7509 D Einbau-Flachschirm-Dunstabzugshaube Built-In- Flat-Screen Fume Extractor Hood Montage- und Gebrauchsanweisung Installation and Operating Instructions
Summary Safety warnings For the electrical installer For the kitchen furniture installer Page 30 30/31 Before installation General information Appliance description Technical data: - Dimensions - Electrical connection data - Air outlet - Accessories/installation material 32 32 33 33 33 34 35 Installation Preparation of the cabinet Installation of the cooker hood Recycling installation Evacuation installation 36 37-40 41/42 43/44 Electrical connection 45/46 Safety warnings for the user 47 Appliance
Safety warnings For the electrical installer The installation of a socket immediately above the cooker hood or the cabinet has two advantages: 1. The socket is out of sight 2. If necessary, the cooker hood can be disconnected by removing the plug. Should it be necessary to connect the hood permanently, this should be carried out only by a qualified electrician or a competent person. Connect the hood to the mains supply via a double pole switch which has 3mm minimum clearance between the contacts.
General information This cooker hood features a through flow retractable visor which offers a large collection area for contaminated air once it is extended into its working position. The functions are selected through the sliders; the opening of the visor can be used to switch the appliance on when the controls have been pre-set. The cooker hood can be used either in recirculation or evacuation mode.
Accessories/installation material Air outlet Air outlet 120 mm Ø 1 ducting spigot Ø 120mm 1 ring Ø 120-125mm 1 ducting spigot Ø 150mm 1 break-off wall infill spacer to be applied on the lower part of the cooker hood to cover the hollow space up to the wall 1 venting grille Ø 120mm 2 brackets to fix the cooker hood 3 screws (A) 9 screws (B) 2 screws (C) Air outlet 125 mm Ø Air outlet 150 mm Ø 34 ATTENTION: The installer should ensure that the material for the connection of the cooker hood to the evacua
Installation Preparing the cabinet Make a 505 x 165mm hole on the bottom of the cabinet 1). The measure A must be calculated by the installer according to the requested alignment between the lower visible part of the cooker hood and the cabinet. If the cabinet is without bottom 2), fix the two brackets at a distance B of minimum 30mm and maximum 60mm. Before carrying out the installation, the wooden transportation protections screwed on the visor and on the canopy body must be removed.
Installation Fit the cooker hood in the cabinet until it is well fixed to the butterfly quick fixing system placed on the lower part of the cabinet or on the two brackets. The lower visible part of the cooker hood can be adjusted (max 20mm) for the horizontal alignment with the cabinet. Partially loosen the four screws fixing the lower part of the cooker hood to the upper part 1), adjust the lower part of the cooker hood 2) in the desired position and tighten the screws definitively.
Front strip If you wish to replace the factory fitted front strip with a wooden one or with a front strip made with the same material as the kitchen, remove the five screws. Remove the front strip. If the cooker hood is to be installed in recirculation mode then charcoal filters (on request) must be provided. Recirculation fitting Fix the new front strip with the central screw before and, later, fasten the other four screws definitely.
Recirculation fitting Connect a suitable length of ducting to the air outlet on the top of the cooker hood inside the cabinet. The ducting should be long enough to project through the hole in the top of the cabinet. If you wish to install the appliance in evacuation mode, the charcoal filters are not required. Ducting fitting Fit the venting grille over the ducting and screw the grille to the top using the screws provided. Ensure that the blades in the grille are angled forwards.
Electrical connection Evacuation fitting Replace the metal filters. Your appliance must be connected to fixed wiring via the use of a double pole switched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. It is now possible to install the ducting.
Safety warnings The terminations laballed SUPPLY are for connection for the internal house wiring and the terminations labelled LOAD are for the appliance.
Appliance description/controls Controls To switch on the cooker hood slide the switch marked M selecting the required fan speed. The symbols and numbers have the following meaning: Motor Lighting M = Motor switch L = Lighting switch 0 1 2 3 0 = Lighting is off 1 = Lighting is on = = = = The motor is off Low speed Medium speed Top speed Controls The movement of the visor can be used to switch the appliance on and off. To switch on the worktop lighting slide the switch L to position 1.
Cleaning and maintenance Before carrying out any kind of maintenance, disconnect the hood form the mains supply or unplug the appliance. Metal filters The metal filters retain grease particles and are used both in evacuation and recirculation mode. The metal filters should be cleaned every 4 weeks in the dishwasher or by hand. Washing by hand Leave the metal filter in warm water with mild detergent for one hour and then rinse with warm water. The operation should be repeated if necessary.
Fluorescent Strip light replacement (Starter) A 18W fluorescent strip light ensures the lighting of the worktop. Move the glass strip until the opposite end is free. Pull the glass strip slightly downward. Fluorescent strip light replacement (Starter) Move the strip glass toward one side and remove. Replace the fluorescent strip light. To replace the fluorescent strip light operate as follows: Disconnect the hood from the mains supply. Unplug the hood.
Special accessories Fluorescent strip light (Starter) General warnings for the cleaning Turn the Starter as illustrated and replace. Charcoal filter KF 7509 E. Nr. 610 899 435 Wall box MKZ E. Nr. 610 899 004 Outside dimensions for the hole on the wall 250x220 185x210 Evacuation duct 120 mm Ø Aluminium E. Nr. 610 899 007 Evacuation duct 125 mm Ø Aluminium E. Nr. 610 899 008 Attention: To clean the cooker hood disconnect the appliance from the mains supply.
56 57
58 59
60 61
62 63
Bitte geben Sie unserem Kundendienst folgende Angaben bei einer Störung an: If your appliance has a fault, please contact our service engineer and state the following numbers: E-Nr. 610 F-Nr.
