FAVORIT 88060 VI DISHWASHER USER MANUAL
CONTENTS 4 6 7 8 10 12 15 18 19 21 SAFETY INFORMATION PRODUCT DESCRIPTION CONTROL PANEL PROGRAMMES OPTIONS BEFORE FIRST USE DAILY USE CARE AND CLEANING TROUBLESHOOTING TECHNICAL INFORMATION ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste.
ENGLISH 3 FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. CHILDREN AND VULNERABLE PEOPLE SAFETY WARNING! Risk of suffocation, injury or permanent disability.
ENGLISH ble. Contact Service or an electrician to change a damaged mains cable. • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • Only for UK and Ireland. The appliance has a 13 amp mains plug. If it is necessary to change the fuse in the mains plug, use a 13 amp ASTA (BS 1362) fuse. 5 completed.
PRODUCT DESCRIPTION 1 2 3 12 11 10 9 8 7 6 5 4 1 Top spray arm 2 Upper spray arm 7 Water hardness dial 8 Rinse aid dispenser 3 Lower spray arm 4 Filters 9 Detergent dispenser 10 Cutlery basket 5 Rating plate 6 Salt container 11 Lower basket 12 Upper basket TIME BEAM Time Beam is a light beam that shows, on the kitchen floor: • The programme duration. It decreases with steps of one minute. • The end of the programme (0:00). • The time of the delay start.
ENGLISH CONTROL PANEL 1 2 3 4 5 6 7 8 9 1 On/off button 2 Display 6 ÖKO PLUS touchpad 7 Multitab touchpad 3 Delay touchpad 4 Programme touchpad 8 RESET touchpad 9 Indicators 5 ExtraHygiene touchpad Indicators Salt indicator. This indicator is off while the programme operates. Rinse aid indicator. This indicator is off while the programme operates. End indicator.
PROGRAMMES Programme Type of soil Type of load 1 All Prewash Crockery, cutlery, Wash 45 °C or 70 °C pots and pans Rinses Dry ExtraHygiene ÖKO PLUS Heavy soil Prewash Crockery, cutlery, Wash 70 °C pots and pans Rinses Dry ÖKO PLUS 1) 2 2) 3 Programme phases Options 3) Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry Wash 60 °C Rinse ExtraHygiene 4) Fresh soil Crockery and cutlery Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry ExtraHygiene ÖKO PLUS 6 Light
ENGLISH Consumption values Programme 1) Duration (min) Energy (kWh) Water (l) 1 90 - 160 0.9 - 1.7 8 - 15 2 140 - 160 1.4 - 1.6 13 - 14 3 200 - 220 1.1 - 1.2 9 - 11 4 30 0.8 9 5 160 - 170 0.9 - 1.0 9 - 11 6 50 - 60 1.0 - 1.1 10 - 11 7 70 - 80 0.8 - 0.9 11 - 12 8 14 0.1 4 1) The water pressure and temperature, the variations of the mains supply, the options and the quantity of dishes can change the programme duration and the consumption values.
OPTIONS MULTITAB FUNCTION ÖKO PLUS Activate this function only when you use the combi detergent tablets. This function deactivates the flow of rinse aid and salt. The related indicators are off. The programme duration can increase. This function decreases the temperature in the drying phase. The energy consumption decreases by 25%. The dishes can be wet at the end of the programme. We recommend that you keep the door ajar and let the dishes dry.
ENGLISH 5. Press touchpad (5) to change the setting 6. Deactivate the appliance to confirm. SETTING THE TIME BEAM COLOUR Nine colours are available for this light beam. You can change the colour or deactivate it. 1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indica- 11 tors of touchpads (3), (4), (5) and (6) flash. 4.
BEFORE FIRST USE 1. Make sure that the set level of the water softener agrees with the water hardness in your area. If not, adjust the water softener. Contact your local water authority to know the water hardness in your area. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Processing residues can stay in the appliance. Start a programme to remove them. Do not use detergent and do not load the baskets.
ENGLISH 13 Manual adjustment Turn the water hardness dial to the position 1 or 2. Electronic adjustment 1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in setting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold touchpads (4) and (5) at the same time until the indicators of touchpads (3), (4), (5) and (6) flash. 4. Press touchpad (3). • The indicators of touchpads (4), (5) and (6) go off. • The indicator of touchpad (3) continues to flash.
FILLING THE RINSE AID DISPENSER CAUTION! Only use rinse aid for dishwashers. Other products can cause damage to the appliance. B A M AX 4 3 2 The rinse aid, during the last rinsing phase, helps to dry the dishes without streaks and stains. 1 + - C D 1. Press the release button (D) to open the lid (C). 2. Fill the rinse aid dispenser (A), no more than the mark 'max'. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid.
ENGLISH 15 DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in setting mode. Refer to ’SETTING AND STARTING A PROGRAMME’. • If the salt indicator is on, fill the salt container. • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. 5. Set and start the correct programme for the type of load and soil.
USING THE DETERGENT A CAUTION! Use only detergents for dishwashers. B 30 4 MAX + 32 - 1 20 C 1. Press the release button (B) to open the lid (C). 2. Put the detergent in the compartment (A) . 3. If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. 4. If you use detergent tablets, put the tablet in the compartment (A). 5. Close the lid. Make sure that the release button locks into position.
ENGLISH 2. Press the delay touchpad again and again until the display shows the delay time you want to set (from 1 to 24 hours). • The delay time flashes in the display. • The delay indicator is on. 3. Close the appliance door. The countdown starts. • If you open the door, the display shows the countdown of the delay start that decreases with steps of 1 hour. • When the countdown is completed, the programme starts. Opening the door while the appliance operates If you open the door, the appliance stops.
CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. CLEANING THE FILTERS C C A B A1 A2 CLEANING THE SPRAY ARMS Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. EXTERNAL CLEANING Clean the appliance with a moist soft cloth.
ENGLISH 19 TROUBLESHOOTING The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact Service. With some problems, the display shows an alarm code: • - The appliance does not fill with water. • - The appliance does not drain the water. • - The anti-flood device is on. WARNING! Deactivate the appliance before you make the checks. Problem Possible cause Possible solution The programme does not start.
THE WASHING RESULTS AND DRYING RESULTS ARE NOT SATISFACTORY Problem Possible cause Possible solution The dishes are not clean. The filters are clogged. Clean the filters. The filters are not correctly assembled and installed. Make sure that the filters are correctly assembled and installed. The spray arms are clogged. Remove remaining soil with a thin pointed object. The programme was not applicable for the type of load and soil.
ENGLISH Problem Dry water drop stains on glasses and dishes. 21 Possible cause Possible solution The quantity of detergent was too much. Make sure that you add the correct quantity of detergent in the dispenser before you start a programme. The released quantity of rinse aid was not sufficient . Increase the released quantity of rinse aid. The quality of the detergent Try a different brand of decan be the cause. tergent. The dishes are wet. • The programme had no drying phase.
Water supply 1) Cold water or hot water2) Capacity Place settings max. 60 °C 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 2) If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption.
ENGLISH 23
www.aeg.