EN User Manual Dishwasher FAVORIT34300IM0
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 4 3. PRODUCT DESCRIPTION.............................................................................................. 6 4. CONTROL PANEL...........................................................................................................7 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH 5 • The appliance can release hot steam if you open the door while a programme operates. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.5 Service WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous.
www.aeg.com 3.
ENGLISH 4. CONTROL PANEL 1 2 6 1 2 3 4 On/off indicator Programme marker Indicators Delay button 3 5 4 5 Start button 6 Programme knob 4.1 Indicators Indicator Description Washing phase. It comes on when the washing phase operates. Drying phase. It comes on when the drying phase operates. End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.
www.aeg.com 5. PROGRAMMES Programme 2) 3) 4) Degree of soil Type of load Programme pha- Consumption values ses 1) Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 195 1.039 11 Heavy soil Crockery, cutlery, pots and pans • • • • Prewash Wash 70 °C Rinses Dry 140 - 160 1.3 - 1.5 13 - 15 Normal soil Crockery and cutlery • • • • Prewash Wash 65 °C Rinses Dry 100 - 120 1.2 - 1.5 15 - 17 All • Prewash 14 0.
ENGLISH can set the programme selection mode in the following way: 9 The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales. Press and hold Start until the start indicator starts to flash. The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area.
www.aeg.com 5 flashes + pause + 5 flashes = level 5. 4. Press Delay again and again to change the setting. Each time you press Delay the level number increases. After level 10 you will start again from level 1. 5. Turn knob to on/off position to confirm the setting. 7. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4.
ENGLISH 7.2 How to fill the rinse aid dispenser A D B C M AX 4 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. 1 3 2 + CAUTION! Only use rinse aid specifically designed for dishwashers.
www.aeg.com A 30 B • On/off indicator and start indicator are on. D Starting a programme with delay start 20 C 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent in the compartment (D). 4. Close the lid. Make sure that the release button locks into position. 8.
ENGLISH 13 9. HINTS AND TIPS 9.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
www.aeg.com • Put light items in the upper basket. Make sure that the items do not move. • Make sure that the spray arms can move freely before you start a programme. 9.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct.
ENGLISH 15 CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 10.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 10.3 External cleaning 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7.
www.aeg.com Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems the end indicator flashes intermittently indicating a malfunction. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre.
ENGLISH 17 Problem and alarm code Possible cause and solution The program lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. Small leak from the appliance door. • The appliance is not level. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not level.
www.aeg.com Problem Possible cause and solution There are whitish streaks or bluish layers on glasses and dishes. • The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position. • The quantity of detergent is too much. There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid selector to a higher position. • The quality of the rinse aid can be the cause. The dishes are wet.
ENGLISH 19 12. TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 575 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 0.50 Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values.
100009560-A-102015 www.aeg.
