Ry /90 a2 Contents Safety instructions Page Far the electrical installer 28 Father kitchen furniture installer 2828 Before installing General 30 Appliance description a0 Technical data: Dimensions 30 Electrical connection values 31 ~ Fan outputs 31 Air outlet-exhaust air 31 Accessories/installation materials 32 Preparing o install Preparing for exhaust air operation 32 — Preparing the wall box (exhaust air operation) 33 — Position of exhaust air opening 33 — Special accessories Exhaust air hoses 34 Preparin
For the electrical installer For the kitchen furniture installer 28 Safety instructions Arrangement of the protective contact plug socket inside the chimney cover plate (Fig. E0/2) confers two advantages: 1. The plug socket is not visible. 2. You can easily DE-energize the appliance where necessary by unplugging it. For the necessary fixed connection, the fume extractor hood may be connected only by an electrical installer registered with the electricity board covering your area.
SIKKIM 1189 SIKKIMESE GUMBEL in doubtful cases, please seek the advice and consent of the competent area chimney-sweep or the local building authorities. Since, in spaces without fireplace, the rule is: “Supply air opening as large as exhaust air opening”, the efficiency of the exhaust air device may be impaired by the greater opening of §00—600 cm®, Operation of the hood as a return alr hood in such circumstances is safe and is not subject to the regulations noted above.
General Appliance description Technical data 30 The fume extractor hood is supplied as an exhaust air appliance and may be used as a return air appliance through application of an active carport filter {special accessory}. For this purpose, you need the AEG Original Active Carbon Filter {see special accessories). Light switch Blower switch (On/Off) Blower switch settings D = Metal filter grille (fat filter) A B < The fume extractor hood is switched on.
LANDLESS GB/EU TOME 790 — TOMATO S/ Connection value: 860D 8609 D Total connected load: 179 W 180W Fan motor: 2x B2W 2x 82W Lighting Tx 15W 1x 16W {fluorescent lamp} (fl. lamp} Fan outputs (settings) to DIN 44 871 860/8609D Setting 1 Setting Setting Setting 4 Exhaustion 200m¥h 320 m¥%h 400 mih 820 m¥/h Return air 140mi/h 240m%h 280 m¥h . 360 m¥fh Exhaust alr shyster 128 mm dia. Alr outlet arranged centrally above Pipe connection of 125 mm dia. for exhaust dir hoses of 128 mm dia.
Preparing for exhaust air operation Accessories/installation materials 1 wall rail (for mounting of fume extractor hood} 4 wall plugs for 8 mm, 40 mim long wood sowers {for mounting of chimney retaining plate on wall and wall rail) 4 button-head wood screws, DIN 7996 2 wall plugs for 5 rmm, 30 rmm long wood screws {for mounting of clamping piece} 2 button-head wood screws, 6 x 3010 DIN 1 drilling template for appliance mounting 1125 mm dia, 800 mm long hose 2125 mm dia.
SHELLEY 37— LAO 5780 If the Pitcher fume is run out into the open air through the external wall, you need a type MKZ telescopic wall box {with exhaust and supply air} (E-No, 610899004} (from our range of special accessories). Applet = Exhaust air Zulu ft = Supply air The dimensions and position of the air outlet opening are given in the following diagram.
, Special accessories Exhaust air hoses Preparing for return air operation For wall bitumen extractor hood connection, it is best lo use the non-flammable exhaust air hose under E-No. 610899008 {125 mm aid) from our range of special accessories. “The mute extractor hood is used as a return air hood when no ventilation shaft or queer wall is available. For operation as a return air hood, it is necessary to install 2 active carbon filters K1L.600 (E-No. 610899470) for kitchen fume absorption.
Geed If the kitchen fume is discharged into the open air through the outer wall, you need a telescopic wall box (E-No. 810899004) {for your own account from our range of special accessories) {Fig. CJ). See the following illustration for the dimensions and position of the air outlet opening. To connect the wall box/fume extractor hood, you are recommended to use the 125 mm dia. non-flammable exhaust air hose (E-N.
Wall mounting 36 installation steps for exhaust air operation 1. Hold the installation tern plate {with readable lettering) or the wall, noting the distance between the upper edge of the hob and the lower edge of the fume extractor hood! {Electric/gas cookers 650 mm) (0il and coal cookers min. 700 mm). 2. Mark out and drill the 8 mm dia. holes. Insert the wall plugs and mount the wall rail {Fig. EQ/3}, i £C The wall rail can' be horizontally aligned by shifting the sliding elements.
