FAVORIT 88060 VI EN DISHWASHER USER MANUAL
FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
Contents 3 CONTENTS 4 8 9 11 12 13 13 14 15 15 18 19 21 23 24 Safety information Product description Control panel Use of the appliance Setting the water softener Use of dishwasher salt Use of detergent and rinse aid Multitab function Loading cutlery and dishes Washing programmes Select and start a washing programme Care and cleaning What to do if… Technical data Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and information
Safety information SAFETY INFORMATION Before the installation and use, read this manual carefully: • For your safety and the safety of your property. • To help the environment. • For the correct operation of the appliance. Always keep these instructions with the appliance also if you move or give it to a different person. The manufacturer is not responsible if an incorrect installation and use causes damage.
Safety information 5 • Fill the appliance with salt before you start a washing programme. Remaining salt in the appliance can cause corrosion or make a hole in the bottom of the appliance. • Do not fill the rinse aid dispenser with other products than the rinse aid, (dishwasher cleaning agent, liquid detergent). This can cause damage to the appliance. • Make sure that the spray arms can move freely before you start a washing programme.
Safety information • Make sure not to squash or cause damage to the water hoses when you install the appliance. • Make sure that the water couplings are tight to prevent a water leakage. • The first time you use the appliance, make sure that the hoses do not have water leaks. • The water inlet hose has a safety valve and a double sheath with an inner mains cable. There is pressure in the water inlet hose only when the water flows.
Safety information 7 WARNING! Visible led radiation, do not look directly into the beam. The LED of the lamp is CLASS 2 and agrees with IEC 60825-1: 1993 + A1:1997 + A2:2001. Emission wave length: 450 nm Maximum emitted power: 548 μW To replace the internal lamp, contact the service centre. Disconnect the mains plug from the mains socket before the replacement of the internal lamp. Service centre • Only a qualified person can repair or work on the appliance. Contact the service centre.
Product description PRODUCT DESCRIPTION 10 1 9 2 3 4 5 1 2 3 4 5 6 7 8 9 10 Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser Rating plate Filters Lower spray arm Upper spray arm Top spray arm TimeBeam TimeBeam shows, on the kitchen floor, the washing programme time or the countdown of the delay start. With TimeBeam you always know the remaining time of the washing programme and of the delay start.
Control panel 9 • The end of the washing programme, a zero shows on the kitchen floor • The countdown of the delay start with steps of one hour (24h, 23h...). TimeBeam goes off when the appliance is deactivated. CONTROL PANEL The controls are on the top on the control panel. To operate with the controls, keep the appliance door ajar.
Control panel • The activation and deactivation of the rinse aid dispenser (only with the multitab function on) • The number of the washing programme • The remaining time to the end of the washing programme • The end of a washing programme (the display shows a zero) • The time of the delay start • The alarm codes • The activation and deactivation of the acoustic signals. Delay touchpad Press this touchpad again and again to delay the start of the washing programme from 1 to 24 hours.
Use of the appliance 11 Activate the appliance. The appliance is in setting mode when: • The display shows two horizontal status bars. Activate the appliance. The appliance is not in setting mode when: • The display shows the time of the washing programme or of the delay start. – It is necessary to cancel the programme or the delay start to go back to the setting mode. Refer to 'Select and start a washing programme'.
Setting the water softener If you use the combi detergent tablets ('3 in 1', '4 in 1', '5 in 1'), use the multitab function (refer to 'Multitab function'). SETTING THE WATER SOFTENER The water softener removes minerals and salts from the water supply. These minerals and salts can cause damage to the appliance. Adjust the level of the water softener if this does not agree with the water hardness in your area. Contact your local water authority to know the water hardness in your area.
Use of dishwasher salt 13 Electronic adjustment 1. Activate the appliance. Make sure that the appliance is in setting mode. 2. Press and hold touchpad (4) and touchpad (5) at the same time until the indicators of touchpads (3), (4) and (5) flash. 3. Release touchpad (4) and touchpad (5). 4. Press touchpad (3), • The indicators of touchpads (4) and (5) go off. • The indicator of touchpad (3) continues to flash. • The acoustic signals sound.
