Equipment and description Figure 1 A Hobs with associated contrails {high-speed hob(s) on 3200 DK) B Operating pilot imp, amber € Residua heat indicator lamp D Halogen hob {1200 + 1800 W) with associated cantor! Before using for the first time Note A burning smile wiki initially be noticed with the hotplates; this will disappear completely after using the hotplates several times. Caution! ‘The hotplates become hot during boiling and frying.
The correct utensils in any case, utensils with an even hottie should be used (commercially available electric utensils or utensils made of the same glass ceramic material), since uneven pols and pans insufficiently absorb the heat from the cooking zone and thereby lead to excessively dong cooking times and damage to the hob. For the same reasons, you should not use excessively small utensils, but utensils with a size matching that of the cooking zone.
Using the hotplates Hints for cooking on hotplates, B Prefect your hotplates from moisture otherwise the plates will start to rust (3200 DK). W Keep the hotplates clean at all times because dirty plates will nat introduce Tull heating power. B Take advantage of the after heat: Turn the hotplates off 5-10 minutes before.end of cooking time. Overheated fat or oil can ignite very easily. You should therefore never leave dishes which are being cooked in fat or oil unattended {e. g. chippie.
Using the hotplates General The heating power of the hotplates can be S varied continuously by turning the control ; ARG . -nabs clockwise or counterclockwise. As-soon &g you switch on a hotplate the indicator light {figure 1/B) comes an. Boiling and frying on the hotplates (6200 DK, 6250 DK) (High speed hotplate{s) at 3200 DK) # Boiling : To parboil, select setting 3 and tum “back to 1 for boiling; use higher or dower smelting as required.
Cleaning and maintenance General Always switch off the cooking areas and iet them cool down before cleaning. Never use abrasive cleaners or scouring powders, bleach, rust or stain removers. Never place aluminum foil over the cooking areas. Wipe control panel with soft cloth, lukewarm water and washing up liquid. Ceramic hob Ceramic surfaces require regular care and cleaning although they are easier 1o clean than your “old cooking areas”.
Cleaning and maintenance Hotplates Remove stubborn dirt from thé hotplates with fine scouring powder or pad. Afterwards warm up gently and allow to dry. From dime to dime apply a little sewing machine oif to the hotplates {polishing with paper afterwards) or use a suitable cleaner/conditioner, like “C era-fix", to keep them in good condition. Never use butter, bacon, fat stc. Recommended cleaners Stael-fix for normal or heavy silage, Era-fix or Coloration for light silage and conditioning.
Installation instructions Electrical connection Warning! All appliances withal core lead must be earthed Please ensure that the voltage and current indicated on the rating plate agrees with the voltage of your electricity supply. 2201240 volts — (i. 8., 220/240 V AT) # your appliance has been equipped with 2 mains lead with a molded-on type plug, you must comply with the following regulations: The plug mounded on to the cord incorporates a fuse. For replacement, use a 13 amp BS 1362 fuse.
Installation instructions Please note before commencing installation and connection! I &t cases the appliance may only be connected to the electricity supply by an approved electrician. This will ensure that the legal requirements and conditions of connection of your local electricity supply authority are ch served. installation Please note that with fish fitting appliances the plastic covering or veneer must be applied with a heat resistant adhesive (100° C).
Installation instructions Bracing elements Figure 6 There must not be any cross strips underneath the worktop cutout. They should be swan back at least to worktop cut oyl size. The bracing range of the bracing elements extends from With thicker worktops recesses should be provided in the worktop at suitable points.
What (something does not work)? .. the yellow indicator light does not come on? M Check that you have followed alt points of the operating procedure. B Check that the fuses of the installation are OK. the indicator light for residual heat does not come on? The bulb is defective. it must be exchanged by an electrician.
AEG Exaggerate AG Posthaste 1036 D-90327 Nirenberg 1 @© Copyright by AEG AEG Domestic Appliances Ltd Customer Care Department PO Box 47, New bury Berkshire, REORG 5XL Telephone: 01835 572700 Fax: 01635 42870