MW 5790 GEL Remove the previously available exhaust air hose £, Installing the chimney equalizer (Fig. EOE) flush with the ceiling Drill holes to take plugs for strews on the RH and LH sides of the fume extractor hood 50 mm from the lower edge of the calling and screw in the screws until they are 5 mm away from the wall. Turn back the set-screw 1o its fullest extent by turning to the left. Mount the chimney equalizer {Fig. EOE) via the wall screws.
Additional installation work for return air operation 38 installation steps same as for exhaust air operation under points 14 Further installation steps: 5. Elide guide piece {Fig. EQUINE) on to chimney cover plate {Fig. EO/4). EC 6. Fix exhaust air hose on guide piece with 125 mm dia. hose clip. 7. Fix chimney equalizer as under exhaust air. 8. Uncle the ventilation grille (Fig. EQUINE) from the chimney cover piste and, after pulling off the foil (double adhesive tee} {Fig.
GUTTED 5400 BISQUE Allow me to introduce myself: | am your new AEG fume extractor hood. From now on, | should fiche 1o help you keep your kit~ teen free from fire and fat deposits, Not simply because of my attractive appearance, but also thanks to my “intrinsic qualities™ 1am economical in terms of energy consumption, quit, powerful, easy o operate, and simple 1o care for.
For the user 40 Safety instructions it must he ensured that hobs are always covered so that the appliance Is not damaged by excessive heat liberation. Open fireplaces on oil-, gas-, and coal-fired cookers must be avoided. During deep-frying over a cooker/hob, the appliance used for deep-frying must also e supervised during operation. The oil contained in the deep-frying appliance may spontaneously ignite through overheating. ¥ contaminated oil is used, spontaneous ignition may occur even more readily.
Operation 42 First use My sliding switches are arranged on the RH side {(when viewed below from the front). The individual numbers and symbols have the following _ meanings {from left to right): 0 Lighting On Lighting Off Lighting Blower On Blower Off FRE = Blower setting switch 1 = Bower settling 1 2 = Somersetting ] 3 = Blower setting 3 4 = Blower setting 4 = To switch or the {ume extractor hood, set rmy blower switch to the “On" position g The bio war of the furn extractor hood runs.
abbey DENT 11788 — WEFT 1188 WAKE 13782 The build-in fume extractor hood is to be switched on before wooing begins and allowed 1o run on around 15 minutes after cooking is completed. ‘You should remove my metal fat filter (Fig. EW) from the appliance every 6--8 weeks and wash it by hand or in your dishwasher. The active carbon filter must be changed not later than after year. The active carbon filter cannot be washed or regenerated.
Cleaning the metal fat filter Active carbon fitter To remove and then clean my metal fat filter grille, proceed as follows: For reasons of safety against any unintentional switching on, remove my screw-in fuse from the holder or switch off my automatic using system in the fuse box. 1. Press the rock on the fat filter rifle inwards and detach the fat filter &t the front and rear. Clean my internal housing only with warm washing-up liquid suds (never use any abrasive cleaners, brushes, or scouring agents). 3.
easel WK 890 2. Remove old active carbon filters (always 2) by loitering the knurled screw in the center. 3. Clean my internal housing only with warm washing-uh liquid suds (never use any abrasive cleaners, brushes, or scouring agents), 4. Insert 2 new active carbon filters KL 600. The active carbon filter is arranged before the motor housing and is mounted with the knurled screw. 5. Re-insert the fuses and reconnect the appliance.
Changing the fluorescent lamp (starter) You can change the fluorescent lamp or starter yourself! DE-energize the appliance before changing the lamp {e.g. put aut the mains hug. 1. Elide the lighting cover to the right (860 D) or uncle and detach it {8609 Unscrew my defective fluorescent lamp by twisting out of the sockets to the left and replace it with anew one. important: Insert only a max.
abbey WELL 590 — W 14759 3. Remove any defective starter by twisting out of the socket to the left. insert a new starter by twisting to the right. 4. Re close my lamp cover. Re-insert the fuses and reconnect the appliance. Important! To clean the fume extractor hood, DE-energize the appliance {e.g. pull out the mains plug).
Special accessories Active carbon filter KL 600 £-No. 810 890 470 {2 units) Wall box MKZ ’ E-No. 610 699 004 Height x width in mm {External dimensions 250 % 220 Opening 185 x 210} Exhaust air hose E-No. 610 899 008 125 e dia, aluminum Please note that the MK2 wall box and associated accessories are not avail at the UK.
KOD 11488 GABLE Customer service in case of any inquiries and faults, please call our service center (seg list of service centers) When calling, please state the following: ‘1. The model designation 2. The E-No. 3. The F-No. You will find these data on the nameplate after opening the fat filter grille inside the appliance. In the interests of technical progress, the manufacturer reserves the right to make design and color alterations without prior notice.