Multitab function 2. Put the detergent in the dispenser . 3. If the washing programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. If you use the detergent tablets, put the tablet in the detergent dispenser . 5. Close the detergent dispenser. Press the lid until it locks into position. Use long washing programmes when you use the detergent tablets. These cannot fully dissolve with short washing programmes and can decrease the washing results.
Loading cutlery and dishes 15 2. 3. 4. 5. Fill the salt container and the rinse aid dispenser. Adjust the water hardness to the highest level. Start a washing programme without dishes. When the washing programme is completed, adjust the water softener to the water hardness in your area. 6. Adjust the quantity of rinse aid. LOADING CUTLERY AND DISHES Refer to the leaflet 'Examples of ProClean loads'.
Washing programmes Programme 4 Type of soil Type of load Programme description Fresh soil Crockery and cutlery Wash 60 °C Rinse Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry 6 Light soil Crockery and cutlery Wash 55 °C Rinses 7 Normal or light soil Delicate crockery and glass- Wash 45 °C ware Rinses Dry 8 Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance.
Washing programmes Programme Extra-Hygiene ÖKO PLUS 5 Yes, with effect Yes, with effect 6 Yes, with effect Yes, without effect 7 Yes, without effect Yes, with effect 8 Yes, without effect Yes, without effect Consumption values Programme Programme time (minute) Energy (kWh) Water (litre) 1 90 - 160 0,9 - 1,7 8 - 15 2 140 - 160 1,4 - 1,6 13 - 14 3 200 - 220 1,1 - 1,2 9 - 11 4 30 0.
Select and start a washing programme The water pressure and temperature, the variations of the mains supply and the quantity of dishes can change the consumption values. SELECT AND START A WASHING PROGRAMME Starting the washing programme without delay start 1. Activate the appliance. Make sure that the appliance is in setting mode. 2. Set the washing programme. • The number related to the washing programme flashes in the display. 3. If necessary, set the Extra-Hygiene or ÖKO PLUS function.
Care and cleaning 19 Interruption of a washing programme • Open the appliance door. – The washing programme stops. • Close the appliance door. – The washing programme continues from the point of interruption. Cancelling the washing programme If the washing programme has not started, you can change the selection. To change the selection while the washing programme operates, it is necessary to cancel the programme. • Press the RESET touchpad until the display shows two horizontal status bars.
Care and cleaning 1. Turn the filter (A) counterclockwise and remove it out from filter (B). B A 2. Filter (A) has two parts. To disassemble the filter, pull them apart. 3. Fully clean the parts with water. 4. Put the two parts of the filter (A) together and push. Make sure that they assemble correctly in each other. 5. Remove the filter (B). 6. Fully clean the filter (B) with water. 7. Put the filter (B) to its initial position. Make sure that it assembles correctly in the two guides (C). 8.
What to do if… 21 WHAT TO DO IF… The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. With some malfunctions, the display shows an alarm code: - The appliance does not fill with water • - The appliance does not drain the water • - The anti-flood device is on. • WARNING! Deactivate the appliance before you do the checks. Malfunction The appliance does not fill with water.
What to do if… Malfunction Possible cause The delay start is set. Possible solution • Cancel the delay start. • When the countdown is completed, the washing programme starts automatically. After the check, activate the appliance. The programme continues from the point of interruption. If the malfunction occurs again, contact the service centre. If the display shows other alarm codes, contact the service centre. The necessary information for the service centre is on the rating plate.
Technical data Problem Possible cause Possible solution The detergent can be the cause. Use a different brand of detergent. The dishes are wet. The washing programme was without a drying phase or with a decreased drying phase. For better drying results, keep the door ajar for some minutes. The dishes are wet and matt. The rinse aid dispenser is empty. Fill the rinse aid dispenser with rinse aid. The multitab function is on (this function automatically deactivates the rinse aid dispenser).
Environment concerns The rating plate on the inner edge of the appliance door shows the electrical connection data. If the hot water comes from alternative sources of energy, (e.g. solar panels, photovoltaic panels and aeolian), use a hot water supply to decrease energy consumption. ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
www.aeg.