaged on delivery. Technical Data Model FM 2500DD-a: Transport Damages Any damages resulting from a transport which you have not performed yourself must be communicated to the dealer within one week of receipt of the product. On the rating plate which is placed on the back of the product you will find the CE marking and the product’s serial number.