69802 G Operating Instructions GB IE Gas hob
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation ! ! ! ! ! This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I.S.
it has been installed. Ensure there is a continuous air supply, keeping air vents in good condition or installing a cooker hood with a venting hose. ! When using the hob for a long period time, the ventilation should be improved, by opening a window or increasing the extractor speed. l Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. ! Ensure the control knobs are in the ‘OFF’ position when not in use.
Contents Important Safety Information ................................................................................ 2 Instructions for the User ........................................................................................ 5 Description of the Hob ............................................................................................... 5 Operation ....................................................................................................................
Description of the Hob 1 3 3 5 6 7 8 4 2 1. 2. 3. 4. 5. 6. 7. 8. Hob Top Rapid Burner Semi-rapid Burners Auxiliary Burner Control knob for back right burner (semi-rapid) Control knob for back left burner (semi-rapid) Control knob for front left burner (rapid) Control knob for front right burner (auxiliary) INSTALLATION Any gas installation must be carried out by a competent person, and in accordance with existing rules and regulations.
Operation Hob burners ! ! ! ! To light a burner: Push in the relevant control knob and turn it to maximum position. A - Burner cap Upon ignition, keep the knob B - Burner crown pushed down about 5 seconds. C - Ignition electrode This will allow the D - Thermocouple "thermocouple" (see diagramletter D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then adjust the flame as required.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as YES spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added.
The Burners The burner caps and crowns can be removed for cleaning. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition electrode The electric ignition is obtained through a ceramic "electrode" and a metal electrode (see figure-page 6 - letter C).
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM $ There is no spark when lighting the gas SOLUTION % % % % $ The gas ring burns unevenly % % Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
Instructions for the Installer Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: Height: 580 mm. 510 mm. 88 mm. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.
Instructions for the Installer BURNER RAPID (large) TYPE OF GAS POSITION NATURAL GAS 20 mbar VALUE = 37.78 MJ/m3 Ws - 50.7 MJ/ m3 LPG GAS 28-30/37 mbar VALUE = 49.92 MJ/Kg SEMI-RAPID (medium) AUXILIARY (small) MAX MIN MAX MIN MAX NOMINAL THERMAL POWER kW 2.9 0.75 1.9 0.45 1.0 0.33 NOMINAL FLOW RATE m3/h 0.276 0.062 0.181 0.043 0.095 0.031 119 Adjust. 96 Adjust. 70 Adjust. NOMINAL THERMAL POWER kW 2.7 0.75 1.9 0.45 1.0 0.33 NOMINAL FLOW RATE 195 46.8 137 32.
Instructions for the Installer Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom or shower room. Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm. between the rear edge of the hob and the wall. A minimum distance of 100 mm. must be left between the side edges of the hob and any adjacent cabinets or walls.
Instructions for the Installer Installation IMPORTANT This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored.
Instructions for the Installer Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob.
Instructions for the Installer Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer 0 58 If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Instructions for the Installer Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. 3 The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections.
Instructions for the Installer Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 50 Hz AC electrical supply.
Instructions for the Installer Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point.
Instructions for the Installer Fault Finding Blue Brown Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. NO YES Blue Green Yellow Brown Carry out: D: Resistance to Earth check. Carry out: C: Polarity check. Has inlet fuse blown? NO Electricity supply should now be satisfactory. YES PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Inlet wiring faulty. Rectify any fault.
Instructions for the Installer A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight. B. INSULATION CHECK Appliance electrically disconnected, all switches ON. a) meter set on Ω (Ohms) x 1 scale. Test leads from L to N in appliance terminal block.
Instructions for the Installer Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check earth continuity of appliance Check position of the electrode Check fitting of burners Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from the tip of each electrode to the t
Instructions for the Installer Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. the gas tap to the MAX position and ignite. # 1)2) Turn Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: the burner and set to # 1) Re-ignite MIN. 2) Remove the control knob.
Instructions for the Installer Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit.
Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEGElectrolux appliance or any part thereof is pro-ved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the elec-tricity supply stated on the rating plate.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area.For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
35686-0004 10/06 Grafiche MDM - Forlì www.aeg-electrolux.co.
